Handleiding Janome Memory Craft 5200 (pagina 75 van 81) (Engels)

602029

Verklein

Vergroot

Pagina terug

1/81

Pagina verder

INSTRUCTION BOOK

IMPORTANT SAFETY INSTRUCTIONS

This sewing machine is not a toy. Do not allow children to play with this machine.

The machine is not intended for use by children or mentally infirm persons without proper supervision.

This sewing machine is designed and manufactured for household use only.

Read all instructions before using this sewing machine.

DANGER— To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the

electric outlet immediately after using and before cleaning.

2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 12 Volts 5 Watts.

WARNING— To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow children to play with the machine. The machine is not intended for use by children or

infirmed persons without proper supervision.

Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by

or near children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealer or service center for examination,

repair, electrical or mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing

machine and foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep fingers away from all moving parts. Special care is required around the sewing machine

needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as

threading the needle, changing the needle, threading the bobbin or changing the presser foot, and

the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or

when making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

Please note that on disposal, this product must be safely recycled in accordance with relevant National

legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance.

(European Union only)

The design and specifications are subject to change without a prior notice.

TABLE OF CONTENTS

NAME OF PARTS

Name of Parts .................................................................... 2

Standard Accessories ........................................................ 3

Extension Table .................................................................. 4

Stitch Chart ........................................................................ 4

GETTING READY TO SEW

Connecting the Power Supply ............................................ 5

Controlling Sewing Speed .................................................. 6

Speed control slider ........................................................... 6

Foot control ........................................................................ 6

Function Buttons ........................................................... 7-11

Mode selection ................................................................... 9

Pattern selection .............................................................. 10

Help button ....................................................................... 11

Customizing Machine Settings .................................... 12-14

Resumption setting .......................................................... 12

Sound setting ................................................................... 12

Language setting.............................................................. 13

Pop-up window duration time setting ............................... 13

Customizing the preset value for the stitch length

and width .......................................................................... 14

Restoring the original settings .......................................... 14

Presser Foot Lifter............................................................ 15

Changing the Presser Foot .............................................. 15

Removing and Attaching the Foot Holder ........................ 15

Variety of Presser Feet and Their Uses ........................... 16

Bobbin Winding ................................................................ 17

Removing the bobbin ....................................................... 17

Setting the spool of thread ............................................... 17

Extra spool pin ................................................................. 17

Bobbin winding ................................................................. 18

Inserting the bobbin.......................................................... 19

Threading the Machine .................................................... 20

Built-in needle threader .................................................... 21

Drawing Up Bobbin Thread .............................................. 22

Changing the Needle ....................................................... 23

Balancing Thread Tension ................................................ 24

Pressure Adjusting Lever ................................................. 25

Dropping and Raising the Feed Dog ................................ 25

BASIC AND UTILITY STITCHES

Straight Stitches .......................................................... 26-30

Sewing on heavy fabric .................................................... 26

Securing a seam .............................................................. 27

Using the seam guides on the needle plate ..................... 27

Turning a square corner ................................................... 27

Using the quilting guide .................................................... 27

Straight stitch in left needle position................................. 28

Adjusting the needle drop position ................................... 28

Adjusting the stitch length ................................................ 28

Variety of Straight Stitches .......................................... 29-30

Zipper Sewing ............................................................. 31-32

Basting ............................................................................. 33

Rolled Hem ...................................................................... 34

Zigzag Stitch .................................................................... 35

Changing the stitch width ................................................. 35

Changing the stitch length................................................ 35

Overcasting ...................................................................... 36

Tricot Stitch ...................................................................... 36

Overedge Stitch ............................................................... 36

Knit Stitch ......................................................................... 37

Double Overedge Stitch ................................................... 37

Overlock Stitch ................................................................. 37

Blind Hem......................................................................... 38

Button Sewing .................................................................. 39

Buttonholes ................................................................. 40-47

Variety of buttonholes ....................................................... 40

Square buttonhole ....................................................... 41-44

Adjusting buttonhole width ............................................... 44

Adjusting stitch density..................................................... 44

Corded buttonhole............................................................ 45

Round-end buttonhole...................................................... 46

Keyhole buttonhole .......................................................... 46

Knit buttonhole ................................................................. 47

Faux chain buttonhole ...................................................... 47

Eyelet ............................................................................... 48

Darning............................................................................. 49

Tacking ............................................................................. 51

QUILTING AND DECORATIVE STITCHES

Quilting ............................................................................. 52

Free motion quilting.......................................................... 52

Patchwork ........................................................................ 52

Pintucking......................................................................... 53

Applique ........................................................................... 53

Shell Tuck......................................................................... 54

Scallop ............................................................................. 54

Smocking ......................................................................... 54

Fagoting ........................................................................... 55

Cording............................................................................. 55

Satin Stitches ................................................................... 56

Twin Needle Sewing ......................................................... 57

PROGRAMMING PATTERNS AND LETTERS

Programming the Pattern Combination ............................ 58

Programming the mirror image patterns .......................... 59

Sewing a pattern combination from the beginning ........... 61

Sewing the current pattern from the beginning ................ 61

Programming French knots .............................................. 62

Extender Stitches ............................................................. 63

Programming Letters........................................................ 65

Selecting a letter style ...................................................... 65

Programming letters ......................................................... 66

Programming letters and decorative patterns .................. 67

Viewing a long text ........................................................... 67

Editing the Programmed Patterns ............................... 68-70

Deleting a letter (pattern) ................................................. 68

Inserting a letter (pattern) ................................................. 68

