782325
12
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
b) Always use the guard and the riving knife for cuts. For cuts where the
saw blade cuts completely through the thickness of the workpiece, the guard
and other safety devices reduce the risk of injuries.
c) After finishing your work (e.g. seaming) where the guard and riving
knife have to be removed, immediately reattach the protective system.
The guard and the riving knife reduce the risk of injury.
d) Before switching on the power tool, make sure that the saw blade is
not in contact with the guard, the riving knife or the workpiece. Inadvertent
contact of these components with the saw blade could cause a hazardous
condition.
e) Adjust the riving knife as described in this instruction manual. Incorrect
spacing, position and alignment are possible reasons for failure of the riving
knife to effectively prevent kickback.
f) So that the riving knife can work, it must be positioned in the saw gap.
The riving knife is ineffective when cutting workpieces that are too short to be
engaged with the riving knife. A kickback by the riving knife cannot be prevented
under these conditions.
g) Use the appropriate saw blade for the riving knife. For the riving knife to
function properly, the saw blade diameter must match the appropriate riving
knife, the body of the saw blade must be thinner than the riving knife, and the
tooth width has to be greater than the thickness of the riving knife.
2. Safety instructions for sawing procedures
a) DANGER: Keep fingers and hands away from cutting area and
the blade. A moment of inattention while operating power tools or
slipping might cause your hand to get near the saw blade and may result in
serious personal injury.
b) Feed the workpiece into the saw blade only against the direction of
rotation. Feeding the workpiece in the same direction that the saw blade is
rotating above the table may result in the workpiece, and your hand, being
pulled into the saw blade.
c) Never use the mitre gauge to feed the workpiece for straight cuts and
do not use the ripping fence as a length stop when cross cutting with
the mitre gauge. Guiding the workpiece with the ripping fence and the mitre
gauge at the same time increases the likelihood of saw blade binding and
kickback.
d) When effecting straight cuts, always apply the workpiece feeding force
between the fence and the saw blade. Use a push stick when the distance
between the fence and the saw blade is less than 150 mm, and a push
block when this distance is less than 50 mm. Such "working aids" ensure
Technical and legal
information
MSTS1500-A by MacAllister
12
Getting started...
EN
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Mac Allister MSTS1500-A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Mac Allister MSTS1500-A in de taal/talen: Engels als bijlage per email.

De handleiding is 4.82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info