636490
36
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
Engineering information and sizing the heat source
6 720 645 817 (2010/09)
36
5 Engineering information and sizing the heat source
5.1 Operating conditions
Tab. 18 provides an overview of the conditions that must be observed, subject to the application and the local
system-specific circumstances.
5.2 Water quality
As there is no pure water for the heat transfer, observe
the water quality. Unsuitable water quality can damage
heating systems due to scaling and corrosion.
Fill the system with clean mains water only that meets
the requirements below.
To protect the appliance from scale damage throughout
its service life and ensure trouble-free, economical
operation, the overall quantity of hardness constituents
in the fill and top-up water of the heating circuit must be
limited.
To check the permitted amounts of water subject to the
fill water quality, either perform the following
calculations or consult the graphs.
Checking the maximum amounts of fill water subject to
water quality
The fill and top-up water has to meet certain
requirements depending on the total boiler output and
the resulting water volume of a heating system.
Use the following formula to calculate the maximum
amount of water that may be introduced without
treatment:
Form. 1 Calculation of the maximum amount of water that
may be introduced without treatment
Ca(HCO
3
)
2
Concentration calcium hydrogen carbonatein mol/m
3
Q Boiler output in kW
V
max
Maximum fill and top-up water over the entire service
life of the boiler in m
3
Information about the calcium hydrogen carbonate
(Ca(HCO
3
)
2
) concentration of the mains water can be
obtained from your water supply utility. If these details
are not included in the water analysis, the concentration
of calcium hydrogen carbonate can be calculated as
follows from carbonate hardness and calcium hardness.
Example
Calculation of the maximum permissible amount of fill
and top-up water V
max
for a heating system with a total
boiler output of 560 kW. The analysis values for
carbonate hardness and calcium hardness are quoted in
the older unit °dH.
Carbonate hardness: 15.7 °dH
Calcium hardness: 11.9 °dH
The following results from the carbonate hardness:
Ca(HCO
3
)
2
=15.dH×0.179 = 2.8mol/m
3
The following results from the calcium hardness:
Ca(HCO
3
)
2
=11.dH×0.179 = 2.13mol/m
3
The lower of the two values calculated from calcium and
carbonate hardness is decisive for calculating the
maximum permissible water volume V
max
.
Form. 2
Δϑ
max
Minimum
boiler water
flow rate
Max. water
flow rate
Minimum
boiler water
temperature
Operating
interruption
Heating circuit
control unit with
heating mixer
Minimum return
temperature
Full load = 30 K
Partial load = 40 K
No requirements
Results from
ΔT=8K
No requirements
To transfer the
max. output
ΔT must be < 30 K
Tab. 18 Suprapur operating conditions
V
max
0.0235
Q
Ca HCO
3
()
2
--------------------------------
×=
.
V
max
0.0235
560 kW
2.13 mol/m
3
------------------------------- -
× 6.2 m
3
==
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Junkers MKB 560-3 A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Junkers MKB 560-3 A in de taal/talen: Engels als bijlage per email.

De handleiding is 15,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info