568561
11
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
GB
ENGLISH | ADV-B40
11
BL- and BL+: This is for connecting the name tag lighting. Only LEDs
can be connected; make sure that the polarity is correct.
For the connected LEDs to light up, the brightness sensor must be
connected and shaded over.
Output: 12 V DC max. 60 mA
Bottom connection terminal (24-pole)
This terminal is for connecting the individual apartments. Up to four
internal units can be connected in parallel for each apartment. VIDEO1,
GND, +15V and AUDIO1 for apartment 1, etc.
Left connection terminal (4-pole)
LOCK- and LOCK+: This is for connecting the door opener. Some door
openers have a flyback diode fitted. If this is the case, make sure that
the polarity is correct. If the door opener only responds for a short
time (less than one second), its current consumption is too high. The
door opener should then be replaced with a model which uses less
current (maximum of 0.9 A). Alternatively a relay can be connected up
between the door opener and the terminal.
+15V and GND: This is for connecting the operating voltage.
You do not need to do this if you are using the recommended
star wiring.
Right connection terminal (4-pole)
This is for connecting an additional camera. Do not use the X module
with the VDV-500 Xcam, if the latter is used. The best thing is to cut the
cable to the camera just behind the X module. Then strip the insulation
from the cable. The three wires thus exposed are hooked up to the
connection: red to VCC, black to GND and yellow to Video. If you want
to use a camera from a different manufacturer, this must comply with
the following technical data:
12 V operating voltage, max. 500 mA current consumption, FBAS video
signal (1 Vpp, 75 ohm)
VCC is connected to the positive pole of the camera’s power connection.
GND is connected to the negative pole of the camera’s power
connection.
VIDEO is connected to the video output of the camera. On most
cameras, the negative pole is connected directly to the video ground. In
a few rare cases, the video ground also has to be connected to GND.
Please note that the camera is only supplied with power at this connec-
tion when the external camera is activated at the internal unit.
FITTING RECOMMENDATIONS
During fitting, the power supply should be switched off
to avoid short circuits.
The tech box must be attached in such a manner that rain water cannot
penetrate it.
The connection cables of the camera, loudspeaker and microphone
modules, as well as the brightness sensor, should not be extended. They
may however be shortened.
A 3 mm diameter hole is needed for the brightness sensor. The sensor
should be able to be retained in the hole of its own accord; if necessary
you can use hot glue or with an adhesive pad to fix it in position.
Adhesive pads designed especially for the camera, loudspeaker and
microphone modules, respectively, are included. You can use these to
secure those items at their desired locations. If you want to attach the
modules with screws, you should use the relevant module as template.
The loudspeaker and microphone modules should not be fitted directly
next to one another. This is to prevent feedback.
A hole with a diameter of 52 mm is needed for the camera module.
The camera has special markings to help ensure it is fitted correctly.
Given that the height at which the camera module is fitted depends
on local factors, we cannot recommend an optimum mounting height.
A mounting height of 1.5 m to 1.6 m has been a good rule of thumb
in the past.
For the automatic system to work properly, the light sensor should be
fitted at a location where daylight can reach it. If you want to fit the
light sensor to your existing front plate, a 3 mm hole will be needed.
See the drawings for the exact dimensions of the individual modules.
POSSIBLE SETTINGS
The outdoor station offers the following possibilities to set the system
to your personal circumstances:
Volume of the outdoor station
The potentiometer (9) is used to set the volume on the outdoor station.
To set the highest volume, turn the potentiometer carefully clockwise
as far as possible. Reduce the volume by turning in an anti-clockwise
direction.
VDV-B90+40_I-Manual_210x240_Fin3.indd 11 09.05.14 11:48
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ME ADV B40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ME ADV B40 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info