Handleiding Marantz SR-18EX (pagina 31 van 47) (Engels)

6546

Verklein

Vergroot

Pagina terug

1/47

Pagina verder

ENGLISH

5. Continuing along, re-write the remaining letters “V”, “–”, “5”, “2”,

and “0”. By pressing the cursor keys and , each character is

confirmed in place. When you go to other DIRECT function

pages by using the page function keys ,, characters in the

previous page are also confirmed in place.

The name re-writing operation must be done on a function by

function basis, that is, re-write the names for all of the LD direct

functions, then switch to another function such as VCR, and

begin the re-writing process anew to re-name the VCR direct

function commands. After completing all re-writing of any of the

names, press the OK button within the cursor keys ⁄6.

How to re-write the STATUS name:

Using the same steps as outlined above, you can re-write the 9

character status name. During step 5 above, by pressing the up and

down cursor keys ⁄6 the left side of the status indicator begins

blinking, and you can change its display according to the same

method outlined above, using the 10 keypad character generator.

Remember, to confirm each character change, use the cursor keys

and . As above, when you change the direct function page by

pressing the page direction keys ,, this will confirm the re-written

characters in place as well for the page you just finished re-naming.

You have up to 9 letters, numbers or other characters available for

each status name.

How to re-write the DIRECT function button names:

You can change the name for each of the 8 direct function buttons by

using the steps described above to change main function name and

status name. Remember, each main function has 8 direct function

buttons on each of the 4 pages, so you have up to 32 direct functions

that can be re-named, if you wish, for each of the 11 main function

selection buttons .. You have up to 4 characters available for each

direct function button name.

After completing all re-writing of any of the names, press the OK

button within the cursor keys ⁄6, or switch to another function button

(such as CD). If, during re-naming, a button has not been pressed for

1 minute, the RC-18SR will revert to the prior operating mode (USE)

automatically.

If re-writing of all of the desired direct mode functions has been

completed, use the tip of a paper clip to press the operation MODE

button z, and select the “USE” mode. Now, all of the re-written

names are available for use.

How to clear (erase) the memorized codes

(and any re-written names):

The RC-18SR has a high capacity RAM, which ordinarily will allow the

learning of several hundred remote codes (and their associated new

names, if desired). However, due to the fact that some remote codes

occupy more memory space than others, it is possible that the

available RAM fills up completely, and the “FULL” indicator appears

in the LCD window. In this case, it will not be possible to learn any

new remote codes without first deleting some or all of the previously

learned remote codes and/or re-written names. There are 4 ways to

erase learned remote codes from memory:

n Erasing by button(s)

n Erasing by DIRECT button(s)

n Erasing by function(s)

n Erasing all memory contents (complete erasure)

•• Note that the factory-programmed RC-5 codes are not stored in

RAM, and are therefore not erasable.

For any of these memory erasure options, you must first set the RC-

18SR to LEARN mode.

Erasing the memory assigned to a particular button:

Press and hold the CLEAR button ⁄4 and press the button that you

wish to erase 2 times. The code previously learned by that button will

be erased, and will then be either empty, or the original factory

provided RC-5 code will re-appear in its place.

LOW

USE

NAME

2 3 4

5. Press and hold the corresponding SIDE-A button on the laser

disc player’s remote transmitter until the head of name blinks in

the RC-18SR LCD window or beep sounds emit. The RC-18SR

changes to the RENAME mode automatically as the next step. A

function name of the DIRECT function button blinks, you can

rename this blinking function name. You input the desired letter

or number with the ten keypad. (See the table in step 3 of the next

procedure for referece.) If you need not rename, press the OK

button or the other buttons except the ten keypad.

6. Now, proceed to program the other commands from the laser

disc player’s remote transmitter to the other DIRECT function

buttons (D2-D8). When you have “taught” all 8 direct functions

for Page 1, press the page direction key , to go to Page 2, and

you can program more direct function keys.

7. After memorizing all codes to all DIRECT function buttons, press

the operation MODE button z with the tip of a paper clip and

return the RC-18SR to the USE mode. Now, the newly memorized

codes are usable from the RC-18SR.

If you wish, you can re-write the names for each function name, status

name, and the direct function command names as follows:

For our example, you can change the LCD display window indication

from “LD” to “LV-520” (which is the model number for a Marantz laser

disc player). Remember, you can re-name a function selector button

with a new name of up to six characters of letters and numbers in any

combination.

1. Using the tip of a paper clip, press the operation MODE button z

until the NAME indicator appears and begins to blink in the LCD

window.

2. Choose a button that you wish to re-name, in this case, press the

“LD” function button .. In the LCD window, the first character of

the six function character display indicators starts blinking “A”,

which is the first letter of the alphabet if you press “1” button

twice.

3. Choose the desired letter or number by pressing the 10 keypad

buttons ⁄2. Each 10 keypad button has 4 characters attached to

it as follows:

10 keypad button Press, press again, press again, etc.

11 → A → B → C → 1 → ........

22 → D → E → F → 2 → ........

33 → G → H → I → 3 → ........

44 → J → K → L → 4 → ........

55 → M → N → O → 5 → ........

66 → P → Q → R → 6 → ........

77 → S → T → U → 7 → ........

88 → V → W → X → 8 → ........

99 → Y → Z → / → 9 → ........

00 → + → — →

SPACE

→ , → ’ → 0 ........

So, in the above example, by pressing the 10 keypad number 4 four

times, you get the letter “L” to appear in the display (see Figure 4).

Figure 4

4. You use the cursor buttons and ⁄6 to move to the next

character in the display. By pressing the right cursor button ,

the letter “L” is confirmed in the first character space in the LCD

window and the next character position begins blinking. If you

wish to erase a previously memorized character, position the

cursor over the character and put the SPACE character in its

place (the SPACE character is ten keypad number 0 pressed four

times, from the above character chart).

Marantz SR-18EX Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info