684269
16
Verklein
Vergroot
Pagina terug
1/504
Pagina verder
Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
Do not smoke near the fuel or the engine.
Do not put warm objects near the fuel or the engine.
Do not add the fuel when the engine is on.
Make sure that the engine is cool before you refuel.
Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
Tighten the fuel tank cap carefully or a fire can
occur.
Move the product at a minimum of 3 m (10 ft) from
the position where you filled the tank before a start.
Do not put too much fuel in the fuel tank.
Make sure that a leak cannot occur when you move
the product or fuel container.
Do not put the product or a fuel container where
there is an open flame, spark or pilot light. Make
sure that the storage area does not contain an open
flame.
Only use approved containers when you move the
fuel or put the fuel into storage.
Empty the fuel tank before long-term storage. Obey
the local law on where to dispose fuel.
Clean the product before long-term storage.
Remove the spark plug cable before you put the
product into storage to make sure that the engine
does not start accidentally.
General safety instructions for
maintenance
The operator of the product is responsible for the
performance of all necessary maintenance, as
specified in the operator's manual. Injury or death is
a possible result of incorrect maintenance.
Make sure that you regularly do the maintenance to
the product. The life of the product increases. The
risk of accidents decreases.
Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use
the product each day.
Only do the maintenance work that you find an
instruction about in this manual. An approved service
center must do all other maintenance work.
Have all product servicing done by an approved
dealer, not including the tasks in
MAINTENANCE on
page 18
.
Let an approved dealer or an approved service
center regularly examine the product to do
adjustments or repairs.
Make sure the product is correctly assembled.
Do not use the product if it is changed from its initial
specification.
Do not change a part of the product without approval
from the manufacturer.
Only use parts approved by the manufacturer.
Examine for broken or incorrectly aligned parts, and
parts that do not move freely. Examine for other
conditions that can have an effect on the operation
of the product.
Do not use a damaged product. Replace or repair
damaged components.
Keep caps and fasteners correctly tightened.
Replacement components that are not approved or
the removal of safety devices can cause damage to
the product. This can also cause possible injury to
the operator or bystanders.
Only use accessories and replacement parts as
recommended. Do not change your product.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
Obey the instructions for lubricating and changing
accessories.
Disconnect the spark plug cable before you
assemble the product, put the product into storage or
do maintenance.
If you cannot adjust the idle speed to make the
cutting attachment stop, speak to your service
center. Do not use the product until the product is
correctly adjusted or repaired.
Make sure the product is stable during transport to
prevent damage.
When not in operation, keep the product in a dry,
high or locked area away from children.
ASSEMBLY
WARNING: Read the safety chapter before
you assemble the product.
To assemble the handle
1. Remove the screws (A), washers (B), top clamp (D),
bottom clamp (E) and nuts (F) from the handle (C).
(Fig. 35)
2. Attach the top clamp (A), handle (B), washers (C)
and screws (D) to the top of the upper shaft.
3. Attach the bottom clamp (E) and nuts (F) to the
bottom of the upper shaft. (Fig. 36)
4. Put the assist handle between the 2 arrows on the
upper shaft.
5. Fully tighten the screws.
Note: Make sure the handle does not move.
16 860 - 001 - 28.10.2018
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw McCulloch B33 PS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van McCulloch B33 PS in de taal/talen: Alle talen als bijlage per email.

De handleiding is 5,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info