606707
59
Verklein
Vergroot
Pagina terug
1/77
Pagina verder
APRS-14
TX Interval Time <TX INTERVAL>
You can change the interval for automatically transmitting
APRS packets. Access <TX INTERVAL > and select 0.2, 0.5,
1, 2, 3, 5, 10, 20, 30 or 60 minutes. The default is 3 minutes.
Note:
With “AUTO” in < METHOD > and Beacon ON, pressing the Tuning
control to complete the setting causes the APRS packet to be immediately
transmitted. After that, APRS packets are transmitted at intervals of the
selected period.
While signals are present, an APRS packet is not transmitted after the
interval. after signals drop, transmitting is executed.
Decay Algorithm <DECAY ALGORITHM>
This function continuously extends the packet transmission
interval in the case that there is no change of position
information.
When the position data does not change, the data is transmitted
based on a Decay Algorithm (1 minute, 2 minutes, 4 minutes, 8
minutes, 16 minutes, 32 minutes, 32 minutes, 32 minutes, etc.)
When My station position data changes, the data is transmitted
using an interval time based on the set Initial Interval.
When the set time elapses and transmission is performed but a
busy signal is present, the transceiver does not transmit. When
there is no longer a busy signal, the transceiver attempts to
transmit.
Note:
While transmitting by pressing the [PTT] switch, beacon transmission is
reserved.
If My callsign is not set, the APRS packet will not be transmitted.
Independent of this interval, the transmission of the message is in 1 minute
intervals.
Proportional Pathing <PROPORTIONAL PATHING>
This function automatically changes the transmit packet path with
the elapsed time.
Operation example for when PROPORTIONAL PATHING = ON
Transmission interval is 2 minutes. (When the <DECAY
ALGORITHM> = ON, the decay transmission interval takes
precedence.)
The packet path changes with each transmission as shown
below (when the packet path is set as WIDE1-1, WIDE2-1).
2 minutes : DIRECT
4 minutes : WIDE1-1 (1 Hop)
6 minutes : DIRECT
8 minutes : WIDE1-1, WIDE2-1 (2 Hops)
10 minutes : DIRECT
12 minutes : WIDE1-1 (1 Hop)
14 minutes : DIRECT
16 minutes : WIDE1-1, WIDE2-1 (2 Hops)
This is repeated.
When jointly using a Decay Algorithm, if the speed is 1 knots or
slower, a Decay Algorithm pattern is used for transmitting, but if the
speed is 3 knots or faster, it changes to Proportional Pathing.
PROGRAMMING A PACKET PATH
Enter Menu mode and access Menu 612.
Select the packet path type from [New-N PARADIGM], [RELAY
PARADIGM], [STATE/SECTION/REGION], or [OTHERS].
When you press [USE], the
indicator appears on the left side
of the packet path type, showing the current used information.
[New-N PARADIGM]:
This digipeat type has been used mainly in North America, but is
now used worldwide.
1 Set the TYPE to [New-N PARADIGM], then press [USE].
2 Set WIDE 1-1 to [OFF] or [ON].
Set WIDE 1-1 to [ON] to use the digipeater of the RELAY type
(Fill-in type) with the New-N PARADIGM.
When set to [ON], 1 packet path in addition to WIDE 1-1 can be
used, as per the TOTAL HOPS setting.
3 Select the relay step number for the TOTAL HOPS setting.
You can confi rm the setting contents in PATH IS VIA.
[RELAY PARADIGM]:
This is one of the digipeat types used in Europe.
1 Set the TYPE to [RELAY PARADIGM], then press [USE].
2 Set RELAY to [OFF] or [ON].
Set RELAY to [ON] to use the digipeater of the RELAY type (Fill-
in type) with the RELAY PARADIGM.
When set to [ON], 1 packet path in addition to RELAY can be
used, as per the TOTAL HOPS setting.
3 Select the relay step number for the TOTAL HOPS setting.
You can confi rm the setting contents in PATH IS VIA.
59

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kenwood TM-D710GA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kenwood TM-D710GA in de taal/talen: Engels als bijlage per email.

De handleiding is 7,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Kenwood TM-D710GA

Kenwood TM-D710GA Gebruiksaanwijzing - Nederlands - 75 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Nederlands - 55 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Deutsch - 74 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - English - 55 pagina's

Kenwood TM-D710GA Gebruiksaanwijzing - Français - 77 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info