804775
8
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
8 English
Note on checking the oil level.
Choke lever
Accelerator lever
Initial start-up
Fill with oil
1. Position the device on a level surface.
2. Unscrew the oil dipstick.
3. Fill with engine oil.
Note: The engine oil is not included in the scope of
delivery. The filling quantity and oil type are speci-
fied in the section "Technical data".
4. Wipe off the oil dipstick.
5. Insert the oil dipstick as far as it will go, but do not
screw in.
6. Pull out the oil dipstick. The oil level must lie in the
marked section of the oil dipstick.
7. Top up the engine oil if the level is too low.
8. Screw in and tighten the oil dipstick.
Initial startup
Check the oil level
1. Position the device on a level surface.
2. Unscrew the oil dipstick.
3. Wipe off the oil dipstick.
4. Insert the oil dipstick as far as it will go, but do not
screw in.
5. Pull out the oil dipstick. The oil level must lie in the
marked section of the oil dipstick.
6. Top up the engine oil if the level is too low.
7. Screw in and tighten the oil dipstick.
Refuelling
1. Unscrew the fuel tank cap.
2. Fill fuel up a maximum of the lower edge of the filling
nozzle.
3. Fit the fuel tank cap and screw tight.
Positioning the pump
The delivery performance of the pump is heavily de-
pendent on the operating conditions. Adhering to the
following rules will ensure optimum performance.
Keep the height difference between the water sur-
face and the pump as small as possible.
Position the pump so that the suction hose is a short
as possible.
A long pressure hose is better than a long suction
hose.
Do not unnecessarily long hoses.
Connecting the hoses
1. Push the hose clip onto the suction hose.
Illustration B
1Suction hose (not in scope of delivery)
2Hose clip
3Hose nipple
4Union nut
5Flat seal
2. Slide the union nut onto the hose nipple.
3. Push the suction hose onto the hose nipple.
4. Position and tighten the hose clip.
5. Fit a flat seal between the suction nozzle and hose
nipple.
Note: A reinforced hose suitable for vacuum appli-
cations must be used for the suction hose.
6. Connect the suction hose to the suction nozzle and
tighten the union nut.
7. Fit the suction filter to the other end of the suction
hose.
Illustration C
1Suction hose (not in scope of delivery)
2Hose clip
3Suction filter
8. Fit a hose nipple, union nut and hose clip to the
pressure hose (not included in the scope of deliv-
ery).
9. Fit a flat seal between the hose nipple and outlet.
10. Connect the pressure hose to the outlet and tighten
the union nut.
Operation
Venting the pump
ATTENTION
Risk of damage
The seals will be damaged if the pump runs dry.
Vent the pump before starting. If the pump is accidentally
run dry then stop the engine immediately and allow the
pump to cool down before starting the venting procedure.
1. Unscrew the cap from the filler opening.
2. Fill the pump completely with water.
3. Screw the cap back into the filler opening and tighten.
Starting the device
1. Vent air from the pump.
2. Open the fuel cock.
3. Push the choke lever to the left.
4. Push the accelerator lever to approximately 1/3 of
the total range.
5. Set the power switch to "I".
6. Pull the starter cord slowly until a strong resistance
is discernible then pull strongly.
7. Slowly return the starter cord.
ATTENTION
Risk of damage
A rapidly returning starter cord damages the device.
Slowly return the starter cord.
8. Push the choke lever to the right once the engine
has started.
9. Push the accelerator lever to the left until reaching
the desired speed. The flow rate of the pump de-
pends on the engine speed.
10. Check the function of the pump. Dry running damag-
es the pump. Switch off the engine and repeat vent-
ing of the pump if the pump does not deliver water.
Switching the device off in an emergency
1. Set the power switch to "0".
Switching off the device
1. Push the accelerator lever all the way to the right.
2. Set the power switch to "0".
3. Close the fuel cock.
Draining the water
1. Unscrew the water drain screw.
2. Allow the water to drain from the pump.
3. Unscrew the cap from the filler opening.
4. Flush the pump with fresh water.
5. Allow the fresh water to drain away.
6. Screw the cap into the filler opening and tighten.
7. Screw in and tighten the water drain screw.
Transport
Set the power switch to "0" before transport.
