683161
99
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Switching the Scope Display Mode
1
Display the bandscope screen.
2
Press F2 [S.MODE].
If F2 [S.MODE] is not displayed, press F1 [MORE] to display
F2 [S.MODE].
Pressing F2 [S.MODE] each time switches the selection to
“Auto Scroll Mode”, “Fixed Mode” and “Center Mode” in
sequence.
Auto Scroll Mode (AUTO SCROLL MODE)
Moves the marker of the tuning frequency to within the scope
range. If the lower or upper limit of the display range is
exceeded, the scope range is automatically scrolled by half a
screen.
Fixed Mode (FIXED MODE)
Moves the marker of the tuning frequency to within the scope
range preconfigured for each amateur band. Up to 3 scope
ranges can be preconfigured for one amateur band.
Center Mode (CENTER MODE)
The marker of the tuning frequency is normally fixed at the
center.
Auto Scroll Mode
.
Fixed Mode
.
Center Mode
.
Switching the Display Frequency Span
When the bandscope is displayed in the Auto Scroll mode or
Center mode, the display frequency span (the width between the
lower and upper frequency limits in the bandscope screen) can be
adjusted.
Press F3 [SPAN].
If F3 [SPAN] is not displayed, press F [MORE] to display F3
[SPAN].
Pressing F3[SPAN] each time switches the frequency span.
Setting Value
5kHz/ 10kHz/ 20kHz/ 30kHz/ 50kHz/ 100kHz/
200kHz/ 500kHz
The display frequency span can be configured separately for
audio mode (SSB/AM/FM (including DATA mode)) and non-
audio mode (CW/FSK/PSK).
The default settings of the audio mode and non-audio mode
are “50Hz (± 25Hz)” and “10kHz (± 5Hz)” respectively.
Pressing and holding F3[SPAN] each time switches the
options in the reverse sequence.
The selected display frequency span is displayed in the
toolbar of the bandscope screen as “SPAN 50kHz”, for
example.
Marker Shift
This function shifts the scope range in the auto scroll mode
operation so that the marker is displayed at an easy to observe
position.
Shifting the Marker
Press F4 [SHIFT].
If F4 [SHIFT] is not displayed, press F [MORE] to display
F4 [SHIFT].
The marker shifts close to the preset shift position (default value
is center).
Depending on the relationship between the RX
frequency and the span, deviation of 1 grid to the left or
right may occurred in the shift operation.
Changing the Shift Position of Marker Shift
1
Press and hold F4 [SHIFT].
If F4 [SHIFT] is not displayed, press F [MORE] to display
F4 [SHIFT].
The transceiver enters the shift position configuration mode.
The value indicating the position of the selected vertical grid
line is displayed.
2
Move the shift position to the desired position using
the [MULTI/CH] control.
Pressing and holding F4 [SHIFT] moves the shift position to
the center.
3
Press F4 [SHIFT].
The transceiver exits the shift position configuration mode.
When observing the condition of the frequency calling
the DX station or the condition in the RX passband during
digital communication such as FT8, change the shift
position of the marker to display the RX frequency
marker at the edge. Doing so widens the width for
displaying the signal compared to when the marker is
near the center.
SCOPE FUNCTIONS 7
7-3
99

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info