625622
13
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
ENGLISH
13
ENG
8.2 Switching on/off
To start the machine, press the trigger (12).
The speed can be changed at the trigger.
The electronic soft start continuously accelerates
the machine up to the pre-selected speed
(machines with VTC electronics UHE 26 Multi,
UHE 28 Multi only).
For continuous operation the trigger can be locked
with the lock button (11). To stop the machine,
press the trigger again.
If switched on continuously, the machine
continues running if it is jerked out of your
hands. Therefore, always hold the
machine with both hands on the handles, stand
safely, and concentrate on your work.
8.3 Speed preselection
Depending on the application, the optimum speed
is preset with the pre-selector wheel (8).
8.4 Operating mode selection
Select the desired operating mode by turning the
control knob (13). To turn, push the stop (14).
Twist drilling 1st gear
(high torque)
Twist drilling 2nd gear
(high speed)
Hammer drilling
(only with use of hammer drill chuck)
Chiselling
(only with use of hammer drill chuck)
In chisel mode the chisel is locked to be twist-
proof. To position the chisel for the particular
application, set the control knob (13) between
and .
When a chisel is fitted, only operate the
machine in the chiselling operating mode.
.
Avoid levering movements of the machine
when a chisel is fitted.
8.5 Selection of direction of rotation
Do not actuate the rotation selector
switch (10) unless the motor has
completely stopped.
Select direction of rotation:
R = clockwise
L = counter-clockwise
8.6 Drill chuck change
When changing chucks make sure that
the spindle is clean. Grease spindle lightly
if required.
Removing the chuck:
Turn chuck lock (5) in direction indicated by arrow
against the stop (a) and pull it off the spindle (b).
Replacing the chuck:
Place chuck onto spindle (6) (a). Turn chuck
lock (5) in direction indicated by arrow (b) until
chuck slides fully onto the spindle, then release
the chuck lock.
Check to see that the chuck is properly seated.
Note:
To keep the spindle from turning while
changing chucks, set the control knob (13) to
chiselling.
8.7 Tool Change with SDS Chuck
Before fitting, clean tool shank and
apply special grease (accessories
order no. 6.31800)! Use only SDS-plus tools.
Inserting the tool:
Turn the tool while inserting, until it engages.
The tool is automatically locked.
17026949_0610 UHE 28 UHE 26 UHE 22 Multi.book Seite 13 Donnerstag, 10. Juni 2010 1:07 13
13

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Metabo-UHE-28-Multi

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo UHE 28 Multi bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo UHE 28 Multi in de taal/talen: Alle talen als bijlage per email.

De handleiding is 4,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info