Duplicating a pattern (letter) ............................................. 68

Stitch adjustment of programmed patterns ...................... 69

Unified needle drop position............................................. 70

Storing and Recalling the Pattern Combination ............... 71

Storing the pattern combinations ..................................... 71

Overwriting a stored combination..................................... 71

Recalling a stored combination ........................................ 72

Deleting a stored combination.......................................... 72

Correcting Distorted Stitch Patterns ................................. 73

CARE AND MAINTENANCE

Cleaning the Hook Race and Feed Dog .......................... 74

Inserting the bobbin holder............................................... 74

Replacing the Light Bulb .................................................. 75

Warning Messages ..................................................... 76-77

Troubleshooting ............................................................... 78

NAME OF PARTS

Name of Parts

q Function buttons

w Liquid crystal display

e Screen sharpness adjustment dial

r Bobbin winder stopper

t Bobbin winder spindle

y Spool pin

u Large spool holder

i Thread guide

o Take-up lever

!0 Thread tension dial

!1 Face cover

!2 Thread cutter

!3 Needle threader

!4 Needle plate

!5 Extension table (Accessory box)

!6 Hook cover plate

!7 Hook cover release button

!8 Feed balancing dial

!9 Attachment hole

@0 Speed control slider

@1 Start/stop button

@2 Reverse stitch button

@3 Auto-lock button

@4 Up/down needle position button

@5 Presser foot holder

@6 Thumb screw

@7 Presser foot

@8 Needle

@9 Needle clamp screw

#0 Carrying handle

#1 Bobbin thread cutter

#2 Handwheel

#3 Power switch

#4 Machine sockets

#5 Drop feed dog lever

#6 Free-arm

Buttonhole lever

#8 Presser foot lifter

#9 Hole for additional spool pin

NOTE:

The design and specifications are subject

to change without a prior notice.

Standard Accessories

Zigzag foot A (set on the machine)

w Overedge foot C

e Rolled hem foot D

r Zipper foot E

t Satin stitch foot F

y Blind hem foot G

u Cording foot H

i Overcast foot M

o Automatic buttonhole foot R

!0 Darning foot P

!1 Button sewing foot T

!2 Bobbins

!3 Needle set

!4 Quilting bar

!5 Large spool holder (set on the machine)

!6 Small spool holder

!7 Extra spool pin

!8 Spool pin felt

!9 Spool stand

@0 Screwdriver

@1 Screwdriver

@2 Lint brush

@3 Seam ripper/Buttonhole opener

@4 Stitch chart

@5 Stitch chart holder

@6 Instruction book

@7 Power supply cable

@8 Foot control

NOTE:

Accessories can be stored in the extension

table (see page 4).

!7 !8

Extension Table

The extension table provides an extra surface for sewing bulky

materials, and can be removed for free-arm sewing.

Detaching the table

Pull the table away from the machine as illustrated.

Free-arm sewing can be used for:

Stitching sleeves, waistbands, pant legs or any tubular garment

area, darning socks as well as mending knees, elbows or children’s

wear.

Attaching the table

Push the extension table until it snaps into the machine.

q Pin

w Hole

Stitch Chart

Insert the pin into the hole for additional spool pin.

Insert the stitch chart into the slot of chart holder.

q Stitch chart

w Slot

e Chart holder

r Pin

t Hole for additional spool pin

Accessory storage

Open the lid toward you.

The accessories can be conveniently stored in the foot

compartment and space under it.

q Lid

w Foot compartment

To use start/stop button

Turn off the power switch.

Insert the machine plug into the machine.

Insert the power supply plug into the wall outlet.

Turn on the power switch.

GETTING READY TO SEW

Connecting the Power Supply

To use foot control

Turn off the power switch.

Pull out the foot control cable gently.

Insert the foot control plug into the machine.

Insert the machine plug into the machine.

Insert the power supply plug into the wall outlet.

Turn on the power switch.

q Power switch

w Foot control plug cord

e Machine socket for foot control

r Machine plug

t Machine socket for power supply

y Power supply plug

u Wall outlet

CAUTION

Always turn the power switch off and unplug the sewing machine

from the electrical outlet when the machine is not in use.

NOTE:

The start/stop button cannot be used when the foot control is

connected to the machine.

q Power switch

w Machine plug

e Machine socket for power supply

r Power supply plug

t Wall outlet

CAUTION

Do not pull the foot control cable beyond the red mark to avoid

damage to the foot control.

i Red mark

CAUTION

When turning off the machine after straight stitch sewing, be sure

to open the needle plate hole to prevent the needle from hitting

the needle plate.

Press button to open the needle plate before turning the

machine off.

NOTE:

Do not turn the machine off while an hourglass is

indicated on the LCD screen.

Foot control

Controlling Sewing Speed

Speed control slider

Sewing speed can be varied according to your sewing needs with

the speed control slider.

q To increase sewing speed, slide it to the right.

w To decrease sewing speed, slide it to the left.

Sewing speed is varied by the foot control.

The harder you press down on the foot control, the faster the

machine runs.

The machine runs at the maximum speed set by the speed

control slider when the foot control is fully depressed.

Operating Instructions:

The symbol “O” on a switch indicates the "off" position of a

switch.

For appliances with a polarized plug (one blade wider than the

other): To reduce the risk of electric shock, this plug is intended

to fit in a polarized outlet only one way. If it does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install the proper outlet. Do not modify the plug in

any way (U.S.A.and Canada only).

* Foot control model 21371 is used with this sewing machine.

When stitches (mode 1) (mode 2)

are selected, the machine will immediately sew locking stitches

when the Auto-lock button is pressed, then automatically stop.

When sewing any other stitches, the machine will sew locking

stitches at the end of the current pattern and automatically stop.

w Reverse stitch button

When stitches (mode 1) (mode 2)

are selected, the machine will sew in reverse while the reverse

stitch button is pressed.

If you press the reverse stitch button when sewing any other

stitches, the machine will immediately sew locking stitches and

automatically stop.

r Up/down needle position button

Press this button to bring the needle up or down. The machine

will stop with the needle up or down depending on the needle

position determined by this button.

