690911
19
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
19
WARNING:
Do not start the engine before the chain saw is completely assembled and
checked.
CAUTION:
Move at least 3 meters (10 ft.) away from the place where the chain saw is
fuelled.
Make sure you have a secure footing, and place the saw on the ground.
Make sure the guide bar and saw chain does not touch anything.
Do not forget to activate chain brake before starting the engine.
NOTICE:
Never pull the rope to the full extension.
Return the starter grip gently into the housing. Otherwise released starter grip
may hit your body or it may not rewind appropriately.
The engine must be put in idle immediately after starting. If not, the clutch can be
damaged, ask authorized service center.
Starting the engine
1. Activate the chain brake (lock).
2. Hold the front handle rmly with left hand and press the chain saw against the
ground.
3. Hold down the rear handguard with your right foot.
4. Start the engine in accordance with engine circumstances as follows.
Cold start
When the engine is not used just before starting, perform the following steps:
1. Push the primer pump several times until fuel comes into the primer pump. (In
general, 7 to 10 pushes.)
2. Move up the combination switch (choke position). This also actuates the half-
throttle lock.
3. Pull the starter grip slowly until feeling compression. Then pull it strongly. It may
take two to four attempts until engine res.
4. As soon as the engine res, move the combination switch to the middle (I)
position. Then pull the starter grip strongly again until the engine starts running.
5. Grasp the rear handle (the throttle trigger lock-out is released by the grasp) and
pull the throttle trigger for a little, and release it.
6. Release the chain brake.
Warm start
When the engine is used just before starting and still warm, perform the following
steps:
1. Push the primer pump several times until fuel comes into the primer pump. (In
general, 7 to 10 pushes.)
2. Move up the combination switch (choke position), and then back to the middle (I)
position.
3. Pull the starter grip slowly until feeling compression. Then pull it strongly. It may
take two to four attempts until engine starts. If the engine does not start, perform
the steps of cold start (see the section “Cold start”).
As soon as the engine starts running, grasp the rear handle (the throttle trigger
lock-out is released by the grasp) and pull the throttle trigger for a little then
release it.
4. Release the chain brake.
STARTING AND STOPPING ENGINE
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita EA3601F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita EA3601F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 12,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info