475272
46
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
46 5. NetCommand IR Control (837 Series)
The NetCommand system uses emitters connected
to the
IR
NetCommand Output
jack to control other
devices such as DVD players, cable boxes, satellite
receivers, and VCRs.
IR emitter cables are available for purchase from
Mitsubishi. Request either part number 242D483020
(two-ended cable) or part number 299P254020 (four-
ended cable).
Connect the plug end of the IR emitter cable to the
1.
IR—NetCommand Output
jack on the TV back panel.
When the
2.
New Device Found screen displays,
highlight EXIT and press
ENTER
.
The New Device Found screen displays when you
connect the IR emitter.
Position the emitter end with the emitter bulb facing
3.
the device’s remote control sensor. The bulb emits
infrared light in a cone-shaped pattern. Place the
bulb far enough from the sensor to allow the cone
pattern to reach the sensor.
In some cases, the emitter works better facing
downward from the top of the device. Experiment
to find what works best.
Secure the emitter ends in place using double-
4.
sided tape.
Place any unused ends behind the devices to
5.
prevent stray signals from reaching the IR sensors.
1
2
3
HDMI
AVR
AUDIO
OUTPUT
L
R
Pb
Y/ VIDEO
Pr
Pb
Pr
INPUT 2
INPUT 1
DIGITAL
AUDIO
OUTPUT
DVI/PC
AUDIO
(480i / 480p / 720p / 1080i)
L
R
L
R
INPUT
AUDIO
Y/ VIDEO
3D
GLASSES
EMITTER
ANT
IR-
NetCommand
Output
R
1
2
3
HDMI
IR-
NetCommand
Output
R
IR-
NetCommand
Output
R
TV Main
Panel
DIGITAL
SURROUND
S
CH
A/V Receiver
Other A/V Device
1.
3.
2.
2.
3.
Connecting IRNetCommand Output
In front of a
single average-
sized device
On top of a single
tall device
In front, shared
by two average-
sized devices
IR sensor
IR sensor
IR sensor
IR sensor
In front of a single
average-sized device
On top of a single tall
device
In front, shared by two
average-sized devices
IR sensor
IR sensor
IR sensor
IR sensor
IR sensor
In front of a single
average-sized device
On top of a single
tall device
In front, shared by
two average-sized
devices
IR sensor
IR sensor
IR sensor
IR sensor
IR sensor
Place IR emitters so the signal can be “seen” by the IR
sensor on each device.
If You are Unable to Locate
a Device’s IR Sensor
The IR sensor is usually behind the plastic window •
of the front display panel. Using a flashlight, you
may be able to see it as a round or square cutout.
If you cannot see the sensor and the device’s •
Owner’s Guide does not specify the location, do
the following using the devices remote control.
Starting at one end of the plastic window, hold 1.
the device’s remote control about one-half
inch from the front of the device and press the
POWER
key.
If the device does not respond, move the 2.
remote control one inch toward the center and
try again. Repeat until the device responds.
Repeat the previous steps starting at the other 3.
end of the window. The sensor will be between
these two points.
IMPORTANT
Position IR emitters so that each device’s
sensor “sees” the signal from only one emitter.
Otherwise, a device receiving signals from
multiple sources (remote controls, IR emitters)
may not respond at all.
IR Emitter Placement
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mitsubishi WD-65837 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mitsubishi WD-65837 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info