NOTE:

The needle will always stop in the up position after

sewing buttonholes, bartacks, eyelets and darning.

e Auto-lock button

Function Buttons

Press this button to start or stop the machine. The machine starts

running slowly for the first few stitches, it then runs at the speed

set by the speed control slider.

NOTE:

• Start/stop button cannot be used when the foot control is

connected to the machine.

• If you start the machine with the presser foot up, a warning

message will appear to advise you to lower the foot.

Lower the foot and rstart the machine again.

t Warning message

q Start/stop button

q Screen sharpness adjusting dial

Use this dial to adjust the brightness of the liquid crystal

display. If the screen is not clear, adjust the screen

brightness with this dial.

w Mode button

Press this button to change the mode.

Mode 1: Direct pattern selection

Mode 2, 3: Utility and decorative stitch pattern selection

e Letter style button

Press this button to select letter style for sewing letters.

r Stitch width adjusting button

Press “+” or “–” to change the stitch width.

t Stitch length adjusting button

Press “+” or “–” to change the stitch length.

y Edit button (see pages 12, 13, 67-69)

Press this button to enter the editing mode. In the editing

mode, this button is used to shift the cursor to the left.

u Help button (see pages 11-13. 67)

Press this button to view alternative applications of certain

stitches. In the editing mode, this button is used to shift the

cursor to the right.

i Twin needle button (see page 57)

Press this button for twin needle sewing.

o Memory/call button (see pages 14, 71, 72)

When you press this button after memorizing or editing

patterns, the pattern combination will be registered. You

can also recall registered patterns by pressing this button.

!0!0

!0 Elongation button (see page 56)

Stitches #28 to #34 can be elongated up to five times of

their original size.

!1!1

!1 Mirror image button (see pages 59, 72)

Press this button to turnover the selected pattern.

!2!2

!2 Memory button (see pages 12-14, 58-68)

The memory button will memorize your pattern selection.

Press the memory button after you selected the stitch

pattern. (You can program up to 40 patterns.)

!3!3

!3 Clear button (see pages 68, 72)

When this button is pressed, the pattern before or above

the cursor will be deleted.

Press and hold this button to clear the entire pattern

combination.

If this button is pressed after sewing a pattern combination,

the sequence will be deleted.

!4!4

!4 Pattern selection buttons (see page 10)

You can select the stitch patterns directly (mode 1) or by

entering the 2-digit pattern number (mode 2).

!5!5

!5 Buttonhole selection buttons (see page 10)

You can select buttonholes directly in any mode.

!3!1

Mode 1

Screen indication

You can select 10 of the most commonly used patterns

directly by pressing the pattern selection buttons.

Mode 2 and 3

You can select stitch patterns from #01 to #99.

Patterns #01 to #10 in mode 2 are programmable patterns

equivalent to the patterns in mode 1.

Lettering mode

Press this button to enter the lettering mode and select one

of the following fonts or border patterns.

q Block style letters

w Block style European letters

e Script style letters

r Script style European letters

t Broadway style letters

y Broadway style European letters

u Border patterns

Mode selection

When you switch on the machine, the direct select mode

(mode 1) is activated. Press the mode button to change

the mode.

Pattern Selection

Mode 1

You can select the stitch patterns #01 to #10 directly by

pressing the pattern selection buttons.

q Patten selection buttons

The buttonholes BH1 to BH3 cab be directly selected by

pressing the buttonhole selection buttons in any mode.

w Buttonhole selection buttons

The LCD screen shows the standard settings for the

selected stitch pattern.

e Pattern number and image of the selected stitch

r Stitch width or needle drop position

t Stitch length

y Recommended setting for needle thread tension

u Recommended foot pressure

i Recommended presser foot

A triangle mark will appear when a certain utility stitch is

selected. This indicates that there are alternative settings

for the selected stitch (see page 11).

o Recommended presser foot

Mode 2, 3 and Lettering

To select a stitch pattern, enter the 2-digit number of the

desired stitch pattern by pressing the corresponding

number buttons.

Please refer to the stitch chart to find the pattern number of

the desired stitch.

Example: stitch pattern #31

Press the button number “3” and button number “1”.

The pattern number appears for a while.

The LCD screeen shows the selected stitch pattern and

setting information.

Help button

Pressing this button will show alternative applications of the

selected pattern when patterns #01, #04, #06, #08 (mode 1)

or #29 (mode 2) have been selected.

Example: When pattern #01, #04, #06, #08, #29 has been

selected.

Each time you press the help button, the LCD screen will

show as follows:

The zigzag foot and quilting bar for quilting will be shown.

The even foot (optional item) will be shown.

The rolled hem foot for a rolled hem will be shown.

The zipper foot for zipper sewing will be shown.

Customizing Machine Settings

You can customize the machine settings to your

preference.

Turn on the power switch while pressing the memory

button. The machine setting window will appear.

q Memory button

w Power switch

e Machine setting window

Resumption setting

Pattern number 4 will be automatically selected when

turning the power on.

However the last pattern sewn before turning the power off

can be recalled if the resumption setting is selected.

Press button number 1 to select Normal/Resumption

setting.

Press the edit or help button to select either Normal or

Resumption setting.

Press the memory button to enable the setting.

Sound setting

You can change the loudness of buzzer sound.

Press button number “2” to select sound setting. The LCD

screen shows the sound setting.

Press the edit or help button to select the sound level.

Press the memory button to enable the setting.

Language selection

You can choose one of 10 languages for the screen display.

1. English 2. Spanish 3. Finnish 4. French

5. German 6. Italian 7. Dutch 8. Portuguese

9. Russian 10. Swedish

Press the button number “3”.

The LCD screen shows language selection.

Press the edit or help button to select a language.

Press the memory button to set the language.

Pop-up window duration time setting

A pop-up window will appear for a while when selecting

patterns, altering stitch length or width.

The duration of the window displayed can be changed to

suit o your preference.

