690911
18
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
18
Refuelling and relling chain oil
WARNING:
FOLLOW THE SAFETY PRECAUTIONS. Be careful and cautious when handling
fuels.
Switch off the engine.
CAUTION:
Clean the tank cap and the area around the tank after refuelling.
Refuel or rell the chain oil as follows:
1. Thoroughly clean the area around the caps, to prevent dirt from getting into the
fuel or oil tank.
2. Unscrew the cap and ll the each tanks with fuel (fuel/oil mixture) and chain oil
respectively.
3. Fill up to the bottom edge of the ller neck. Be careful not to spill fuel or chain oil!
4. Tighten the tank caps by hand as far as it goes.
Lubricating the chain
WARNING:
Check the chain oil tank only when the engine is switched off.
Make sure there is sufcient chain oil in the chain oil tank to provide good chain
lubrication during operation.
At medium oil feed rate, the oil tank capacity is approximately equal to the run time
of one tank of fuel.
Before operation or refueling, check the chain oil level and rell if necessary.
Adjusting the chain lubrication
WARNING:
Switch off the engine.
You can adjust the oil pump feed rate with adjusting screw. There are three degrees
of the oil pump feed rate, i.e. high, middle or low.
Adjusting screw locates at the bottom of the chain saw. Use a screwdriver and
adjust the amount of oil delivery appropriately.
Cleaning the oil guide
To ensure secure operation of the oil pump, clean the oil guide groove at the
housing and the oil feed hole in the guide bar regularly.
Checking the chain lubrication
CAUTION:
Never work with the chain saw without sufcient chain lubrication. Otherwise the
service life of the saw chain and guide bar is reduced.
Before starting work check the oil level in the tank and the oil feed.
Pay attention to the direction of the wind and avoid unnecessary exposure to the
oil spray.
Check the oil feed rate as follows:
1. Start the chain saw.
2. Hold the running chain saw approx. 15 cm (6”) above a trunk or the ground (use
an appropriate base).
3. If the lubrication is sufcient, you can see light oil trace because oil is scattered
off the chain.
NOTE:
After turning off the chain saw, it is normal that residual chain oil drips from the
oil feed system, the guide bar and the chain for a while. This does not mean a
defect. Place the saw on a suitable surface.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita EA3601F bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita EA3601F in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 12,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info