475319
32
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
32 Chapter 2. Connecting
Connecting the IR Emitter NetCommand
®
If a single emitter end can be placed in a
position that will operate more than one device,
do not use a separate emitter end for the
additional device. A single device receiving
remote control signals from too many emitters
or remote controls may not respond at all.
IMPORTANT
IR Emitter NetComman
Figure 15
An IR emitter cable is included with the TV.
The emitters connected to these jacks are used by the
NetCommand system and by TV Guide On Screen® to
control other devices such as VCRs, DVD players, Cable
boxes and Satellite receivers.
1. Connect the plug end of the supplied IR Emitter
Cable to either one of the IR Output NetCommand
jacks on the TV back panel.
2. Run the cable for each of the emitter ends under,
alongside, or over the top of each device to be
controlled to the area of the front where the remote
control sensor is located.
3. Place the emitter end in front of the remote control
sensor of the device to be controlled. The emitter
bulb should face the remote control sensor. This bulb
emits infrared light in a cone shaped pattern. The
bulb needs to be placed far enough from the remote
control sensor to allow the cone pattern to include
the sensor.
The remote control sensor is usually behind the
plastic window of the front display panel. It is
sometimes visible when you look through the display
plastic using a flashlight and is normally a round or
square cutout behind the plastic. If you cannot see
the sensor and the device’s Owner’s Guide does
not specify the location, you can find it by using the
device’s remote control.
a. Hold the remote about one-half inch from the
front of the device. Starting from one end of the
display window plastic, press the POWER button.
b. If the device does not respond, move the remote
control one inch toward the center and try again.
c. Repeat this until the device responds.
d. Note this location and then start over from the
other end of the display window plastic, repeating
until the device responds again.
The remote control sensor will be somewhere
between these two positions. This is usually
enough accuracy for the placement of the IR
emitters.
• Withsomedevices,theemitterworksbetterfacing
downward from the top of the device. Some
experimentation may be needed.
• Theemitterendbeingusedcanbesecuredinplace
using double stick tape.
• Ifyouarenotgoingto
be using all emitter ends, place
the unused ends behind the devices so that they
cannot send signals to the remote control sensors.
$0.10/&/5
:1C1SJQQJ
*/165
47*%&0
7*%&0
"6%*0
-&'5
.0/0
"6%*0
3*()5
%57$"#-&
7)'6)'
/FU$PNNBOE
*3&.*55&3
¸
(-JOL
¸
64&8*5)
$BCMF$"3%
"/5."*/"/5"69
57
%*(*5"-
463306/%
4
$)
"73FDFJWFS
0UIFS"7EFWJDF
0UIFS"7EFWJDF





Figure 15. Connecting IR Emitter NetCommand
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mitsubishi WD-62628 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mitsubishi WD-62628 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info