782325
15
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Technical and legal
information
MSTS1500-A by MacAllister
b) Never leave the table saw unattended when in operation. Turn if off and
don't leave the tool until it has come to a complete stop. An unattended
running saw is an uncontrolled hazard.
c) Locate the table saw in a well lit and level area where you can maintain
good footing and balance. It should be installed in an area that provides
enough room to easily handle the size of the workpieces. Cluttered, dark
areas, and uneven slippery floors invite accidents.
d) Regularly clean and remove wood shavings and saw dust from under
the saw table and/or the dust extraction unit. Accumulated saw dust is
combustible and may self ignite.
e) Secure the table saw. A table saw that is not properly secured may move or
tip over.
f) Remove tools, wood scraps etc. from the table saw before turning it on.
Distraction or possible jams can be dangerous.
g) Always use blades of the right size and with the appropriate mounting
hole (e.g. starshaped or round). Blades that do not match the mounting
hardware of the saw will run off-centre, causing loss of control.
h) Only use 10" saw blade with kerf width>2.3mm and blade body thickness is
1.8 mm match the riving knife with thickness of 2 mm.
i) Always use only a saw blade diameter in accordance with the markings
on the saw; Use only saw blades for which the maximum possible speed
is not less than the maximum spindle speed of the product.
j) Never use damaged or incorrect saw blade mounting means such as
flanges, saw blade washers, bolts or nuts. These mounting means were
specially designed for your saw, for safe operation and optimum performance.
Do not use any blunt , cracked, deformed or damaged saw blades. Only
replace the saw blade with one complying with the European standard
EN 847-1.
k)Never stand on the table saw, do not use it as a stepping stool. Serious
injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
l) Make sure that the saw blade is installed to rotate in the proper direction.
Do not use grinding discs or wire brushes on a circular table saw.
Improper saw blade installation or use of accessories not recommended may
cause serious injury.
5. Additional safety instructions
- These operating instructions are intended for people with basic technical knowledge
regarding the operation of a machine like this or similar electrical power tools.
Inexperiencend persons are strongly advised to seek competent advise and
guidance from an experienced person before operating this machine.
Getting started...
15
EN
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mac Allister MSTS1500-A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mac Allister MSTS1500-A in de taal/talen: Engels als bijlage per email.

De handleiding is 4.82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info