686377
9
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
9
A3 MIG Welder© Kemppi Oy 2018 1826
INTEGRATION GUIDE
4. SYSTEM CONFIGURATION
This section describes the settings that are typically
made once or that are otherwise necessary for integration
to be completed successfully. It does not describe those
settings that aect welding quality and are modied based
on the welding operation. For more information on the
operation-based settings, see the A3 MIG Welder Operating
manual.
Use the control panel and the DIP switches to perform
the system conguration within the integration.
4.1 Configure sensors and devices
Touch sensor output voltage
Use the DIP switches to set the touch sensing voltage
between +50…+200 V. Change the value during operation
depending on the work piece surface properties, if needed.
P2 switches 1-2 Voltage
ON
1 2 3 4 5 6 7 8
50 V
(default)
ON
1 2 3 4 5 6 7 8
80 V
ON
1 2 3 4 5 6 7 8
110 V
ON
1 2 3 4 5 6 7 8
200 V
Safety stop on/o
Use the DIP switches to set the emergency stop input on
and o. If you have installed an emergency stop switch
circuit for the system, set the emergency input to be on
accordingly. Otherwise, ensure that these parameters are
set to o to prevent possible false detection.
P2 switch 3 Safety stop
ON
1 2 3 4 5 6 7 8
Disabled (default)
ON
1 2 3 4 5 6 7 8
Enabled
Collision sensor on/o
Use the DIP switches to set the collision sensor on and o.
If you haven’t got a collision sensor installed in the system,
turn the sensor o to prevent possible false detections.
P2 switch 4 Collision sensor
ON
1 2 3 4 5 6 7 8
Disabled (default)
ON
1 2 3 4 5 6 7 8
Enabled
Collision sensor switch type
Use the DIP switches to select the switching type of
the collision sensor. The switch can be either opening
or closing. See Figure 3.4, Opening and closing action
switches”.
P2 switch 5 Switch type
ON
1 2 3 4 5 6 7 8
Opening (default)
ON
1 2 3 4 5 6 7 8
Closing
Byte order
Use the DIP switches to select the byte order according to
the robot type.
P2 switch 6 Byte order
ON
1 2 3 4 5 6 7 8
Little-endian (default)
ON
1 2 3 4 5 6 7 8
Big-endian
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Kemppi A3 MIG Welder bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Kemppi A3 MIG Welder in de taal/talen: Engels als bijlage per email.

De handleiding is 2,84 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info