599356
14
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
$ENSfliV!TY
I
Figure
8 GRAYLINE
"orr"
Figure
9
PROPER SETTING
8= ENABLE DIGITAL
AVERAGING
9= DISABLE DIGITAL AVERAGING
The
digital
sonar in the X-50 is a
highly
sensitive sonar that
gives
extremely rapid updates
of the water
depth.
Under most
conditions,
the
bottom contour
changes
so
rapidly
that the
depth display
can
appear
to
"jitter".
In other
words,
the
display
will
change
the
depth
so
quickly
that it
can be difficult to determine the actual bottom
depth.
To alleviate this
situation,
the X-50 can
average
the bottom
readings
and
place
the result
on the
display.
When the X-50 is first turned
on,
averaging
is enabled. To
disable
averaging, press
the 9
key
once the menu
appears.
To enable
averaging
once
again, press
the 8
key.
10
=
BATTERY BACKUP ENABLED
11
=
BATTERY BACKUP DISABLED
The X-50
has
battery
backed
up
memory
which allows it to retain all
settings
even if the
power
cable is removed from the unit. The
battery
can
be turned off or
back on at
anytime.
When the X-50 is
shipped
from the
factory,
the
battery
is turned on. To
turn it
off, press
11. To turn it on
again,
press
iO.
I
stow
STOP
FAST
[
RECALL
RESUME
STORE
CHART SPEED
When the X-50 is
turned on for the first
time,
the chart scrolls at
a
pre-determined speed.
If a
higher speed
is
desired, press
and hold the
FAST
key
in the CHART
section of the
keyboard
until it runs at the desired
speed.
To slow the
display, press
and hold the SLOW
key.
Whenever either
of these
keys
are
pressed,
the
sensitivity
bar at the
top
of the
display
will
change
to a dashed
line and the word "CHT" will
replace
the word
"AUTO" near the
top
of the
display.
The dashed bar
represents
the chart
speed.
If
you press
and hold the FAST
key
for
example,
the
bar will start
moving
to the
right, signifying
that the chart
speed
is
increasing.
There are
10
steps
of chart
speed.
When the horizontal bar
reaches the
far
right
side
of the
screen,
the chart
speed
is at its maximum
value. The X-50 will
"flutter"
signifying
the maximum chart
speed
has been reached.
lithe automatic mode or
digital
function is
on,
the maximum chart
speed
cannot be attained.
(The
chart bar will
stop
two
steps
from
the far
right
and the audible tone will
"flutter".) Turning
both the
digital
and the
automatic mode off will allow
the maximum chart
speed
to be attained.
(Ten steps
of chart
speed
are available if the
digital
and AUTO are
off,
Eight
steps
of charts
speed
available
with
digital
and AUTO
on.)
12
=
SCALE ON
13
=
SCALE OFF
The
upper
and lower limit numbers on the
right
side of
the
display
can
be turned on or off
as desired. When the X-50 is
shipped
from the
factory,
the scales are turned on. To turn
them
off,
press
13 after the
menu
appears.
To turn
them
back on
again, press
12.
14
=
CALIBRATE SPEED
Due to
variations in boat hulls
and sensor
mounting locations,
the
speedometer
on the X-50
may
need to
be calibrated. The X-50
allows
corrections to be
entered
using
the CALIBRATE
SPEED command.
To use
it,
press 2nd,
DISC
(COMMAND)
until the
CALIBRATE SPEED function on
the menu
appears.
Then
press
14.
12
33
PDF compression, OCR, web-optimization with CVISION's PdfCompressor
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Lowrance X-50 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Lowrance X-50 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info