451400
9
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
function which results from improper use or unauthorized
modification from standard specifications, faulty
maintenance, damage or improper repair by anyone
other than qualified persons approved by Elektra Beckum
or its representatives.
Elektra Beckum reserves the right to change
specifications and design without prior notice and
without incurring obligation of any kind.
Equipment referred to as available or optional may
be at extra cost.
Contents
1 General
2 Specifications
3 Machine Installation
4 Blade Speed Selection
5 Band Saw Setup
6 Safety Rules
7 Additional Information
8 Connection to Power Mains
9 Optional Accessories
10 Dust Collection
11 Replacement Saw Blades
12 Electrical Wiring Diagrams
13 Spare Parts List Band Saw
3 Machine Installation
To facilitate better handling and prevent damage to
projecting parts during transport, this machine is shipped
partly disassembled. After unpacking the saw table, rip
fence and crank handle have to be installed before the
saw can be operated.
Remove wrapping and check for any visible damage
which may have occurred during transport. If damage is
detected notify your dealer immediately.
Remove rip fence carrier extrusion (201) from saw
table (200).
To install the saw band guard place bolts guides (91)
on carriage bolts M 8x30 (100), then slide assembly
into the table's T-slots. Place saw band guard left and
right (217/218) on the bolts and secure with washers
(108) and wing nuts (135) to table.
Slide 2 each carriage bolts M 8x30 (100) into the
table's T-Slots.
Place table onto the upper table trunnion (85).
Bolt to table trunnion with washers Ø 8.4 (108), spring
washers Ø 8.4 (111) and hex. nuts M 8 (114).
To reinstall rip fence carrier extrusion (201) to the
table, slide all four bolt guide into the table's T-slots
and tighten the wing nuts.
Press table insert (79) into the saw table. Use table
insert with wide slot (24) only for bevel cuts.
Insert bolt guide (90) with carriage bolt M 8x50 (101)
into the rip fence carrier extrusion's T-slot.
Place rip fence carrier (88) onto carriage bolt (101)
and secure with washer Ø 8.4 (108) and wing nut M
8 (135).
Attach rip fence extrusion (87) to rip fence carrier with
2 each carriage bolts M 6x40 (102), washers Ø 6.4
and knurled nuts M 6 (99).
Bolt the crank handle (70) to handwheel (20) with cap
screw M 5x55 (105) and a hex. flat nut M 6 (115).
Counter screw with the hexagon nut so it will not
loosen.
After assembly the table needs to be aligned to have the
blade running through the centre of the table insert's slot.
9
Table side alignment:
Loosen the mounting screws of the lower table trunnion
(84).
Move table trunnion to left or right, as required.
Tighten mounting screws, making sure the table stays
in the set position.
User Responsibility
This machine will perform in conformity with the
description contained in the instructions provided. This
machine must be checked periodically. Defective
equipment (including power cables) should not be used.
Parts that are broken, missing, plainly worn, distorted or
contaminated, should be replaced immediately. Should
such repair or replacement become necessary, it is
recommended that such repairs are carried out by
qualified persons approved by Elektra Beckum or its
representatives.
This machine or any of its parts should not be altered or
changed from standard specifications. The user of this
machine shall have the sole responsibility for any mal-
Setting table square to the blade:
For bevel cuts the table tilts from 90° steplessly
through 45°. Loosen the wing nut (135) on the table
trunnion (84) to adjust the table position.
Underneath the table a stop is installed, which rests on
the saw housing when the table is in the 90° position.
2 Specifications
Height x Width x Depth: 1920 x 845 x 745 mm
Weight: approx. 127 kg
Table height from floor: 926 mm
Throat capacity: 440 mm
Max. height of cut: 300 mm
Saw blade length/width: 3380/6-25 mm
Saw table: 550 x 720 mm
tilts from 90° through 45°
Blade speeds: 50 Hz 68-176-375-967 m/min
60 Hz 82-211-450-1160 m/min
Motors
1.1 kW/1.5 hp 115V 50/60 Hz 1-phase
1.1 kW/1.5 hp 220 - 240 V 50/60 Hz 1-phase
1.5 kW/2.0 hp 220V 50/60 Hz 3-phase
1.5 kW/2.0 hp 380 - 415/440 V 50/60 Hz 3-phase
Noise information according
to DIN 45635 idling under load
Sound power level: 85 dB(A) 90 dB(A)
Workplace related noise
emission value: 75 dB(A) 82 dB(A)
1 General
The BAS 500 band saw is used for cutting wood, wood-
like materials or plastic across the grain or longitudinally.
Make sure that you always use a band saw suitable for
the material to be cut.
In individual cases the machine can also be used to cut
other materials. Written permission from the company
Elektra Beckum AG (see the section below on product
liability/warranty for the address) is required in such
cases.
Only use the band saw in dry surroundings. Round
materials may only be cut using a suitable supporting
device.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo BAS 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo BAS 500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 2,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info