686369
14
Verklein
Vergroot
Pagina terug
1/66
Pagina verder
14
A7 MIG Welder© Kemppi Oy 2018 1804
INTEGRATION GUIDE
3.10 Ethernet (web user interface server)
The welder system is equipped with a web user interface.
The server for the web user interface is in the robot
interface unit, and the connector for the server is at the
rear of the unit.
Connect the web user interface server to a laptop
computer, to another PC, or to a local area network by
using a CAT-5 or CAT-6 shielded Ethernet RJ-45 cable.
The communication speed of the network is 100 Mbps
(100Base-TX) and the maximum length of the cable is 90
m. Both crossover and direct cables are suitable.
The network conguration is described in Chapter 4,
Accessing the web user interface”.
3.11 Emergency input functions
There are two emergency input functions in the system,
for the emergency stop and gate door switch.
The emergency stop function halts the system
when the operator presses an emergency stop
button. After an emergency stop, the system
must be recovered manually.
The gate door switch halts the system when a
protective gate door is opened. Shielding gas
testing, the torch clean-up function (compressed-
air valve), wire inch, wire retraction, and the touch
sensor can be used in this situation. The touch
sensor voltage is automatically lowered to a
safety level (max. 110 V). After a gate door switch
action, the system is recovered automatically.
Both inputs have a separate three-pin connector at the
rear of the robot interface unit. The connectors have
identical pinout (see Figure 3.14, “Emergency input
connector pinout”). The inputs are galvanically isolated
from each other and from the other hardware I/O of the
robot interface unit. The inputs have individual short-
circuit-protected +24 V DC power supplies, each providing
up to 100 mA of continuous current.
Figure 3.14: Emergency input connector pinout
A
B C
A. Supply out +24 V, 100 mA
B. Emergency input signal
C. Supply GND
There are four alternative ways of connecting the
emergency stop and gate door switches (see Figure 3.15,
“Connecting the emergency stop switches”). Select one of
these ways on the basis of your emergency stop circuitry
and the switch types used. Connect the emergency stop
circuitry to the emergency input connector by using
custom cables.
The emergency inputs are congured via software. The
conguration is described in Subsection 5.1.7, “Emergency
stop settings.
Opening-action switch on 0
V line (default)
A
B
C
Opening-action switch on
+24 V line
A
B
C
Closing-action switch on 0
V line
A
B
C
Closing-action switch on
+24 V line
A
B
C
Figure 3.15: Connecting the emergency stop switches
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A7 MIG Welder 350 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A7 MIG Welder 350 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info