Handleiding Multiplex ROYALevo7 (pagina 51 van 77) (Engels)

30268

Verklein

Vergroot

Pagina terug

1/77

Pagina verder

ROYAL evo 7

Page 50

18.4. Sub-menu: Flight phases

Flight phases are groups of settings (data) which can be

called up for a particular model by operating a switch.

The settings can be optimised for different flight tasks.

For each flight phase you can adjust the transmitter

control settings individually to suit the requirements of

the model (e.g. reduced travels for SPEED, extended

flaps for LANDING, different collective pitch and throttle

curves for model helicopters, …). All the settings which

can be modified for the various flight phases are as-

signed the code numbers 1 … 3 or 4 associated with the

flight phase (Î 14.). The ROYALevo7 also features flight

phase specific digital trims (Î 12.), i.e. the trims can be

set separately for each flight phase, and the settings are

stored permanently. This simply means that the model

is always perfectly trimmed in each flight phase.

For fixed-wing model aircraft we have provided three

flight phases. Flight phases 1 … 3 are selected using

switch J: “F-PH 1-3”.

For model helicopters an additional fourth flight phase

is provided for auto-rotation. This is selected using

switch I “A-ROT”, and always has highest priority. This

means: the auto-rotation flight phase

AUTOROT is al-

ways activated when switch I “A-ROT” is operated, re-

gardless of the flight phase 1 …3 currently selected us-

ing switch J “F-PH 1-3”.

The transition between flight phases is “soft” (it takes

about one second), in order to avoid sudden servo

movements when the change-over is made. The excep-

tion to this rule is the auto-rotation flight phase with

model helicopters. If you operate switch I “A-ROT”, the

transition to the

AUTOROT flight phase occurs immedi-

ately.

The Flight phase menu for a fixed-wing model may look

like Fig. 1; for a helicopter like Fig. 2:

Fig. 1 Fig. 2

Fig. 1 contains the following information:

x The first column shows the number of the flight

phase, followed by the name of the flight phase

x Flight phases 1 and 3 are blocked

(names crossed out)

x Flight phase 2

NORMAL is currently active

(

x after the name)

x The flight phase switch is

J> on the right-hand side.

The same applies to the four helicopter flight phases

shown in Fig. 2.

18.4.1. Selecting names for flight phases

The following flight phase names are available:

NORMAL, START1, START2, THERMAL1, THERMAL2,

SPEED1, SPEED2, CRUISE, LANDING, HOVER, 3D, ACRO

The name serves only as information to the user. The

number of the flight phase is crucial to its properties, i.e.

flight phases of the same name do not necessarily share

the same settings or characteristics.

This is the procedure for changing a flight phase

name:

Use the UP / DOWN buttons (▲ / ▼ ) or one of the two

3D digi-adjustors to select a flight phase, and confirm

your action by pressing the ENTER button or one of the

3D digi-adjustors  the cursor jumps to the name input

field.

You can now select a suitable name using the UP /

DOWN buttons (▲ / ▼ ) or one of the two 3D digi-

adjustors.

Press the ENTER button or a 3D digi-adjustor to con-

clude the procedure. Note: this requires a double press

if you have changed the name of the currently active

flight phase.

Exception

The name for flight phase 4 for helicopters is

AUTOROT,

and this cannot be changed.

18.4.2. Blocking / releasing flight phases

You can release or block any flight phase using the

REV/CLR button. By blocking a flight phase you can

eliminate the danger of launching a model after acci-

dentally selecting a flight phase which does not contain

the correct settings.

If you select a blocked flight phase using one of the

flight phase switches J (“F-PH 1-3”) or I (“A-ROT”), you

will hear a continuous warning sound. The last used

flight phase remains active, and its number is shown in

status display 2. The name of the blocked flight phase

which you have selected is shown crossed out.

This is the procedure for blocking / releasing flight

phases:

Select a flight phase, then press the ENTER button or

one of the 3D digi-adjustors to confirm your action 

the cursor jumps to the flight phase name. You can now

switch between “free” and “blocked

” using the REV/CLR

button.

Selecting another name using the 3D digi-adjustor also

releases a blocked flight phase.

Note:

The currently active flight phase (marked with

x) cannot

be blocked.

18.4.3. Copying flight phases

We recommend the following procedure if you wish to

make a start using different flight phases:

Begin with just one flight phase, leaving the other flight

phases blocked. Your model should now be test-flown

and all settings carefully optimised. The flight phase can

now be copied. When you switch to the new flight

phase(s) you can be confident that the model will be-

have in the usual manner. All you have to do now is

make the desired modifications to the copies.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Multiplex ROYALevo7 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Multiplex ROYALevo7

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info