686369
16
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
16
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
3.13 I/O device
I/O device in the A7 MIG Welder system
Fieldbus
I/O
1
2
3
4
5
Figure 3.17 Connecting I/O device into A7 MIG Welder system
1. Fieldbus
2. Web user interface
3. Control cable for I/O device
4. I/O device 4/4 with connections
5. I/O extension card 8/8 with connections
The A7 I/O Device 4/4 is an optional digital control device with 4 inputs and 4 outputs.
It can be extended by the A7 I/O Extension card 8/8 that has additional 4 inputs and 4
outputs, resulting in the total of 8 inputs and 8. The I/O device is congured by using the
web user interface and controlled by the digital robot interface.
3.13.1 Installation
Follow these steps to install the I/O device. See the following gures for details.
Measure and drill holes for the I/O device to the mounting platform
Open the aluminum case by losing the four screws in the corners of the cover
Fasten the I/O device to the mounting platform by using appropriate screws
Remove plastic bungs from the I/O control cable holes
Screw strain reliefs to the holes
Thread I/O control cables through the strain reliefs and strip them (strip 8 mm o
from the wires of the cables)
Connect the wires of the I/O control cables to the inputs 1-4 and outputs 1-4
If you have an extension card, do these additional steps
Plug the at band cable of the extension card in to the matching connector of
the main card
Fasten the extension card on top of the elevation screws
Connect the wires of the I/O control cables to the inputs 5-8 and outputs 5-8
Fasten the strain reliefs (ensure, that I/O control cables and wires are not pulled
tight inside the I/O device)
Plug in and fasten the control cable – one end to the I/O device and the other
end to a matching connector in the welding power source
Power up the system
Congure inputs and outputs by using the web user interface
Test inputs and outputs by means of a robot teach pendant
Close and fasten the aluminum case
Do not plug in the extension card when the main card has been powered up. This may
cause damage on both cards.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A7 MIG Welder 350 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A7 MIG Welder 350 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info