619088

Niko 350-20085 Handleiding

9
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
PM350-20085R15331 nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu EN
350-20085
9
Light level 20 50 100 200 300 400 500 700 1000 ∞ Learn
Number of times
that the red status
LED flashes
1 2 3 4 5 6 7 8 9 10 11
Finally, the red LED will once again flash three times to indicate the switch-off delay.
Switch-off delay puls 2 min 5 min 10 min 15 min 30 min 60 min
Number of times that the
red status LED flashes
1 2 3 4 5 6 7
Please check section 4 to change the mini detector’s settings
4. IR REMOTE CONTROL UNIT
You use the IR remote control unit (Fig. 5) to select another application, to perform a test or to enter other
parameters.
4.1. Settings keys
To change the mini detector settings:
1. Press
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
three times within five seconds to unblock the device.
The green status LED flashes twice by way of confirmation. The device is now in the settings mode.
2. Change the light level or the switch-off delay using the keys below. The red LED will flash to confirm that
the motion detector has received the signal from the remote control.
3. Press
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
once to re-block the device.
The green status LED flashes twice by way of confirmation. The changed setting is activated, and the
device works again according to the newly selected settings.
Note: If you do not block the device, it will be blocked automatically after one minute. All changes are
then automatically saved.
Key Function
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
Use this key to set the mini detector for use as a presence detector.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
Use this key to set the mini detector for use as an absence detector.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
- Use these red keys to set the desired light level (lux value).
- There are ten fixed lux values: 20, 50, 100, 200, 300, 400, 500, 700,
1000 lux and No lux (daylight dependent).
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
- Use this key to set the current light level in the room as the level at
which the lighting must be switched on.
- When you press this key, the red status LED flashes once to indicate
that the current light level has been loaded. If this light level is not
between 20 and 1500 lux, the minimum level (20 lux) or the maximum
level (1500 lux) is loaded.
Use this setting when the desired minimum light level in the room has
been reached. This is the time at which the lighting must be switched on
because the daylight level is no longer adequate.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse
2min 5min 10min
Memory
out
Clear
memory
30min60min15min
- Use these blue keys to set the desired switch-off delay.
- There are six fixed values: 2, 5, 10, 15, 30 and 60 minutes.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
If you press this key:
- The lighting remains switched on permanently for eight hours.
- The red status LED flashes (0.25 s on and 30 s
off).
- All other functions on the mini detector are blocked.
Press this key again to deactivate the function. The red status LED stops
flashing. The mini detector is returned to automatic mode. You can now
switch on the lighting again according to the selected application.
You cannot switch off this function using a push button.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
With this button you can store the most recently selected settings (light
level and switch-off delay that were last set) into the memory of the IR
remote control.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
Press this key to send the saved settings to the mini detector.
This key is handy for setting the same parameters on various mini
detectors simultaneously.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
This key erases all settings from the memory of the IR remote
control unit.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
The device is returned to the factory settings.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
The detection range is tested by activating the integrated motion sensor by
way of a walking test:
- The lighting is switched on for five seconds, and the red status LED
flashes when the test mode is activated.
- The lighting is switched on for five seconds, and the red status LED
flashes every time the sensor detects activity.
The test mode is closed in one of the following ways:
• Press
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
on the IR remote control unit.
• Press
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
on the IR remote control unit.
• Briefly press the connected push button.
After this, the mini detector will again work according to the selected
settings.
During the walking test, the light sensor does not work.
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
This button gives the same result as a short push on the connected push
button (see section 3.2.).
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
This button gives the same result as a long push on the connected push
button (see section 3.2.).
4.2. Function keys
Key Function
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
If you press this key, the device indicates what the current settings are by
way of the red status LED. The green status LED indicates the start status.
First, the green status LED flashes, and then the red status LED indicates
the status. The first time that the red status LED flashes, it indicates the
preset light level. The second time it indicates the switch-off delay (see
section 3.3.).
For example: The mini detector is set to 300 lux and 10 minutes. Press
insert symbol: the green status LED flashes once and the red status LED
five times (= 300 lux), then the green status LED flashes once more and the
red status LED flashes four times
(= 10 min).
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
You switch the light on or off permanently, regardless of the motion
detected or the light level. If this function is activated, the red status LED
flashes (0.25 s on and 10 s off).
The mini detector will remain in this function mode until you either:
• press
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
once
• press the connected push button briefly
• press
Lock/
unlock
Short
push
Learn actual lux
20
Lux
50
Lux
100
Lux
300
Lux
400
Lux
200
Lux
500
Lux
700
Lux
1000
Lux
No
Lux
Fact.
setting
Long
push
Test
On/Off
App.
Auto
App.
Active
Light
On/Off
Memory
in
Status
Time
30min60min15min
8
Hours
Pulse 2min 5min 10min
Memory
out
Clear
memory
three times within 5 s.
After this, the mini detector will again work according to the selected
settings. The red status LED flashes once by way of confirmation.
5. OPERATION AND USE
5.1. Initial use
Only attach the mini detector to a power supply after all of the cables have been connected. The mini detector
is ready for use approximately 40 seconds (warm-up time) after you have switched on the power supply.
While the device is warming up, the red indication LED will flash (0.25 s on and 2 s off) and the load will be
switched off for 40 s. Once the device is warmed up, the green status LED flashes twice in rapid succession.
5.2. General operation
The integrated light sensor continuously measures the daylight level in the detection area and compares this
level to the preset lux value. Thanks to the light sensor, the light switches on automatically only if the mini
detector detects motion within the detection range and if there is insufficient daylight present:
• The lighting remains switched on as long as motion is detected and as long there is insufficient
daylight present in the room.
• After the last motion is detected, the lighting remains switched on for the duration of the
preset switch-off delay (1 to 60 minutes). As soon as the switch-off delay has elapsed, the
lighting switches off.
• The lighting also switches off automatically as soon as the level of daylight is sufficiently high,
even if at that moment there is still motion detected in the room.
5.3. Detection range
You can expand the detection range by connecting two mini detectors (350-20085) in parallel (master-master
arrangement) (also see Fig. 1). These mini detectors each control the lighting according to their own settings.
They have the same detection range (circular with a diameter of 9.5 m). In order to cover an entire area with
several detectors, we recommend that you take into account an overlap of approximately 30% (Fig. 6). In the
case of a master-master arrangement, the mini detectors function optimally in rooms with little or no daylight.
5.4. Examples of applications
Example 1: Attic
Operation of the absence detector:
• The lighting is automatically switched off, after a preset time period (switch-off delay), if the mini
detector does not detect any more motion in the detection range or if the ambient light level exceeds the
preset lux value for a period of five minutes.
• You can only switch on the lighting again manually by briefly pressing the push button. If there is sufficient
light in the room, the lighting will however not be switched on by a short push on the button. You can also
manually switch off the lighting (= eco-off).
• In addition, you can also press and hold the push button, which is recommended in situations when the
lighting must be switched on or off for longer periods of time:
… 9 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Niko 350-20085 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Niko 350-20085 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 8,73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info