The default setting is 2 seconds (x1.0).

Press the button number “4”.

The LCD screen shows the pop-up window duration time

setting display.

Press the edit or help button to select the duration.

1.: x 0.5........1 second

2.: x 1.0........2 seconds

3.: x 1.5........3 seconds

Press the memory button to enable the setting.

When turning the power on, the initial display shows the

customized settings that you have made.

Example:

q Language: English

w Resumption setting: ON

e Buzzer sound: Normal

r Pop-up window duration: 2 seconds

Customizing the preset values for the stitch length and

width

The preset value of the stitch length and width are

optimized for each pattern.

You can modify the preset value of the patterns in mode 1

and save it so that you do not have to change the setting

each time you turn the power switch on.

Example: To change the preset value for the stitch

length

Select the stitch pattern you want to change the preset

value.

Press “–” or “+” to change the stitch length.

Press the memory/call button.

Press the memory button to save your personal setting.

A symbol “C” appears on LCD screen to indicate the stitch

has been altered from the factory default settings.

q Symbol “C”

Restoring the original settings

Select the pattern that you have changed its settings.

Press the memory/call button. The LCD screen will show

the current settings.

Press the “C” button. The symbol “C” disappears and the

preset values will return to the original settings (the same

settings when you have purchased the machine).

Presser Foot Lifter

The presser foot lifter raises and lowers the presser foot.

You can raise it about 1/4˝ (0.6 cm) higher than the normal

up position for easy removal of the presser foot, or to help

you place thick material under the foot.

q Presser foot lifter

w Higher position

Changing the Presser Foot

CAUTION:

Turn off the power switch before changing the foot. Always

use the proper foot for the selected pattern. The wrong foot

can cause the needle to break.

• To remove

Raise the needle to its highest position by turning the hand

wheel counterclockwise.

Raise the presser foot, and press the red button on the

back of the foot holder.

• To attach

Place the selected presser foot so that the pin on the foot

lies just under the groove on the foot holder.

Lower the presser bar to lock the foot into place.

Each foot is marked with a letter for identification.

q Snap-on button (red button)

w Groove

e Pin

r Identification letter

Removing and Attaching the Foot Holder

• To remove

Raise the presser foot lifter and remove the thumb screw

by turning it counterclockwise with a screwdriver.

Remove the foot holder.

• To attach

Match the hole in the foot holder with the threaded hole in

the presser bar.

Fit the thumb screw into the hole.

Tighten the screw by turning it clockwise with

a screwdriver.

q Thumb screw

w Foot holder

e Presser bar

Variety of Presser Feet and Their Uses

q Zigzag foot A:

This is the most versatile foot. It can be used for various stitches including

straight stitches and zigzag stitches. It is designed to achieve firm and neat

seam results.

w Overedge foot C:

This foot is exclusively for overedging. The brush on the foot effectively

prevents skipped stitches on the raw edge of fabrics.

e Rolled hem foot D:

This special foot is for sewing a rolled hem. The curl of the foot helps to form a

hem at a constant width.

r Zipper foot E:

This foot is for sewing zippers. The zipper teeth are guided through the grooves

on the bottom of the foot.

t Satin stitch foot F:

This clear plastic foot is ideal for satin stitches and decorative stitches. The

center groove on the bottom of the foot ensures smooth feeding of dense

stitches.

y Blind hem foot G:

This foot is specially designed for blind hemming. The guide on the foot helps

feed the fabric and sew a straight and nearly invisible blind-hem.

u Cording foot H:

This foot is specially designed to hold one or three strands of cording to create

braiding.

i Overcasting foot M:

This foot is specially designed to simulate professional style overlocking. The

wires on the foot effectively prevent the fabric edge from puckering or rolling.

o Darning foot P:

This is a special foot for basting. It holds the fabric while taking a stitch,

synchronizing with the needle bar movement. This foot can also be used for

free motion embroidery or quilting.

!0!0

!0 Automatic buttonhole foot R:

This foot is for buttonholes and for darning. Place a button in the button holder

on the rear of the foot. This automatically sets the buttonhole size.

!1!1

!1 Button sewing foot T:

This foot is exclusively used fir attaching a button. It holds a button securely in

place and allows fine adjustment of button position.

Bobbin Winding

Removing the bobbin

Slide the hook cover plate release button to the right, and

remove the cover plate.

Lift out the bobbin from the bobbin holder.

q Hook cover plate release button

w Hook cover plate

e Bobbin

Setting the spool of thread

Lift up the spool pin.

Place a spool of thread on the spool pin with the thread

coming off the spool as shown.

Attach the large spool holder, and press it firmly against

the spool of thread.

q Spool pin

w Spool of thread

e Large spool holder

The small spool holder is used with narrow or small spools

of thread.

r Small spool holder

Extra spool pin

The extra spool pin is for bobbin winding, without

unthreading the machine, and for twin needle sewing.

Insert the extra spool pin into spool stand and the hole.

Place the felt and a spool on the pin as illustrated.

q Spool

w Extra spool pin

e Spool pin felt

r Spool stand

t Spool pin hole

Bobbin Winding

NOTE:

Set the speed control slider at its fastest position for

bobbin winding.

z Draw the thread from the spool.

Guide the thread around the bobbin winding tension

disk.

Be sure to insert the thread between the tension disks.

q Bobbin winding tension disk

x Insert the thread through the hole in the bobbin,

threading from the inside to the outside.

Put the bobbin on the bobbin winder spindle.

w Bobbin

e Bobbin winder spindle

c Push the bobbin winder spindle to the right.

The LCD screen shows bobbing winding sign.

v With the free end of the thread held in your hand,

depress the foot control. Stop the machine when

the bobbin has wound a few layers, and cut the

thread close to the hole on the bobbin.

b Depress the foot control again. When the bobbin is

fully wound, it will stop automatically.

