709099

Novoferm Novomatic 413 Handleiding

16
Verklein
Vergroot
Pagina terug
1/45
Pagina verder
19
GB
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
• Programming the operator
Control elements
A
a.
B
C
D
Before programming
Menustage1:Programmingthestart
functionforthehandtransmitter
Menu stage 2: Programming the light
function for the hand transmitter
The controls for programming the door operator are
protected by a transparent cover. The transparent
cover can be opened with a screwdriver. After the
operator has been programmed, the transparent
cover must be closed again.
.Numerical display shows the menu stage as well
as the selected value.
Point display, lights up to indicate “ready for
operation” and flashes on the hand transmitter
code learning completion.
.Button during the setting / adjustment phase
serves as an “up” button and outside the menu as
a start button.
.Button during the setting /adjustment phase
serves as a “down” button.
.Button is used to call up the setting/adjustment
menu, to change the menu stages and to store the
settings.
The programming of the control unit is menu-driven.
By pressing button , the menu guide is called up.
The numbers displayed indicate the menu stage.
After approx. 2 seconds, the display flashes and the
setting can be altered via buttons and . The
selected setting is stored with button . And the
programme jumps automatically to the next menu
stage. By repeatedly pressing button , menu
stages can be skipped. To quit the menu, press
button until “0” is shown again. Outside the menu,
button can be used to generate a start impulse.
- Allow door to engage into the carriage.
- Pull out the mains plug. Point display (a) lights up.
- Make sure that the aerial is correctly positioned
(see figure 13).
- Observe the hand transmitter instructions.
Briefly press button . “1” is displayed. As soon as
the display flashes, press and keep pressed for
approx. 1 second the button of the hand transmitter,
with which you later wish to start the operator. As
soon as the code has been read, the red point
display (a) flashes four times before quitting.
Further hand transmitters (up to a maximum of 30)
can be programmed.
Deleating all the hand transmitters programmed
for the operator:
Menu stage 3: Setting/adjusting the top end-
of-travel position
Plug in the operator‘s main plug while pressing
button .
Keep button pressed for 3 seconds. Number 3
appears in the display 8 a.
Wait a short while until the 3 starts flashing.
Press button and make sure that the door travels in
the OPEN direction.
If the door closes in the wrong direction, after
having pressed , keep button pressed for
another 3 seconds. “3” flashes briefly. The
!
Figure
0 will be displayed. Menu finished.
Press key brieflyand figure 1 will be displayed.
Press key once again and figure 2 will be
displayed.
Press the second button at the transmitter with which
the 4-min light is to be switched on. As soon as the
code has been read in, the red point display (a) will
flash four times to acknowledge the entry. Figure 0
will be displayed. Menu finished.
14
15
16
17
travelling direction is altered.
Now travel by pressing button into the desired door
end position OPEN 17b.
By pressing button , the position can be corrected
into direction CLOSE.
Once the desired OPEN end-of-travel position has
been reached, press button . The operator stores
the OPEN end-of-travel position and “4” appears in
the display.
We recommend setting the suitable door type in
menu stage 8 prior to the force-learning cycle.
During this opening and closing cycle, the
operator learns the force required to open and close
the door. The cycles
must not be interrupted. During these cycles must
not be interrupted. During these cycles “0” appears
in the display.
- Press button . The operator causes the door to
open until the top end-of-travel position has been
reached.
- Now press button again. The operator causes
the door to close until the bottom end-of-travel
position has been reached.
- After approx. 2 seconds, “0”disappears.
- Place an obstruction (e. g. operator’s cardboard
box) underneath the doors’s closing edge.
- Starting from the OPEN end-of-travel position,
actuate the door to close.
- The door travels towards the obstruction, stops
and travels back to the top end-of-travel position.
If the door springs have been changed or altered,
then the force learning cycle must be repeated:
proceed to menu stage 5 and keep button
pressed for 3 seconds. “0” appears in the display.
Then complete the force learning cycle as explained
under point 19.
If you have previously quit the setting menu, press
button for 3 seconds until “3” appears. Then press
button twice until “5” appears.
After approx. 2 seconds, the display flashes showing
the set value of the opening force limit. The force limit
Menu stage 4: Setting/adjusting the bottom
end-of-travel position
Wait a short while until “4” starts flashing.
Press button . The operator causes the door to
travel in the CLOSE direction as long as the button is
pressed. The position can be altered to the OPEN
direction via button ..
Once the desired CLOSE end-of-travel position has
been reached, press button . The operator stores
the CLOSE end-of-travel position and “0” appears in
the display.
Force-learningcycle
Checking the force limit facility
Menu stage 5: The opening force limit
!
A force limit does not apply!
• Specialsettings
In order to access the menus for the special settings,
keep key pressed for 3 sec until figure 3 is
displayed. Press key to by-pass menu step 3.
Now keep key pressed for 3 sec until figure 5 is
displayed. Press key to by-pass menu steps.
18
19
20
setting can be increased for decreased via buttons
and .After setting the value, press button .
The display shows “6”.
After approx. 2 seconds, the display starts flashing,
and the set value for the closing force limit is
displayed.
The force limit setting can be increased or decreased
via buttons and .
After setting the value, press button . “0” appears
in the display.
Finally, check the force settings, and, if necessary,
repeat the setting procedure.
The maximum force at the main closing edge must
not exceed 150 N!
If the force setting is too high, persons may
be placed at risk of injury.
The factory setting is 4!
Keep button pressed until “7” appears in the
display.
Menu Light Warning 24V
value phase phase
0 60 s - 60 s
1 120 s - 120 s
2 240 s - 240 s
3 0 s - 0 s
4 0 s 3 s 0 s
5 60 s 3 s 0 s
6 120 s 3 s 0 s
7 60 s 0 s TAM
8 120 s 0 s TAM
9 240 s 0 s TAM
Press button .“8” appears in the display.
1 15 0 15 0
4 25 30 25 40
5 15 15 15 55
6 15 15 15 15
7 35 35 65 45
8 55 15 15 100
The factory setting of 4 must be adhered. The
softruns may only be alerted on the express per-
mission of the door manufacturer.
Press button . “0” appears in the display.
Menu stage 6: The closing force limit
Caution!
Menu stage 7: Light phases
Menu stage 8: Door fitting
Important note:
The factory setting is 1.
TAM: OPEN signal, when the door is not closed 24V
are available for signalling.
Menu Start Stop Start Stop
value open open closed closed
9 only soft run
These values correspond to the “soft” runs
measured in cm at the carriage.
When the advance warning time is set, the light and
24 V will be switched on before the drive starts
running.
0 0 0 0 0
2 0 15 0 40
3 15 15 15 35
… 16 …

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Novoferm-Novomatic-413

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Novoferm Novomatic 413 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Novoferm Novomatic 413 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 2,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info