636490
62
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
DHW heating
6 720 645 817 (2010/09)
62
Cylinder connection on the heating side
The sizing of the connection lines for the cylinder flow
and return is based on a temperature differential of 20 K.
Table 35 shows the resulting internal diameters. When
using flexible connection lines, such as corrugated
stainless steel hoses, apply a higher pressure drop than
for rigid pipework.
To prevent unnecessary pressure drop and cylinder
cool-down through pipe circulation, keep primary lines
as short and well insulated as possible.
Generally the cylinder return is connected near the cold
water inlet. This means that the DHW cylinder operates
in countercurrent mode. As a result, the heat input is
optimally transferred.
If required, provide a heating time control (Æ heating
controls).
Provide an effective means of venting (e.g. air separator)
at the highest point between the cylinder and the boiler
to prevent operating faults through air locks.
The DHW cylinder can cool down in summer mode
through gravity circulation. To prevent this, install a
non-return valve or check valve in the cylinder return.
Mixed installation
According to DIN 1988, the installation of a nonferrous
heavy metal fitting is adequate to protect materials with
different potentials, such as stainless steel and
zinc-plated steel, against electrochemical corrosion. In
such cases (this also includes DHW cylinders made from
enamelled steel) adaptor fittings made from red bronze
have often been used.
However, the most recent experiences with DHW with
high conductivity and a high level of hardness (> 15 °dH)
have shown that there is still a risk of corrosion forming
at the adaptor point, even when red bronze fittings are
used. Furthermore, in these areas incrustations were
discovered that in some cases result in a complete
closure of the pipe cross-section. For such mixed
installations in accessible areas, we therefore
recommend the use of insulation fittings as a suitable
solution.
Cylinder
Recommended internal
diameter of the connection lines
SK 300-3 ZB DN 25
SK 400-3 ZB DN 32
SK 500-3 ZB DN 32
SK 800-ZB DN 65
SK 1000-ZB DN 65
SE 300-1 DN 25
Tab. 35
The following section only applies to
enamelled DHW cylinders, not stainless
steel cylinders SE 300-1.
62

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Junkers MKB 560-3 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Junkers MKB 560-3 A in de taal/talen: Engels als bijlage per email.

De handleiding is 15,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info