625624
14
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
14
ENGLISH
ENG
Note:
To prevent the spindle from turning while
changing chucks, set the switch button (13) to
chiselling mode.
8.7 Tool change with SDS chuck
Before fitting, clean tool shank and apply
special grease (accessories order no.
6.31800)! Use only SDS-Plus tools.
Inserting the tool:
Turn the tool while inserting until it locks into place.
The tool is automatically locked.
Removing the tool:
Turn tool lock (3) in direction indicated by arrow (a)
and remove tool (b).
8.8 Tool change with keyless chuck
Use the keyless chuck when non-impact drilling in
metal, wood etc. and driving screws.
Chucking the tool
Turn sleeve (4) in the direction of "AUF, OPEN" (a).
Insert tool as deeply as possible (b) and turn sleeve
in the opposite direction, until the mechanical
resistance which can be felt is overcome.
Caution!
The tool is not yet clamped!
Keep turning the sleeve
(it must "click" when
turning)
until it cannot be turned any further -
only
now
is the tool
securely
clamped.
With a soft tool shank, retightening may be
required after a short drilling period.
Removing the tool:
Turn sleeve (4) in the direction of "AUF, OPEN",
and remove the tool.
Note:
The grating sound which may be heard after
opening the drill chuck is functional and is stopped
by turning the sleeve in the opposite direction.
If the chuck is very securely tightened:
Unplug.
Hold drill chuck using an open-end spanner at the
flats on its head, and turn the sleeve (4) vigourously
in the direction of "AUF, OPEN".
Only moderate pressure is required for hammer
drilling and chiselling. Applying a high degree of
pressure does not increase performance.
When drilling deep holes, remove the drill bit peri-
odically from the hole to remove dust.
Drill tiles and other brittle materials without impact.
Always keep the
safety coupling
(16)
clean and
free from dust.
Always keep the
spindle
(6) clean and apply a light
coating of grease. (for information on special
grease, see Accessories section: order no.
6.31800)
Keyless chuck (1)
cleaning:
After prolonged use hold the chuck vertically, with
the opening facing down, and fully open and close
it several times. The dust collected falls from the
opening. Regular use of cleaning spray on the jaws
and jaw openings is recommended.
Ventilation slits:
Clean the ventilation slits on the machine occa-
sionally.
If the trigger switch (12) cannot be depressed,
check to see that the rotation selector switch (10)
is fully set to the R or L position.
Electronic signal indicator (9):
Rapid flashing - restart protection
When power is restored after a power failure, the
machine - which is still switched on - will not start
for safety reasons. To continue operation, switch
the tool off and then on again.
Slow flashing - carbon brushes worn
The carbon brushes are almost completely worn. If
the brushes are completely worn, the machine
switches off automatically. Have an authorised
service centre replace the brushes.
b
a
b
a
9Tips and Tricks
10 Maintenance
11 Troubleshooting
17026909_0608 UHE KHE 28 Plus KHE Partner Edition.book Seite 14 Dienstag, 17. Juni 2008 3:51 15
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo KHE Partner Edition bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo KHE Partner Edition in de taal/talen: Alle talen als bijlage per email.

De handleiding is 6,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info