Return the bobbin to its original position by moving the

spindle to the left, and cut the thread as shown.

Cut the thread with the bobbin thread cutter.

r Bobbin thread cutter

z Place the bobbin in the bobbin holder with the thread

running off counterclockwise.

q Thread

w Bobbin holder

Inserting the bobbin

x Guide the thread into the notch on the front of the bobbin

holder.

e Front notch

c Draw the thread to the left, sliding it between the tension

spring blades.

v Continue to draw the thread lightly until the thread slips

into side notch (B).

r Side notch

b Pull out about 10 cm (4˝) of thread to the rear.

Refer to the threading chart shown on the hook cover

plate. Attach the hook cover plate.

t Hook cover plate

y Threading chart

Threading the Machine

Raise the presser foot lifter.

Turn the power switch on.

Press the up/down needle position button twice to raise

the needle.

q Up/down needle position button

Turn the power switch off.

z Draw the thread around and under the upper thread

guide while holding the thread at the spool.

w Upper thread guide

x Draw the thread down along the right channel.

Then turn around the bottom of the guide plate.

e Guide plate

c Firmly draw the thread up to the take-up lever.

Slip the thread through the slit and into the eye of the

take-up lever.

r Slit

t Eye of take-up lever

v Then down through the lower thread guide.

y Lower thread guide

b Slide the thread behind the needle bar thread guide

on the left. Thread the needle from front to back or use

the needle threader.

u Needle bar thread guide.

Thread the needle using the needle threader (see the next

page).

Built-in needle threader

NOTE:

The needle threader can be used with a #11 to #16

needle, or a #11 Blue needle.

Thread size 50 to 90 is recommended.

z Lower the presser foot. Raise the needle to its highest

position.

Push down the needle threader knob as far as it will go.

The hook comes out through the needle eye from

behind.

q Knob

w Hook

x Draw the thread from the right to the left, under the

guide (A), threader hook and the guide (B).

e Guide (A)

w Hook

c Draw the thread up along the right side of the guide (B)

and slip the thread in between the guide (B) and holder

plate.

r Guide (B)

t Holder plate

v Release the knob slowly so a loop of the thread is

pulled up through the needle eye.

b Pull the thread end through the needle eye.

Drawing Up Bobbin Thread

z Raise the presser foot. Hold the needle thread lightly

with your left hand.

v Pull both threads 4˝ to 6˝ (10 to 15 cm) under and

behind the presser foot.

x Press the up/down needle position button twice to

lower and raise the needle.

q Up/down needle position button

c Pull the needle thread to pick up the bobbin thread.

w Needle thread

e Bobbin thread

Changing the Needle

CAUTION

Always make sure to turn the power switch off and

disconnect the machine from power supply before

changing the needle.

• Removing the needle

Turn the power switch off.

Raise the needle to its highest position by turning the

hand wheel. Lowering the presser foot.

Loosen the needle clamp screw by turning it

counterclockwise.

Remove the needle from the needle clamp.

q Needle clamp screw

w Needle clamp

• Attaching the needle

Insert a new needle into the needle clamp with the flat side

to the rear.

Push the needle up as far as it goes.

Tighten the needle clamp screw firmly by turning it

clockwise.

e Flat side

• Checking the needle

To see if the needle is good, place the flat side of the

needle onto something flat (needle plate, glass, etc.).

The gap between the needle and the flat surface should be

consistent. Never use a bent or blunt needle.

A damaged needle can cause permanent snags or runs in

knits, fine silks and silk-like fabrics.

r Gap

Fabric

Light

Thread

Needle

Medium

Heavy

Lawn

Georgette

Tricot

Wool,

Polyester

Cotton,

Polyester

Fine jersey

Wool

Denim

Jersey

Coating

Quilting

Silk #80-100

Cotton #80-100

Synthetic #80-100

Silk #50

Cotton #60-80

Synthetic #50-80

Cotton #50

Silk #50

Cotton #40-50

Synthetic #40-50

Silk #30

Cotton #50

#9/65–11/75

#11/75–14/90

#14/90

#14/90–16/100

#16/100

Needle and thread chart

• Auto-thread tension

When the thread tension dial is set at AUTO for automatic

thread tension, the green light will be on.

For general sewing, set the tension dial at AUTO, which

covers a wide range of sewing conditions.

Align the AUTO mark of the thread tension dial with the

indication line.

The green light turns on.

q Green light

• Balanced thread tension

For straight stitch sewing, both needle and bobbin threads

will join at the middle of the fabric.

For zigzag stitch sewing, the needle thread will appear

slightly on the wrong side of the fabric.

q Wrong side of fabric

w Right side of fabric

e Bobbin thread

r Needle thread (Top thread)

Balancing Thread Tension

• Manual thread tension adjustment

You should adjust the tension manually if the green light

blinks when a specific stitch is selected.

The LCD screen shows a recommended tension setting for

the selected stitch.

The tension setting also blinks until you set the tension

manually.

q Green light

w Recommended tension setting

You may also need to adjust tension manually depending on

the sewing condition such as type of the fabric and number

of layers.

If the needle thread is too tight, the bobbin thread appears

on the right of the fabric.

q Wrong side of fabric

w Right side of fabric

e Bobbin thread

r Needle thread (Top thread)

Turn the thread tension dial to the lower number to decrease

the thread tension.

If the needle thread is too loose, the needle thread loops

on the underside of the fabric.

q Wrong side of fabric

w Right side of fabric

e Bobbin thread

r Needle thread (Top thread)

Turn the thread tension dial to the higher number to

increase the thread tension.

Dropping and Raising the Feed Dog

The drop feed lever is located underneath the free arm bed

on the back side of the machine.

q Drop feed lever

• To drop the feed dog, push the lever in the direction of the

arrow w, as illustrated.

w To drop the feed dog

• To raise the feed dog, push the lever in the direction of the

arrow e, as illustrated, and turn the hand wheel toward

you. The feed dog must be up for normal sewing.

e To raise the feed dog

Pressure Adjusting Lever

Foot pressure can be adjusted with the pressure adjusting

lever located inside the face cover.

