793624
20
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
20 ENGLISH
If you are repeating the wire tying processes in

from the switch trigger. Then, continue to operate
the switch trigger.
If you pull the switch trigger when there is no tie
wire left, an error is displayed. Replace with a new
tie wire and restart the tool.
Tying tips
Tilt the tool at a 45° angle against the crossed
rebars, and tie the wire in alternate orientations as

Fig.41
 
sections of crossed rebars.
Fig.42
 󰀩
orientation and perform tying twice so that tying
strength increases.
Fig.43
NOTICE: When you make the second tie, bend

tie. Otherwise, the wire may be repelled a second
time. It may cling to the tool tip, and the hook may be
damaged.
Replacing the tie wires
CAUTION: When you replace the wire, be sure
󰀨
the battery cartridge. Failure to do so may cause an
accident.
1. When wire has been used up, an error tone will
sound and error "1" will be displayed.
2. 󰀨
the battery cartridge.
3. Push the release lever, and lock it with the lock
lever.
Fig.44: 1. Release lever 2. Lock lever
4. Remove the wire reel from the tool.
NOTE: When wire has been used up normally,
approximately 20 cm of the wire remains wound on
the reel. In this state, replace the wire reel with a new
one.
󰀩
follow the steps below.
1. Insert the battery cartridge into the tool, and
turn the power on. The tool feeds the wire and cuts it
automatically.
2. 󰀨
the battery cartridge.
3. Remove the wire breaks using tools such as nip-
pers or pliers.
MAINTENANCE
CAUTION: Always be sure that the tool is
󰀨
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,

be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the cutter section
When the tool is used, dust and wire particles may
become adhered to the cutter section. In such a case,
clean the cutter section according to the following pro-
cedure. The cleaning should be done each time you use
up a box of reel. (50 pcs.)
Using the wire brush
1. Open the reel cover.
Fig.45: 1. Reel cover
2. Push the release lever, and lock it with the lock
lever.
Fig.46: 1. Release lever 2. Lock lever
3. Pass the wire brush through the guide.
When inserting the wire brush, hold it short and push it
into the guide little by little.
Fig.47: 1. Wire brush
Fig.48: 1. Gear 2. Guide 3. Wire brush
4. Push in the wire brush until its top end comes out
from the tip of the arm. And then pull out the wire brush.
This action is enough with one time.
Fig.49: 1. Arm 2. Wire brush
5. Close the reel cover.
Fig.50: 1. Reel cover
Using the air duster gun
Open the reel cover, push the release lever, and lock it
with the lock lever. Then bring the air duster gun close
to the guide and blow the air. Make sure the air comes
from the tip of the arm.
Fig.51: 1. Air duster gun 2. Guide
Cleaning with disassembly
If the cutter section is clogged or a wire is caught in it,
disassemble the parts and clean them.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita DTR181 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita DTR181 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens als bijlage per email.

De handleiding is 38.41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info