Handleiding Marantz SR-18EX (pagina 33 van 47) (Engels)

6546

Verklein

Vergroot

Pagina terug

1/47

Pagina verder

ENGLISH

3. Press the command buttons in the desired sequence. When you

press a command button to be learned into the macro sequence,

its name will appear within the LCD window. Every time you

press another remote command, the macro step number

increases one by one.

4. It is possible during macro programming to adjust the timing of the

interval between several macro steps. Using the cursor keys ⁄6, the

interval between macro playback steps can be increased or

decreased in 1/2 second steps, over the range beginning at 1/2

second up to 10 seconds. For example, when the indicator shows

“0.5 SEC”, if you press the direction key, the interval time would

change to 10 seconds, then with another press of the direction

key, it would change to 9.5 seconds, etc. Use the direction key to

increase the interval time, and use the direction key to decrease

the interval time.

Some equipment may not be able to receive infrared commands in

one-half second steps. If after programming a macro you find that

the sequence was not properly carried out, you may wish to

experiment with different sequence timings to obtain the correct

operation results by using the adjustment method described

above.

Within each macro button, up to 20 steps can be memorized. In

the event that you wish to memorize more than 20 steps per

macro, then press another MACRO button n , and follow the

above operations. A maximum of 80 steps can be programmed

this way. However, you will probably find that 20 steps is more

than enough to carry out even the most complex macro

instructions to achieve a specific home theater operating result.

Note:

To memorize the cursor button ⁄6 except OK button, press and hold

the LIGHTING button ¤0 before pressing the cursor button.

When programming macro steps, note that the following buttons

would not normally be included in a macro sequence, and are

therefore not available for inclusion in a macro:

MODE z, MACRO x, CLONE c, PAGE ,, VOLUME ⁄1, MEMO ⁄3,

CLEAR ⁄4 and LIGHTING ¤0.

To check to see which MACRO buttons n have been programmed

with macros, at the beginning of the macro learning sequence the

four numerical (1 through 4) indicators at the bottom of the LCD

window will show a box around the number for each MACRO button

that already has a macro assigned to it (see Figure 11, which shows

that only MACRO button number 1 has a macro assigned to it).

Figure 11

In the event that you wish to revise a programmed macro sequence,

search the step number you wish to change by using the cursor

button and ⁄6, and then re-enter the new command. If you

memorized different commands than have already been

programmed, then the previous macro sequence will be erased and

re-written over with the new sequence. To add the new command,

press the MEMO button at your desired point. To delete the

sequence, press the CLEAR button at your desired point.

During macro programming, if a button is not pressed within 1

minute, the mode will automatically revert to the original mode (USE).

When you have completed the macro programming sequence, press

the MACRO x operation button with the the tip of a paper clip. The

“END” indication appears in the LCD display window. When you

release the MACRO button, all indications will revert to the initial

status.

There is one more important point to note about programming a

macro sequence. During a macro sequence, you may include more

than one function selection button to access some transport and/or

other commands. Depending on the macro sequence, this might

result in the amplifier or receiver’s function selection to be

inadvertently changed as well when the macro is played back. The

RC-18SR has a special feature to prevent this from occurring,

allowing you to access the special commands available under each

RC-18SR function button during a macro playback sequence, while

at the same time preventing the amplifier or receiver from constantly

switching its input source back and forth at the same time.

During the programming sequence, just remember that if you wish to

activate a specific input selector on your amplifier or receiver, make

sure that you press the desired input selection button FIRST.

Subsequent function button selections can be incorporated in the

macro sequence, but on playback, the RC-18SR will only send out a

function selection infrared command to the amplifier or receiver

based upon the first function command used in the macro sequence.

For example, you may wish to have a macro sequence which

activates the laser disc player input on your amplifier or receiver, and

then have additional commands in the sequence to instruct your TV

set to switch to an external video source to receive the laser disc

video signal. During the macro programming, make sure that you

press the LD function selector button BEFORE you press any of the

other function selector buttons in the sequence. You can then

include any of the TV commands by pressing the TV function selector

button, later in the sequence. When this macro is next used (played

back), the RC-18SR will send out the command to change the amplifier

or receiver’s input selector to laser disc input (since its function

selector button was the first one programmed into that macro

sequence), and will not subsequently change the amplifier or

receiver’s input to TV (but will send out any special TV commands that

you included in the macro sequence).

Programming a macro under a function selector key:

If you wish, you can also program a macro that can be activated by

pressing one of the function selector . keys. The programming

steps are similar to the steps outlined for programming a macro

number button n. The following example shows how to program a

macro under the LD (laser disc) function selector .:

(activate the main amplifier’s power on, switch the source to laser

disc, switch the amplifier’s surround mode to PRO LOGIC, switch on

the television, switch to the television’s AUX video input, power up the

laser disc player, and begin laser disc playback)

1. Press the MACRO x operation mode button with the tip of a

paper clip.

2. Press the LD function button ..

3. Press the following buttons:

POWER ON, LD, AMP, direct function D-2 (Dolby mode selector)

in page 1, TV*, SOURCE ON, direct function D-3 (VIDEO input

selector) in page 1, LD*, SOURCE ON, and PLAY.

4. Press the MACRO x button with the tip of a paper clip. The RC-

18SR will revert to the normal mode and save the macro under

the LD function button.

5. To execute the new macro sequence, press and hold the LD

function selector button for 3 seconds.

LOW

LEARN

NAME

2 3 4

Marantz SR-18EX Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info