636490
61
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
DHW heating
6 720 645 817 (2010/09)
61
DHW convenience
The performance factor to DIN 4108 corresponds to the
number of residential units to be supplied, each with
3.5 occupants, one standard bath tub and two further
draw-off points. Larger bath tubs may require a higher
N
L
factor; fewer occupants may require a lower one.
DHW priority circuit
A DHW priority or partial priority circuit can be selected
at the Fx controllers.
With a partial DHW priority circuit, it is advisable that the
heating circuits are designed as mixed heating circuits.
This way, low flow temperatures can still be achieved in
the heating circuits, even if there are high flow
temperatures during cylinder heating.
Cylinder temperature sensor
All DHW cylinders are equipped with an encoded NTC
cylinder sensor that is connected to the IPM 1 or IPM 2
load switching module. The cylinder temperature sensor
enables easy adjustment of the DHW temperature at the
controller for the indirectly heated cylinder.
Valves/taps
All commercially available mono lever taps and
thermostatic mixer valves can be used with Junkers
DHW cylinders. In the event of frequent successive
short-term drawing events, the set cylinder temperature
may overshoot and a hot layer may form in the upper
section of the cylinder. This temperature overshoot can
be reduced by connecting a DHW circulation line with a
timer-controlled DHW circulation pump. When making
the cold and hot water connections at the cylinder,
observe DIN 1988 and the regulations of the local water
board. For Junkers DHW cylinders up to 200 l capacity,
cold water safety assemblies are available from the
Junkers range of accessories. Provide the cold water
safety assembly on site for larger DHW cylinders.
When selecting the operating pressure for valves/taps,
ensure that the maximum permissible pressure
upstream of these valves/taps is restricted to 5 bar, in
accordance with DIN 4109 (noise protection in
buildings; source: Commentary DIN 1988, part 2,
page 156). For systems with a higher static pressure,
install a pressure reducer. The installation of a pressure
reducer is a simple but highly effective measure to
reduce excessive noise levels. For example, simply
reducing the flow pressure by 1 bar will result in a
reduction of the noise level by 2 to 3 dB(A)
(source: Commentary DIN 1988, part 2, page 156).
Connection on the water side of the cylinder
Make the cold water connection in accordance with
DIN 1988 using suitable individual fittings or a complete
safety assembly. The safety valve must be type-tested
and adjusted so that exceeding the permissible cylinder
operating pressure by more than 10 % is safely
prevented. If the static system pressure is lower than
80 % of the safety valve response pressure, install a
pressure reducer upstream of the safety valve.
To prevent water losses through the safety valve as far
as possible, we recommend the installation of an
expansion vessel that is suitable and approved for DHW
(Æ page 64).
The blow-off line must not be able to be closed and must
terminate freely and visibly in a drainage point. Sizing is
subject to the cylinder size:
For cylinders with 200 to 1000 l capacity, the following
standard values apply for sizing:
Size of the safety valve (inlet connection): DN 20
Connection thread (inlet): R ¾
Connection thread (outlet), blow-off line: R 1
Condensing
boiler
Cylinder heat input in kW
Min. Max.
KBR 120-3 A 28 113
KBR 160-3 A 38 150
KBR 200-3 A 56.2 187
KBR 240-3 A 67.6 225
KBR 280-3 A 79.2 263
MKB 240-3 A 28 226
MKB 320-3 A 38 300
MKB 400-3 A 56.2 374
MKB 480-3 A 67.6 450
MKB 560-3 A 79.2 526
Tab. 34 Cylinder heat input from condensing boilers in kW
CAUTION: Damage through overpressure
If using a non-return valve, the safety valve
must be installed between the non-return
valve and the cylinder connection (cold
water).
61

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Junkers MKB 560-3 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Junkers MKB 560-3 A in de taal/talen: Engels als bijlage per email.

De handleiding is 15,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info