The pressure adjusting lever should be set at “3” for regular

sewing.

Reduce the pressure to “2” for applique, cut work, drawn

work, basting and embroidery.

Set the pressure to “1” when sewing chiffon, lace, organdy

and other fine fabrics.

Velour and knits with a lot of stretch may also require a “1”

setting.

Open the face cover and set the lever at the desired

number.

q Pressure adjusting lever

BASIC AND UTILITY STITCHES

Straight Stitches

Straight stitch in center needle position

q Pattern: #1 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

NOTE:

When stitch pattern #01, #02 or #03 is selected, the sub

needle plate will close to set up the needle hole for straight

stitch.

q Sub needle plate

w Needle hole

The needle drop position of patterns #01, #02 and #03

cannot be changed.

To sew

Raise the presser foot and position the fabric next to a

seam guide line on the needle plate. Lower the needle to

the point where you wish to start.

Pull the needle and bobbin threads toward the rear.

Lower the presser foot.

Depress the foot control or press the start/stop button to

start sewing. Gently guide the fabric along the seam guide

line letting the fabric feed naturally.

NOTE:

When you press the start/stop button once, the machine

starts running slowly for the first few stitches, then runs at

the speed set by the speed control slider.

The machine runs slowly as long as you press and hold the

start/stop button.

Sewing on heavy fabric

The black button on foot A will lock the foot in a horizontal

position if you push it in before lowering the presser foot.

This ensures even feeding at the beginning of seams and

helps when sewing many layers of fabric such as sewing

over welt seams when hemming jeans.

When you reach a point of increased thickness, lower the

needle and raise the presser foot. Press the toe of the foot

and push in the black button, then lower the foot and

continue sewing. The button will be released after a few

stitches.

q Black button

Securing a seam

For fastening the end of seam, press the reverse button and

sew several reverse stitches.

The machine sews in reverse as long as you press and hold

the reverse button.

Press the reverse button once when sewing the Lock-a-Matic

stitch (pattern #02) or locking stitch (pattern #03) so the

machine will lock the stitch off and stop automatically.

Cut the thread by using the thread cutter.

The threads are cut the proper length for starting the next

seam.

q Thread cutter

Using the seam guides on the needle plate

The seam guides on the needle plate are engraved to help

you measure seam width. The number on the needle plate

indicates the distance between the center needle position

and the edge of the fabric. The lines are 1/8˝ (0.3 cm) apart,

and engraved at 3/8˝, 4/8˝, 5/8˝ and 6/8˝. The lines in milli-

meters are 5 mm apart, and are engraved at 10 mm, 15 mm

and 20 mm.

q Seam width

w Needle drop position

e Edge of fabric

r Needle plate guide lines

Turning a square corner

To maintain a 5/8˝ seam allowance after turning a square

corner, use the cornering guide on the needle plate.

1. Stop sewing when the front edge of fabric reaches the

cornering guide lines.

2. Lower the needle by pressing the up/down needle

position button.

3. Raise the presser foot and turn the fabric

counterclockwise 90°.

4. Lower the presser foot, and begin stitching in the new

direction.

q Cornering guide

Using the quilting guide

The quilting bar will help keep the seam lines evenly spaced.

Use the seam guide lines on the needle plate, and the free-

arm, to help determine the distance between quilting

stitches.

Loosen the quilting bar screw on the back of the foot holder.

Insert the quilting bar into the hole under the screw. Set the

quilting bar at the desired position and tighten the screw.

Sew tracing the previous seam with the quilting bar.

q Quilting bar screw

w Quilting bar

e Seam guide lines

Adjusting the needle drop position

The needle drop position of the straight stitch patterns,

#04, #05, #27, #36-#43, #46, #48-51can be changed by

pressing the stitch width adjustment button.

Press the right side of the button (+ sign) to move the

needle bar to the right.

Press the left side of the button (– sign) to move the needle

bar to the left.

Adjusting the stitch length

The stitch length can be altered by pressing the stitch

length adjustment button.

The stitch length indication will change as the button is

pressed.

Press the right side of the button (+ sign) to increase the

stitch length.

Press the left side of the button (– sign) to decrease the

stitch length.

Straight stitch in left needle position

q Pattern: #4 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

Use this stitch to seam the fabrics along the edge.

1.0 5.0

7.03.5

0.0

Lock-a-Matic stitch

q Pattern: #3 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

Locking stitch

q Pattern: #2 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

This unique stitch is used where an invisible locking stitch

is needed.

Lower the needle close to the front edge of the fabric.

The machine will sew several locking stitches in place and

continue sewing forward.

When you press the reverse stitch button at the end of the

seam, the machine will sew several locking stitches in

place, then stop sewing automatically.

Use it to reinforce areas such as crotch and armhole

seams, as well as when constructing items such as back-

packs for extra strength.

Press the reverse stitch button once, when you reach the

end of the seam.

The machine will sew four reverse stitches, four forward

stitches, and then stop sewing automatically.

Triple stretch stitch

q Pattern: #5 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

This strong, durable stitch is recommended for areas where

both elasticity and strength are needed to ensure comfort

and durability.

Use it to reinforce areas such as crotch and armhole

seams.

Also use it when constructing items such as backpacks for

extra strength.

Stretch stitch

q Pattern: #0 (mode 1) or #10 (mode 2)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

This is a narrow stretch stitch designed to eliminate

puckering on knit fabrics and bias seams, while permitting

the seam to be pressed completely open and flat.

Variety of Straight Stitches

Patchwork piecing stitch

q Pattern: #39 (mode 2)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

This is straight stitch with 1.8 mm stitch length, ideal for

patchwork piecing.