Allow the engine to cool down for at least
15 minutes before loading.
Keep the device horizontal during transport to pre-
vent fuel from spilling out.
When transporting in vehicles, secure the device
against rolling away, slipping and tipping according
to the respectively applicable guidelines.
Be aware of the weight of the device during trans-
port.
Storage
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
ATTENTION
Risk of damage
Do not place any heavy objects on the device.
Store the device in a dry and dust-free place.
Cleaning the device
The device must be cleaned before storage.
1. Allow the device to cool down for a half-hour if it was
recently in operation.
2. Flush the pump with clear water.
3. Manually wash the exterior of the device with a
small amount of water.
4. Rub all accessible surfaces dry.
5. Unscrew the water drain screw and allow the water
to drain out.
6. Screw in and tighten the water drain screw.
7. Lightly oil rust-prone surfaces.
8. Spray the control elements with silicone spray.
Storage duration of 1...2 months
1. Add petrol stabiliser to the fuel tank.
2. Top up the fuel tank.
Storage duration of 2...12 months
Additionally:
1. Close the fuel cock.
2. Place a container under the carburettor.
Illustration D
1Carburettor
2Drain screw
3. Unscrew the drain screw.
4. Collect the fuel in the container.
5. Screw in and tighten the drain screw.
6. Empty the settling cup (see "Care and Maintenance/
Cleaning the settling cup").
Storage duration longer than 12 months
Additionally:
1. Unscrew the spark plug.
2. 5...10 cm3 Add engine oil to the cylinder.
3. Slowly pull the starter cord several times to distrib-
ute the oil in the engine.
4. Screw in the spark plug.
5. Change the oil (see "Care and Maintenance/Chang-
ing the oil").
6. Pull the starter cord slowly until a strong resistance
is discernible.
Care and service
DANGER
Danger of injury from electric shock.
The device can start unintentionally. You can be injured
by moving parts.
Remove the spark plug connector before performing
any maintenance work.
CAUTION
Danger of burns.
Hot device components cause burns if touched.
Allow the device to cool down before working on it.
* See "Startup" for a description.
** See "Maintenance work" for a description.
Maintenance intervals
Each time before use
1. Check the device for correct condition and opera-
tional safety. Do not start up a damaged device.
2. Check the oil level. *
3. Check the air filter. **
Once after 1 month or 20 operating hours
1. Change the oil. **
Every 3 months or 50 operating hours
1. Clean the air filter. **
Perform cleaning more frequently in a dusty applica-
tion environment.
Every 6 months or 100 operating hours
1. Change the oil. **
2. Clean the settling cup. **
3. Check and clean the spark plug. **
4. Clean the spark catcher (not included in the scope
of delivery). **
Annually by the authorised Customer Service
department
1. Check and adjust the valve play.
2. Clean the fuel tank and fuel filter.
3. Replace the air filter insert.
4. Replace the spark plug.
5. Check/adjust the idling mixture speed.
6. Check/adjust the valve play.
7. Check the pump impeller.
8. Check the gap between the casing and impeller.
9. Check the pump inlet valve.
Every 2 years by the authorised Customer Service
department
1. Check the fuel line and replace if necessary.
2. Clean the engine combustion chamber.
Maintenance work
Check the air filter
1. Lift the strap and remove the cover.
Illustration E
1Cover
2Lap
3Air filter insert
2. Check the air filter insert for soiling. Clean the air fil-
ter if necessary or replace if damaged (see "Clean-
ing the air filter").
3. Fit the cover and latch into place.
Cleaning the air filter
ATTENTION
Risk of damage
Penetrating dust can destroy the engine if the air filter
insert is absent.
Do not operate the device without an air filter insert.
1. Open the air filter (see "Checking the air filter").
2. Remove the air filter insert.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Karcher WWP 45 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Karcher WWP 45 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 10.15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info