475272
47
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
5. NetCommand IR Control (837 Series) 47
To perform this procedure, you need:
The remote controls for both the TV and the •
device you want to control.
An IR emitter cable available from Mitsubishi•
.
Note: To set up an A/V receiver, see “Setting Up A/V
Receiver Control,” page 52.
Connect and position the IR emitters for the
1.
devices you wish to control. See “IR Emitter Place-
ment on the opposite page.
Set the
2.
TV’s remote control to
TV
mode and power
on the TV.
Open the NetCommand
3.
Learn screen as follows:
If working from the • New Device Found screen
after the device is first detected, highlight
NetCommand and press
ENTER
to open the
Learn screen for the device.
If performing NetCommand setup at any time •
after the device has been recognized through
Auto Input Sensing:
a. Press
ACTIVITY.
b. Highlight the desired input icon and press
ENTER
to switch to that input.
c. Press
MENU
, highlight Inputs, and highlight
Learn to open the Inputs > Learn screen
for the device.
The first function highlighted in the
4.
Learn screen
is always Power On. Aim the TV’s remote control
at the TV and press
ENTER
to begin learning for that
function.
When the
5.
Power On
text starts flashing, aim the
device’s
remote control at the TV and hold the
POWER
key until a check mark appears next to Power On.
If the text stops flashing before the check mark •
appears, repeat the previous step.
To remove the key from NetCommand control, •
press the
CANCEL
key while the key name is
highlighted.
Press the
6.
keys on the TV’s remote control
to highlight other keys on the list. Repeat steps
4 and 5 for each additional function you wish to
control through NetCommand.
Note: Device keys in the far right column will be asso-
ciated with the remote control’s
MORE
key when
“learned.” See the table on page 49.
If the device has a separate
7.
POWER OFF
key, press
on the TV’s remote to highlight Power Off.
Repeat the earlier steps to “learn” the
POWER OFF
key.
If the device has no
POWER OFF
key, skip this step.
Press
8.
BACK
to finish NetCommand “learning” for the
current device.
From the New Device Found screen, highlight
NetCommand and press ENTER to open the Learn
screen.
Initial NetCommand Setup
Inputs > Learn screen
Key names marked with a
check have been “learned.
Device-specific keys in the
rightmost column can be accessed
with the MORE key after “learning.
Adding or Removing Device Keys from
NetCommand Control
Switch the TV to the device. Press
1.
ACTIVITY
, high-
light the devices icon, and press
ENTER
.
Open the
2.
Inputs menu and highlight the Learn icon.
When the
3.
Learn screen displays:
To add keys: • Continue as described earlier
under “Initial NetCommand Setup” on this
page.
To delete keys:• Highlight the name of the key
you wish to delete and press
CANCEL
on the
TV‘s remote control to clear the check mark.
47

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mitsubishi WD-65837 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mitsubishi WD-65837 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info