672421
11
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
English Operating manual
8
Note
If required, turn the lower drive
shaft slightly until the square shaft
and the holder of the upper drive
shaft mesh.
Tighten screw handle (1)
on the shaft coupling clockwise.
Check that the lower drive shaft
is tight.
Removal
Turn screw handle (1) on the shaft
coupling (2) anti-clockwise
to open the shaft coupling.
Press release button (3) and
pull the lower drive shaft straight
out of the shaft coupling.
Adjusting the carrying
system (shoulder strap)
Fig. 3
Place harness over your
shoulders.
Close the catch on the abdominal
belt (1.). If required, readjust.
Adjust abdominal belt
to the correct width (2.).
Adjust shoulder belt
to the correct length (3.).
Latch the hook of the carrying
system into the holder on the unit
(4.) and adjust the attachment
pad to a comfortable length (5.).
Note
Clip A is used in an emergency
to release the appliance as quickly
as possible from the carrying
system.
To do this, pull the clip upwards.
Attaching the cutting
attachment cover
Fig. 4
Unscrew the screws (1) and
remove the clamp (2) from
the cutting attachment cover (3).
Place cutting attachment cover
(3) on the lower drive shaft (4)
and attach the clamp (2) with
the screws (1).
Do not tighten the screws yet!
Remove screw (5) from the gear-
box.
Attach holder (6) to the gearbox
with the screw (5).
Tighten the screws (1).
Attaching/removing
the line head
Attaching the line head
Fig. 5
If attached, remove cutters
and blade attachment parts
beforehand. See “Removing
the cutting blade”.
Push spacer (1) onto the drive
shaft (2). Align the 3 openings
in the spacer (3), the gearbox (4)
and the gear cover (5).
Note
If alignment is not correct, the line
head cannot be attached/removed!
Insert retaining bar (6) through
the openings (3, 4, 5) in order
to secure the gearbox.
While holding the retaining
bar (6), turn the line head (7)
anti-clockwise (to the left)
onto the drive shaft.
Tighten line head firmly!
Note
Ensure that the line head (7)
is seated correctly on the spacer
(1), i.e. centred and resting flat!
Remove retaining bar from
the gear head.
Remove the line head
Fig. 6
Align the openings (3, 4, 5). Insert
retaining bar (6) through the
openings and hold in position.
Unscrew line head (7) clockwise
(to the right) off the drive shaft.
Attaching/removing the
cutting blade (depending
on model)
Attaching the cutting blade
Fig. 7
If attached, remove the line head
beforehand. See “Attaching/re-
moving the line head”.
Note
When attaching the cutting blade
for the first time, remove the blade
attachment parts (blade holder (8),
retaining bell (9), nut (10))
if attached. See “Removing
the cutting blade”.
Push spacer (1) onto the drive
shaft (2). Align the 3 openings
in the spacer (3), the gearbox (4)
and the gear cover (5) (Fig. 5).
Note
If alignment is not correct,
the cutting blade cannot
be attached/removed!
Insert retaining bar (6) through
the openings (3, 4, 5) in order
to secure the gearbox.
While holding the retaining bar
(6), attach the cutting blade (7)
with
blade holder (8), retaining
bell (9) and nut (10)
as follows:
Push cutting blade (7) onto
drive shaft (2) and centre
on the spacer (1).
Note
Ensure that the cutting blade (7)
is seated correctly on the spacer
(1), i.e. centred and resting flat!
Attach blade holder (8), retai-
ning bell (9) and nut (10).
Ensure that the blade holder is
seated correctly in the toothing!
Tighten nut firmly anti-clock-
wise (to the left) – tightening
torque 37 Nm.
Note
Before tightening, check again
that the cutting blade is seated
correctly.
If you do not have a torque
wrench, tighten the nut firmly by
hand. Then tighten the nut anti-
clockwise (to the left) another
half turn using a ring spanner.
Remove retaining bar from
the gear head.
Remove guard (if fitted) from
the cutting blade.
Removing the cutting blade
Fig. 8
Attach guard (if available)
to the cutting blade.
Align the openings (3, 4, 5).
Insert retaining bar (6) through
the openings and hold in position.
Unscrew nut clockwise (to the
right).
Remove cutting blade (7), blade
holder (8) and retaining bell (9)
(Fig. 7).
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw MTD BC43 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van MTD BC43 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van MTD BC43

MTD BC43 Gebruiksaanwijzing - Nederlands - 17 pagina's

MTD BC43 Gebruiksaanwijzing - Deutsch - 18 pagina's

MTD BC43 Gebruiksaanwijzing - Français - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info