625622
14
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
14
ENGLISH
ENG
Removing the tool:
Turn tool lock (3) in direction indicated by arrow (a)
and remove the tool (b).
8.8 Tool change with keyless chuck
Use the keyless chuck when non-impact drilling in
metal, wood etc. and driving screws.
Chucking the tool:
Turn sleeve towards UP, OPEN" (a). Insert tool as
deeply as possible (b) and turn sleeve in the
opposite direction, until the noticeable mechanical
resistance is overcome.
Caution! The tool is not
yet clamped!
Keep turning the sleeve
(it must "click" when
turning)
until it cannot be turned any further -
only
now
is the tool
securely
clamped.
With a soft tool shank, retightening may be
required after a short time of drilling.
Removing the tool:
Turn sleeve towards UP, OPEN" and remove the
tool (4).
Note:
The ratchet sound which can possibly be
heard after opening the drill chuck, is functional
and is switched off by a reverse rotation of the
sleeve.
If the chuck is extremely tightened:
Unplug. Hold drill chuck with an open end spanner
at the flats on its head and turn the sleeve (4) hard
towards "AUF, RELEASE".
Only moderate pressure is required for hammer
drilling and chiselling. Exerting a high force does
not increase performance.
When drilling deep holes, remove the drill bit
periodically from the hole to release the stone
dust.
Drill tiles and other brittle materials without impact.
Keyless chuck cleaning:
After prolonged use hold the chuck vertically, with
the opening down, and fully open and close it
several times. The dust collected falls from the
opening. The application of cleaning spray to the
jaws and jaw openings at regular intervals is
recommended.
The vent slots of the machine should be cleaned
from time to time.
If the trigger (12) can not be depressed, check to
see that the direction of rotation selector switch
(10) is fully set to the R or L position.
Electronic signal indicator (9) with VTC
electronics
Rapid flashing - restart protection
(UHE 26 Multi, UHE 28 Multi)
When power is restored after a power supply
failure, for reasons of safety the still switched-on
machine will not start. To continue operation
switch the machine off, then on again.
Slow flashing - carbon brushes worn
(UHE 26 Multi, UHE 28 Multi)
The carbon brushes are almost completely worn.
If the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorized service centre.
LED on permanently - overload (UHE 28 Multi)
The motor temperature is too high. Relieve the
machine of the overload condition. If the overload
condition continues, the machine will stop. Switch
the machine off and on again, then let it cool down
at no-load running.
f
Use only genuine Metabo accessories.
If you need accessories, check with your dealer.
For the dealer to select the correct accessory, he
needs to know the exact model designation of
your power tool.
9Tips and Tricks
10 Maintenance
11 Trouble Shooting
12 Accessories
17026949_0610 UHE 28 UHE 26 UHE 22 Multi.book Seite 14 Donnerstag, 10. Juni 2010 1:07 13
14

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Metabo-UHE-28-Multi

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo UHE 28 Multi bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo UHE 28 Multi in de taal/talen: Alle talen als bijlage per email.

De handleiding is 4,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info