683161
178
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Calibration of Internal Reference Frequency
The internal reference frequency of this transceiver is preadjusted
at the factory. However, if calibration of the internal reference
frequency is necessary due to changes over time or other reasons,
this can be done by receiving WWVH (Hawaii), WWV (Colorado),
BPM (Xi’an) or other types of standard radio wave.
First of all, follow the steps below to set this transceiver to the mode
for receiving the standard radio wave signals. The following is an
example of the calibration procedure when the pitch frequency is
700 Hz.
1 Press [CW/ CW-R] to select CW mode.
2 Press [RIT] to turn off the RIT function.
3 Press [VOX] to turn off break-in.
If semi break-in is turned on, press [VOX] to turn it off.
If full break-in is turned on, turn the [DELAY] control to select
a value other than full break-in.
4 Turn the [AF] control to move to the 12 o’clock
position.
5 Turn the [MIC/PITCH] control to adjust the pitch to
a level for easy listening.
Turn the [MIC/PITCH] control until the pitch frequency reading
shows “700”.
6 Turn the [LO/WIDTH] and [HI/SHIFT] controls.
Turn the [HI/SHIFT] control until the shift frequency (SHIFT)
becomes “0”, followed by turning the [LO/WIDTH] control to
adjust the bandwidth (WIDTH) to “1000”.
For details on the REF I/O connector settings, please
refer to “Switching the Reference Signal” (16-8).
Calibration Procedure
Once the preparation is complete, follow the steps below to
configure the internal reference frequency of this transceiver.
1 Receive the standard radio wave signals.
To receive 10 MHz standard radio wave signals, turn the
Tuning control to adjust the value to exactly “10.000.00”.
A 700 Hz beat is heard.
.
f
AF
= f
reference
+ 700
[Hz]
x
f
display [MHz]
19.2
[MHz]
f
reference
Reference Frequency Shift
Adjust such that the received beat is audible on the CW pitch
frequency.
2 Press [MENU].
3 Press F [ADV.] to display the Advanced Menu
screen.
If F [ADV.] is not displayed, press F [MORE] to display F
[ADV.].
4
Select Advanced Menu [5] Reference Oscillator
Calibration.
5 Press F4 [SELECT].
.
6 Press F7 [CAL.T].
A 700 Hz calibration sidetone is generated. This sidetone
overlaps with the RX audio and a double beat is formed by the
difference in frequency.
If the double beat is not clearly audible, turn the [AF] control to
adjust the RX audio.
.
fsidetone = 700[Hz] 8[ppm]
+
(700 0.006
[Hz])
+
7 Press the F4 [–]/ F5 [+] or turn the [MULTI/CH]
control.
Perform adjustment until the cycle of the double beat
between the RX beat and sidetone reaches the maximum
and the double beat is no longer audible. At this point, the
difference in frequency between the RX audio and sidetone
is at the minimum level.
To restore the default setting, press and hold F2 [(RESET)].
8 Release F7 [CAL.T].
9 Press [ESC] to end the process.
If the signal used for calibration falls outside the range of
the reference signal input from an external source
(-10 dBm to +10 dBm) or frequency accuracy (10 MHz
±10 ppm), the internal reference frequency may not be
calibrated correctly.
17 MAINTENANCE AND ADJUSTMENT
17-2
178

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info