Handleiding Korg KingKorg (pagina 18 van 116) (Duits, Engels, Frans, Spaans)

707401

Verklein

Vergroot

Pagina terug

1/116

Pagina verder

KingKORG Owner’s manual

2. Editing two timbres

In each program, you can use two timbres: TIMBRE A and TIMBRE B.

TIP:

You can’t select TIMBRE B if the PROGRAM “p03: Common”

page Voice Mode parameter is set to “Single.” If “Layer” or

“Split” is selected, the TIMBRE A/B select buons will light to

indicate the timbre that you’re editing.

TIP:

The voice mode parameter in the PROGRAM “p03: Common”

page is common to the entire program.

Using two timbres (Layer)

When using two timbres, you have a choice of two modes that

determine how the timbres will work. In this example, we’ll set the

PROGRAM “p03: Common” page Voice Mode parameter to “Layer.”

When you set this parameter to “Layer,” the two timbres will be

heard simultaneously when you play the keyboard.

1. Use the PAGE +/- buttons to access the PROGRAM “p03

Common” page.

2. Turn the value dial to set the voice mode to “Layer.”

The TIMBRE A select button and the master effect timbre LEDs

will light up.

Selecting a timbre to edit

When editing a program that uses two timbres, you’ll need to select

a timbre to edit.

Use the TIMBRE A/B select buttons to select the timbre that you

want to edit. The timbre select button you selected will light up,

allowing you to edit that timbre.

Editing the filter and EG

On the KingKORG you can use the front panel knobs and buttons to

control the filter and EG in real time.

You can choose one of three ways in which the knobs will work

when you turn them. (PG: “5. GLOBAL parameters”)

FILTER

Cutoff (CUTOFF)

This adjusts the cutoff frequency of the filter. The brightness of

the sound will change. Turning the knob toward the left will

darken the sound; turning it toward the right will brighten the

sound.

Resonance (RESONANCE)

This adjusts the amount of resonance for the filter. Resonance

adds a distinctive tonal character.

EG (Envelope Generator)

Attack (ATTACK1, ATTACK2)

This adjusts the attack time of EG1 (filter EG) and EG2 (amp

EG). The attack specifies the time from note‐on (the moment you

press the key) until the attack level is reached. It changes the

way in which the EG1 and EG2 will start. Turning the knob

toward the left will shorten the attack time; turning it toward the

right will lengthen the attack time.

Decay (DECAY1, DECAY2)

This adjusts the decay time of EG1 (filter EG) and EG2 (amp EG). The

decay specifies the time from when the attack level is reached until the

sustain level is reached. Turning the knob toward the left will shorten

the decay time; turning it toward the right will lengthen the decay time.

Sustain (SUSTAIN1, SUSTAIN2)

This adjusts the sustain level of EG1 (filter EG) and EG2 (amp

EG). The sustain specifies the level that is reached after the decay

time has elapsed and is sustained as long as you hold down the

key. Turning the knob toward the left will lower the sustain level;

turning it toward the right will raise the sustain level.

Release (RELEASE1, RELEASE2)

This adjusts the release time of EG1 (filter EG) and EG2 (amp

EG). The release specifies the time from note‐off (the moment

you release the key) until the sound has decayed to silence. It

will vary the release time of EG1 and EG2. Turning the knob

toward the left will shorten the release time; turning it toward

the right will lengthen the release time.

Attack Level

Time

Note on

Note off

Level

1: Attack Time 3: Sustain Level

2: Decay Time 4: Release Time

EG2

Adjusting effect settings

The KingKORG provides master effects that let you apply a variety

of effects to the sound, such as distorting it, modulating it, or adding

reverberation. The master effects are applied to the overall sound of

the two timbres.

The master effects consist of three sections (PRE FX, MOD FX, REV/

DELAY), and you can choose one type of effect for each section.

For example you might choose “EP.AMP” for the PRE FX section,

“TREMOLO” for the MOD FX section, and “HALL” for the REV/

DELAY section. For each section, you can also specify the timbre(s)

where that effect will apply.

1. Press an FX type select dial to select the timbre(s) where that

effect will apply.

The selected timbre LED(s) will light up. If both timbre LEDs A

and B are unlit, that effect will not be applied.

The timbre LED B will not light if the program’s voice

mode is “Single.”

2. Select an effect.

The LED of the selected effect will light.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Korg KingKorg Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info