Pattern #43 (mode 2) is the patchwork piecing stitch with

left needle drop position.

French knot

q Pattern: #48 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: 5-8

Combine this stitch with patterns#36-38 to program French

knots.

Saddle stitch

q Pattern: #51 (mode 2)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

You can achieve a lovely hand-worked look when

topstitching suits, blazers, jumpers and denim outfits with

the saddle stitch.

New sculpture stitch

q Pattern: #49 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

This decorative stitch adds a three dimensional effect when

outlining designs.

Decorative stitch

q Pattern: #50 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

Use this stitch for quilting or decorative stitching.

Zipper Sewing

q Pattern: #1 (mode 1)

w Presser foot: Zipper foot E

e Thread tension: AUTO

Attaching the zipper foot

Fit the pin on the zipper foot into the groove on the foot

holder.

• To sew the left side of the zipper, attach zipper foot with

the right-hand side of pin.

• To sew the right-side of zipper, attach zipper foot with

the left-hand side of pin.

q Groove

w Pin

e To sew left side

r To sew right side

Fabric preparation

Add 1 cm (3/8˝) to the zipper length. This is the overall

opening size.

Place the right sides of the fabric together and sew up

to the end of the zipper opening, with a 2 cm (13/16˝)

seam allowance. Reverse the stitch to fasten the

seam. Baste along the zipper opening with the stitch

length 4.5

q Right side of the fabric

w 1 cm (3/8˝)

e Opening size

r Zipper length

t Slider

y Zipper teeth

u Zipper tape

i Wrong side of the fabric

o End of the opening

!0 2 cm (13/16˝)

!1 Zipper opening (Basting)

!22 Reverse stitches

!3 End of the opening

!4 Seam

NOTE:

Loosen the thread tension to one (1) for the basting

stitch.

To sew

z Fold up the upper seam allowance. Fold back the

bottom seam allowance to form a 0.3 cm (1/8˝)

fold. Place the zipper teeth next to the fold and pin

it in place.

q Bottom fabric

w End of the zipper opening

e Zipper teeth

r 0.3 cm (1/8˝)

t Wrong side of the upper fabric

y Opening size

u Fold

Zipper Sewing (continued)

x Attach the foot with the pin on the right. Sew

through all the layers from the end of the zipper

opening, guiding the zipper teeth along the edge of

the foot.

c Stop the machine 5 cm (2") before the foot reaches

the slider on the zipper tape. Lower the needle into

the fabric, and raise the foot. Open the zipper, then

lower the foot and stitch the remainder of the

seam.

i Slider

o 5 cm (2")

v Close the zipper and open the upper fabric flat over

the zipper. Baste the upper fabric and zipper tape

together.

!0 Basting stitch

b Detach the foot and attach it with the pin on the

left. Backstitch across the end of opening to 1 cm

(3/8"). Turn the fabric 90 degrees and stitch

through the garment and zipper tape.

!1 Backstitch

n Stop the machine 5 cm (2") before the foot reaches

the slider on the zipper tape. Lower the needle into

the fabric, and raise the foot. Remove the basting

stitches.

!2 Basting stitches

m Open the zipper, then lower the foot and stitch the

remainder of the seam.

After finish sewing, remove the basting stitches on

the upper fabric.

b n

Basting

q Pattern: #27 (mode 2)

w Presser foot: Darning foot P

e Thread tension: 1–3

r Feed dog: Lowered

t Foot pressure: 1

Attaching the darning foot

Raise the needle.

Remove the foot holder by loosening the thumb screw.

Attach the darning foot on the presser bar putting the pin

on the needle clamp. Tighten the thumbscrew firmly with a

large screwdriver.

q Foot holder

w Thumb screw

e Pin

r Needle clamp

To sew

Lower the feed dog.

Set the thread tension dial between 1 and 3.

Put some fabric under the foot and press up/down needle

position button twice to bring the needle thread down

through the hole in the foot.

Pull the fabric and thread to the rear. Lower the presser

foot.

Press down the foot control. The machine stops after each

stitch.

Move the fabric to where you want the next stitch.

Repeat steps to to sew. After finishing sewing, pull the

threads and fabric to the rear side.

* After sewing, reset tension to “AUTO”. Return feed dog

lever to raised position. Feed dog will rise when sewing

resumes.

To sew:

Fold the edge of the fabric twice, 6 cm (2 3/8˝) in length

and 0.3 cm (1/8˝) in width.

Trim the corner 0.5 cm (3/16˝) by 0.8 cm (1/4˝) for easier

insertion of the hem into the foot.

Position the fabric aligning the edge of hem with the guide

on the foot.

Lower the foot and sew 1–2 cm (1/2˝ – 1˝) while pulling

both threads to the back.

Stop the machine with the needle down in the fabric. Raise

the foot and insert the folded portion of the fabric into the

curl of the foot.

Lower the foot, and then sew by lifting up the edge of the

fabric to keep it feeding smoothly and evenly.

Rolled Hem

q Pattern: #1 (mode 1)

w Presser foot: Rolled hem foot D

e Thread tension: AUTO

Zigzag Stitch

q Pattern: #6 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

Zigzag stitch is useful for overcasting, applique, mending

etc.

Changing the stitch width

Press the stitch width button to change the stitch width.

Press the right side of the button (+ sign) to increase the

stitch width.

Press the left side of the button (– sign) to decrease the

stitch width.

Changing the stitch length

Press the stitch length button to change the stitch length.

Press the right side of the button (+ sign) to increase the

stitch length.

Press the left side of the button (– sign) to decrease the

stitch length.

Pattern #35 (mode 2) has a fixed right needle drop

position.

When you change the stitch width the right needle drop

position will change.

