Make sure to hold the body with your hand touching the back plate.
6 Apply cotton to the skin and move the device slowly.
(Fig. 8)
Apply the cotton gently to the face and slowly move the device by sliding it from the
center of the face to the outer side.
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
The time for use is within 5 minutes.
Unless you apply cotton puff to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the head is not vibrating, the device is not working.
If you leave the device as it is for about 5 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
5 Hold the device with your hand touching the back plate of the body.
(Fig. 7)
Add more toner when there is no moisture in the cotton or when the device is
difficult to slide.
Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the Level
switch button and switch to "Low."
If you still feel your skin tingling, use the device by adding more toner.
CAUTION
8 Remove the ring and the cotton.
7 After 5 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
The finish sound (beep beep) will inform you.
Wipe off the surface of the head with a tissue.
Do not use the cotton again once it is used. It might cause problems with your skin.
Step 3 "BOOST"
(It is recommended that you use “BOOST” once a day for milky lotion or moisturizing
product once or twice a week for sheet mask.)
Fine vibrations and gentle switching of the electrode enhance the effect of milky lotion or
sheet mask.
Do not keep the cotton on the same area of skin, but move it
around. (Cause of problems with your skin or physical discomfort.)
1 Apply a gel-like moisturizing product or thick toner that you would normally use onto the
head and smoothen it over the entire head with your fingers. (Fig. 10)
When not using cotton
If you use a gel-like toner/moisturizing product (all-in-one type toner for moisturizing) or
thick toner which is difficult to permeate the cotton you can use this device without
attaching cotton to the body.
3 Choose "the strength" of electrical potential with the Level switch button.
Switch the "strength" with the Level switch button according to the condition of your skin.
Do not keep the head in the same area of the skin, but move it
around. (Cause of problems with your skin or physical discomfort.)
2 Press the power switch. (Fig. 9)
The Level indicator lamp will be turned on, and the "MOISTURISE" on the mode
indicator lamp will start flashing.
When a lamp in another mode is flashing, press the mode switch button and switch
the mode.
When the "CLEANSE" mode is finished, press the power switch
and the "MOISTURISE" mode will automatically be set.
Every time the level switch button is pressed, the high and low in the electrical
potential will be switched. There will be no change in vibration strength.
The memory function memorizes the "strength" when the power has been shut off.
4 Hold the device with your hand touching the back plate of the body.
(Fig. 7)
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "Low."
Make sure to hold the body with your hand touching the back plate.
5 Apply the head directly to the skin and move it slowly.
(Fig. 8)
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
The time for use is within 5 minutes.
Unless you apply the head to your skin while touching the back plate, the device will
not vibrate. (skin sensing function)
If the head is not vibrating, the device is not working.
If you leave the device as it is for about 5 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
CAUTION
Add more toner or other moisturizing product when the head does not easily slide.
Apply the cotton gently to the face and slowly move the device by sliding it from
the center of the face to the outer side.
Do not apply the device on the same area of skin for more than 10 seconds.
If you feel your skin tingling by micro current while using the device, press the Level
switch button and switch to "Low." If you still feel your skin tingling, use the device
by adding more toner or other cosmetics.
6 After 5 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
The finish sound (beep beep) will inform you.
7 Wipe off the moisturizing product on the head and the body of the device with a tissue.
Moisturizing product
1 Place the sheet mask on your face or apply your regular milky lotion or moisturizing
product over your face evenly.
Wipe off the milky lotion or moisturizing product on your hands.
When the "MOISTURISE" mode is finished, press the power switch and the
"BOOST" mode will automatically be set.
2 Press the power switch. (Fig. 11)
The level indicator lamp will be turned on, and the "BOOST" on the mode indicator
lamp will start flashing. When a lamp in another mode is flashing, press the mode
switch button and switch the mode.
3 Choose "the strength" of electrical potential with the Level switch button.
Switch the "strength" with the Level switch button according to the condition of your
skin.
Every time the Level switch button is pressed, the high and low in the electrical
potential will be switched. There will be no change in vibration strength.
The memory function memorizes the "strength" when the power has been shut off.
