801544
25
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
22
DETECTION SCREENS
HEDEF ID
measurement plays an important role for the device to eliminate the
false signals produced by these rocks.
Magnetic Mineralization Indicator will be displayed on screen in all
modes except for the Ground Anomaly & Cavity mode. You can remove
it by pressing the INFO button. It will come back on screen when you
press the INFO button again.
(3) Ground Balance Window
The ground balance window is divided into 2 parts: The top part shows
the instant ground balance value changes while searching and the
bottom part shows the adjusted ground balance value.
Ground Balance window will be displayed on screen in all modes except
for the Ground Anomaly & Cavity mode. You can remove it by pressing
the INFO button. It will come back on screen when you press the INFO
button again.
To learn how to ground balance the INVENIO, please read the section
titled ''Ground Balance''.
(4) Height Indicator
Shows the height of the search coil on the bar, in centimeters or inches.
The ideal search height for the type of search coil attached, is indicated
with green color. If you hold the search coil at a different height than
the recommended one, this will be indicated by red color on the bar.
(5) Depth Indicator
Shows the depth of the detected target, in centimeters or inches.
It ranges between 0 to 150+ (0-60+ in inches). In other words, for
depths greater than 150cms (60'')., it will show 150+ (60+ in inches).
Upon target detection, the bar will rise and the target depth will be
indicated numerically. Depth reading may vary based on target size
and orientation, metal type and ground conditions.
IMPORTANT! To see the target depth instantly in non-motion modes,
you need to swing the search coil more slowly.
(6) Drift - Metal bar
This bar is present only in the Basic and Expert modes.
All signals obtained by the device, as well as drifts, while searching, are
shown on this bar.
Changes in the ground and temperature, as well as environmental noise,
may lead to negative and positive drifts. During negative drifts, the bar
will fill up in the DRIFT direction, in proportion to the strength of the
drift.
When the device detects a metal or a positive hot rock or if a positive
drift occurs, the bar this time will fill up in the METAL direction, again
in proportion to the strength of the signal or the drift.
(7) Zoom
It is used to magnify or reduce target signal graphs. By using this
feature, you can magnify smaller signal graphs and reduce the larger
ones to better examine them.
If you wish, you can change the zoom scale with the up and down
buttons.
(8) 3D Detection Ground
During searching you can observe the following on the 3D detection
ground :
* All movements of the search coil - left, right, up and down,
* The total scanned area,
INVENIO has 2 detection screens: One with, and one without the
IPTU sensor. The screen with the sensor, will only function fully, when
the IPTU sensor is attached to the device, and it is turned on. If the
detection screen with the sensor is used while the sensor is not
turned on, the device will detect targets and provide their IDs, however
the advanced features (explained further in the manual) will not work.
The detection screen without the IPTU sensor on the other hand, can
always be used, regardless of whether the sensor is attached or not.
All modes, except for the Ground Anomaly & Cavity, will work in
both screens. The Ground Anomaly & Cavity mode will work in the
detection screen with the sensor only. Detection screen selection
does not have direct effect on the operation of the modes. The main
difference between the 2 screens is as follows: When searching in the
detection screen without the IPTU sensor, the device detects targets
and displays their IDs only. On the other hand, while searching in the
detection screen with the IPTU sensor, apart from the IDs, the device
also provides the instant depth, shape and 3D graphs of detected
targets.
DETECTION SCREEN WITH IPTU SENSOR
(1) Target ID Scale
Ranging from 0 to 99, this scale indicates which metal group the ID of
the detected target falls in. Each metal group is indicated by a different
color. For example, negative hot rocks and soil are shown by white
and brown colors, ferrous metals, such as iron, by red, and gold and
non-ferrous metals are indicated by yellow and green colors. When a
target is detected, the cursor will point to the target ID on the scale.
The IDs filtered by Discrimination and Notch Filter settings are shown
in black color on this scale. For more information please read the
sections about Target ID and Notch Filter.
(2) Magnetic Mineralization Indicator
Magnetic Mineralization Indicator ranges from 0 to 99. Upon start up,
the indicator will be empty and 0 will be displayed inside. Based on
the level of magnetic mineralization, this chart will fill up yellow and
the mineralization level will also be indicated numerically inside the
chart.
This measurement can be summarized as the level of magnetic
property and intensity of the ground. Simply, if you are working in an
area which contains intense and magnetized minerals, the level will
be high. If you are working on a less intense ground, the level will be
low.
This measurement is important from two aspects. First, on grounds
with high magnetic mineralization, search depth is low and users
should be aware of this fact. Second, magnetic mineralization is a
property which is particularly seen with mineralized rocks and this
* The length and width of the scanned area by zooming in and out on
ground image,
* The 3D graphs of all target signals with target separation according
to metal groups.
In addition, this advanced detection ground allows you to track back
your scan within a certain period of time and see the detected targets.
DETECTION SCREEN WITHOUT IPTU SENSOR
The functions of the target ID scale, the magnetic mineralization
indicator, the ground balance window, and the Drift-Metal bar are
the same as those in the detection screen with the IPTU sensor. For
this reason, these are not explained again in this section. If you wish,
please read the section above titled ''Detection Screen with IPTU
Sensor''.
(1) Target ID Indicator
Upon target detection, the ID will be displayed here. It ranges from 00
to 99 and gives an idea to the user about what the target may be.
For more details on target ID, please read the relevant section of the
manual.
(2) Target Detection Screen
While searching, the signals, as well as the signal strengths of metals,
positive rocks, and positive drifts can be observed in this section.
The target signals are defined by different colors just like in the color
ID scale. Ferrous metals are shown in red, and non-ferrous metals are
with yellow and green colors. The signals of target IDs discriminated
out by Discrimination and Notch Filter settings are indicated with gray
color.
12
4 7 86 5
3
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Nokta Makro Invenio bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Nokta Makro Invenio in de taal/talen: Engels als bijlage per email.

De handleiding is 5.71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Nokta Makro Invenio

Nokta Makro Invenio Gebruiksaanwijzing - Türkiye - 36 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info