683161
67
Verklein
Vergroot
Pagina terug
1/196
Pagina verder
Eight code abbreviations are supported, namely BT, AR, AS,
HH, SK, KN, BK and SN.
The code abbreviation received is displayed in 2 alphabets. For
example, when “AR” (code with no space between “A” and “R”)
is received, “AR” is displayed.
The codes might not be decoded correctly depending on the
signal quality.
If the keying speed of the target signal changes halfway, the
characters immediately before or after the change cannot be
decoded correctly.
Characters that cannot be decoded are indicated using an
underscore (_).
Time stamp and frequency information can be added to the TX/
RX details display area. (5-28)
This transceiver does not support Japanese characters.
Press [Page Up] / [Page Down] on the USB keyboard to scroll
through the information displayed in the TX/RX details display
area.
Noise Reduction 1, Noise Reduction 2, audio peak filter and RX
DSP equalizer do not function during CW decoding.
Adjusting the Decode Threshold Level
The threshold value for the signal strength to activate decoding
can be adjusted as follows. Raising the threshold level may reduce
erroneous detection due to noise.
1 Press F6 [THLD] in the CW communication screen
to switch to the threshold level configuration mode.
If F6 [THLD] is not displayed in the key guide, press F1
[MORE] to toggle the key guide display.
.
2 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control
to select a threshold level.
Setting Value 1 to 10 (default) to 30 (1-step)
Adjust the threshold value in the ascending order according
to the receiving status of noise, for example. Start from a
small value between the range of 1 to 30 and configure the
threshold value to a point where reception is good.
Pressing and holding F2 [(RESET)] resets the threshold
level to the default setting.
3
Press F1 [ ] to end the process.
Decode Filter
A decode filter (narrow-band filter used exclusively for decoding)
can be used when there is significant interference or noise while
decoding the Morse code.
Press F5 [DEC.FIL] in the CW communication
screen.
If F5 [DEC.FIL] is not displayed in the key guide, press F1
[MORE] to toggle the key guide display.
Pressing F5 [DEC.FIL] each time switches the decode filter
mode (Off/Normal/ Narrow).
The selected mode is displayed for about 2 seconds.
Transmitting Character Strings via USB Keyboard
Operation
Text input by the USB keyboard can be transmitted in Morse code.
1 Connect the USB keyboard (commercially
available) to this transceiver.
2 Press F4 [QUICK].
If F4 [QUICK] is not displayed in the key guide, press F1
[MORE] to toggle the key guide display.
Press F4 [QUICK] each time toggles the quick mode between
ON and OFF.
<< >> appears when the quick mode is ON.
3 Enter a character string using the USB keyboard.
When Quick Mode is ON:
The characters entered using the USB keyboard appear in the
character string buffer and encoding starts immediately.
When Quick Mode is OFF:
The characters entered using the USB keyboard appear in the
character string buffer. To start encoding, press [Enter] on the
USB keyboard or the F4 [START] key.
Sending a character string using the USB keyboard while the
update of TX/RX details display is paused cancels the paused
state.
The maximum number of characters that can be entered in the
character string buffer is 4300 characters.
To send a consecutive code (code abbreviation), input the
characters after inputting “~” (tilde). The characters are
encoded as a consecutive code until a space is inserted.
For example, when “~ HH” and “~ OSO” are input, they become
the code abbreviations for correction code and emergency
communication respectively.
To start encoding from a consecutive code while quick mode is
ON, input the first character of the consecutive code within the
time interval equivalent to 7 dots (space between words) after
inputting “~” (tilde).
COMMUNICATING AIDS 5
5-11
67

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TS-890S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TS-890S in de taal/talen: Engels als bijlage per email.

De handleiding is 21,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TS-890S

Kenwood TS-890S Gebruiksaanwijzing - Nederlands - 196 pagina's

Kenwood TS-890S Gebruiksaanwijzing - Deutsch - 196 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info