-2
ATTENTION
Risk of damage. Ensure that no liquid en-
ters the intake port of the suction turbine
under the waste water tank. Wipe up spilled
liquid.
Fill in fresh water (maximum 50 °C).
Observe the maximum filling level indi-
cator. Leave room for detergent.
Add detergent. Follow dosing instruc-
tions for detergent.
Recommended detergents:
Detergents are available in specialised
stores.
Close the cover of the fresh water res-
ervoir.
Release the star knob for the height ad-
justment of the steering wheel.
Adjust the steering wheel to the desired
height.
Tighten the star handle.
Push the appliance to the work station.
Unfold the parking support.
Adjust the twist grip to a brush contact
pressure suitable for the type of carpet
as follows:
Fold the parking support in.
Switch on the appliance on the carpet to
be cleaned.
If support is present while the brush
drive is being pushed forward, the ad-
justment is correct.
If no support is noticeable when you
push, increase the setting and repeat
the procedure.
If the indicator lamp for the brush drive
shows a malfunction after a few sec-
onds of operation, reduce the setting.
A pause in operation of 10 minutes must be
adhered to after the maximum operating
duration so the device can cool down.
During the pause in operation, the waste
water tank and the coarse dirt container
can be emptied, the brushes checked and
the fresh water tank topped up.
ATTENTION
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
Attach the extension cable to the cable
clips for strain relief.
First connect the extension cable to the
mains and then connect it to the mains
socket.
Turn the programme selector switch to
the desired function.
Switch on the detergent solution switch
if necessary.
Pull the safety switch towards the steer-
ing wheel, the brush drive and the appli-
cation of the cleaning solution are
switched on (if preset).
Push the appliance forward until the
parking stand folds up and the cleaning
head touches the ground.
Move the appliance over the surface to
be cleaned.
While working, keep an eye on the sight
glass for airflow. If water or foam is vis-
ible, switch off the appliance immedi-
ately. Empty the waste water tank or
add defoamers to the waste water tank.
Note:
If the brush rotation direction switch on the
steering wheel is actuated, the appliance
also moves backwards.
Use the right side for cleaning close to the
edge.
If the brush drive indicator light is flashing
red after a short operating period, reduce
the brush contact pressure.
Figure 4, see cover page
1 Suction hose
2 Vacuum bar
3 Detergent solution coupling
Turn the steering wheel to reverse
movement.
Pull out the suction hose from the vacu-
um bar.
Connect the suction hose of the appli-
ance to the suction hose of the addition-
al tool.
Connect the hose for the detergent so-
lution of the additional tool to the cou-
pling on the cleaning head.
Turn the programme selection switch to
the additional tool position.
Switch on "Detergent" button.
Perform cleaning with the additional tool.
Release the safety switch.
Drive the appliance forward for another
1-2 m to draw off residual water.
Set the programme selector switch to
"OFF".
ATTENTION
The brush can be permanently deformed.
Always set the appliance down with the
parking support folded out.
Unfold the parking support.
몇WARNING
Please observe the local provisions regard-
ing the wastewater treatment.
Set the programme selector switch to
"OFF".
Fold the parking support in.
Remove the cover of the waste water tank.
Take the waste water drain hose out of
the support and lower it over a suitable
collecting device.
Crush or bend the dosing equipment.
Open the lid of the dosing equipment.
Let off dirt water by opening the dosage
device at the discharge hose.
The wastewater flow can be controlled
by squeezing the dosing unit.
Rinse the dirt water reservoir with clear
water.
Note:
The waste water tank can also be removed
and carried separately to the disposal facil-
ity.
몇WARNING
Please observe the local provisions regard-
ing the wastewater treatment.
Push down the coupling to drain the
fresh water.
Pull off the hose and swivel it down.
In case of danger of frost:
Empty the fresh and dirt water reser-
voirs.
Store the appliance in a frost-protected
room.
Application Detergent
Intermediate cleaning RM 768 iCapsol
Basic cleaning RM 764 liquid
Settings
Adjusting the brush contact pressure
Needle felt
2 (3)
Textured cut, Level loop pile
3 (4)
Cut pile, Cut and loop pile
1...2*
Plush pile, Velour
1...2*
Frieze, Twist Cut Pile
1...2*
( ) at low propulsion
* depending on the fibre height
Maximum operating duration
Carpet Operating duration,
minutes
Intermedi-
ate clean-
ing
Basic
cleaning
Needle felt 50...60 8...10
Textured cut, Level
loop pile
40...50 8...10
Cut pile, Cut and
loop pile
40...50 6...8
Plush pile, Velour 25...30 Spot
cleaning
mode
Frieze, Twist Cut Pile 25...30 Spot
cleaning
mode
Cleaning
Additional tool (option)
Shutting Down the Appliance
Emptying the waste Water tank
Emptying the Fresh Water Tank
Frost protection
