785623
10
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
10 EN / SCM20 & SCM40 PWM User’s Manual
3.4 SPECIFICATIONS OF THE PV ARRAY
WARNING
When the PV array is exposed to light, it
supplies a DC voltage to the Solar
Chargemaster which can be dangerous to touch.
For this reason, use of an external DC-switch is
strongly recommended. Alternatively, before
attempting any maintenance or cleaning the PV-
array should be protected from light exposure,
e.g. by covering the PV modules.
CAUTION!
Do not connect Solar Chargemasters in parallel
on the side of the PV array.
The Solar ChargeMaster is appropriate for nominal 12V
and 24V solar systems. The table shows the number of
cells required for the nominal voltages.
Battery voltage U
NOM
= 12V
Model Panel type Max input
voltage Max input
current
SCM20 PWM 36 cells 28V 20A
SCM40 PWM 36 cells 28V 40A
Battery voltage U
NOM
= 24V
Model Panel type Max input
voltage Max input
current
SCM20 PWM 72 cells 55V 20A
SCM40 PWM 72 cells 55V 40A
CAUTION!
Never connect voltages higher than specified to
the PV-input, as this will cause permanent
damage to the Solar Chargemaster.
Configuration examples for PV-arrays consisting of
monocrystalline or polycrystalline PV-modules:
3.5 CONNECTION OF LOADS
Depending on the energy system in which the Solar
Chargemaster is used, there are two options to connect the
electrical load to the Solar Chargemaster:
To the Load output on the Solar Chargemaster, or
Directly to the battery.
3.5.1 Load connected to the Load output
See Figure 5 for a typical installation diagram. The Load
output is provided with a protection circuit that switches off
the connected load automatically in case of overload or if
the battery voltage is too low. This kind of installation is
typically used when the PV-modules are the only source of
electrical power to charge the battery.
3.5.2 Load connected to the battery
If the maximum load will exceed 20 Amps (SCM20 PWM),
40 Amps (SCM40 PWM) or if the battery will also be
charged by other energy sources, such as a battery
charger or an alternator, the electrical load shall be
connected to the battery directly. See Figure 6 for a typical
installation diagram. In this situation the battery is no longer
protected against too low battery voltages. Installation of
additional undervoltage protection circuits may be
necessary. See section 5.3 for ordering information
3.6 THINGS YOU NEED
Make sure you have all the parts you need to install the
Solar Chargemaster:
Solar Chargemaster (included);
Battery temperature sensor with cable and plug
(optional, not included; see section 5.3 for ordering
information);
DC cables to connect the Solar Chargemaster; see
section 3.3 for specifications;
DC-fuse holder with a DC-fuse, to be integrated in the
positive DC-cable to the battery; see section 3.3;
Screws / bolts (Ø 4mm max.) (with plugs) to mount the
Solar Chargemaster to a surface;
Batteries;
Appropriate and reliable cable terminals, strain reliefs,
battery terminals and boot lace ferrules.
We recommend as a minimum tool kit:
Phillips screw driver nr.2 or flat blade screw driver 5
mm to fix the DC-cables;
Tools to fix the screws / bolts with plugs to mount the
Solar Chargemaster to a surface;
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mastervolt Solar ChargeMaster SCM20 PWM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mastervolt Solar ChargeMaster SCM20 PWM in de taal/talen: Engels als bijlage per email.

De handleiding is 0.73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info