2.0 7.0

1.0

5.0

Overcasting

q Pattern: #6 (mode 1)

w Presser foot: Overedge foot C

e Thread tension: AUTO

This zigzag variation is very useful in garment construction

and in finishing raw edges of any sewing project.

z The black ridge and the guide wires on the overedge

foot keep the edge neat and the fabric straight.

x Place your fabric so that the double guide wires come

to the edge. The machine will stitch over these wires.

The black ridge will keep the loose threads in so that

the needle can stitch over them.

c As you sew, be sure your fabric edge pushes up

against the black ridge.

CAUTION:

When using an Overedge foot, make sure to set the stitch

width between 5 and 7, otherwise the needle may hit the

overedge foot.

Tricot Stitch

q Pattern: #7 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

This stitch is used to finish the seam allowance on

synthetics and other fabrics that tend to pucker. The stitch

is also excellent for darning and mending tears.

Place your fabric to allow a 5/8˝ (1.5 cm) seam. Trim

excess close to stitching. Be careful not to cut the

stitches.

Overedge Stitch

q Pattern: #8 (mode 1)

w Presser foot: Overedge foot C

e Thread tension: AUTO

This stitch pattern combines the straight and the zigzag

stitches, using the overedge foot, to stitch and overcast

seams in one step.

It is ideal for 0.6 cm (1/4" ) seams on knits (when

attaching ribbing) or on medium to heavyweight woven

fabrics where you want a narrow seam.

Place your fabric so that the raw edges fit under the wire

guides and touch the black ridge.

NOTE:

Stitch width cannot be set narrower than 4.5.

Knit Stitch

q Pattern: #11 (mode 2)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

This stitch is recommended for sewing such fabrics as

synthetic knits and stretch velour, as it provides the

greatest amount of elasticity and strength.

Sew along the fabric edge leaving an adequate seam

allowance.

After sewing, trim the seam allowance close to the stitches.

Double Overedge Stitch

q Pattern: #12 (mode 2)

w Presser foot: Overedge foot C

e Thread tension: AUTO

This is an excellent stitch for fabrics that tend to ravel

extensively such as linens and gabardines.

Two rows of zigzag stitches are simultaneously sewn over

the edge to insure that fabric will not ravel.

Place the fabric edge next to the guide of the foot and then

sew.

NOTE:

Stitch width cannot be set narrower than 4.5.

Overlock Stitch

q Pattern: #13 (mode 2)

w Presser foot: Overcast foot M

e Thread tension: 6-8

This stitch finishes the edges of fabric similar to a

commercial overlocking machine for a professional look.

Place the fabric edge next to the guide of the foot and then

sew.

NOTE:

Stitch width cannot be changed.

Blind Hem

q Pattern: #9 (mode1) or #14 (mode 2)

w Presser foot: Blind hem foot G

e Thread tension: AUTO

Select pattern #9 for woven fabrics or pattern #14 for

elastic fabrics.

How to fold the fabric

Fold the fabric to make a hem as shown.

q Heavy fabric

w Fine to medium fabric

e 0.4–0.7 cm (3/16˝–1/4˝)

r Overcasted edge of fabric

t Wrong side of fabric

To sew

Position the fabric so that the fold comes to the left side of

the guide on the foot.

Lower the presser foot.

Adjust the position of the needle swing with the stitch width

adjustment button so that the needle just pierces the

folded edge of the fabric when the needle comes over to

the left side.

Sew guiding the fold along the guide.

y Guide on the foot

u Fold

NOTE:

The stitch width of the patterns cannot be changed, but the

needle drop position will move.

Open the fabric with the right side up.

The stitches on the right side of the fabric are almost

invisible.

i Right side of the fabric

Changing needle drop position

Press the stitch width adjustment button.

The LCD screen shows the left needle position from the

guide in millimeters.

Press “–” to move the needle to the right.

Press “+” to move the needle to the left.

q Left needle drop position

w Guide on foot

e Distance between the left needle position and the

guide

NOTE:

You can lengthen a straight portion of the blind stitch by

inserting an extender stitches (see page 63).

Button Sewing

q Pattern: #23 (mode 2)

w Presser foot: Button sewing foot T

e Thread tension: AUTO

r Feed dog: Lowered

Attaching the button sewing foot T

Insert the rear pin on the foot into the groove of the foot

holder.

Gently lower the presser foot lifter while holding the foot

with your fingers.

q Rear pin

w Groove of the foot holder.

To sew

Place a button on the fabric and lower the needle by

turning the hand wheel with your hand, so that the

needle enters through the left hole in the button.

Align the direction of button and lower the button sewing

foot T to hold the button in place.

Press the up/down needle button to bring the needle up

to the highest position. Adjust the stitch width, so that the

zigzag width matches the span of holes in the button.

Press the start/stop button to sew and the machine will

stop automatically.

Cut the needle thread at the beginning.

q Needle thread at the beginning

Pull the bobbin thread to pull the needle thread to the

wrong side off the fabric.

w Needle thread

e Bobbin thread

Tie both threads together.

* Raise the feed dog after sewing.

Buttonholes

Variety of buttonholes

Square Buttonhole

This square buttonhole is widely used on medium to heavy weight fabrics.

The buttonhole size is automatically determined by placing a button in the

foot.

Round-end Buttonhole

This buttonhole is used on fine to medium weight fabrics especially for blouses

and children’s wears.

Fine Fabric Buttonhole

This buttonhole is rounded at both ends and is used on fine, delicate fabrics

such as fine silk.

Keyhole Buttonhole

The Keyhole Buttonhole is widely used on medium to heavy weight fabrics. It

is also suitable for large and thick buttons.

Round Keyhole Buttonhole

A variation of the keyhole buttonhole.

Tailor-made Buttonhole

This buttonhole is ideal for heavyweight fabrics and large and thick buttons.

Stretch Buttonhole

This buttonhole can be used on stretch fabrics. It can also be used as a decorative

buttonhole.

Knit Buttonhole

This buttonhole is suitable for knit fabrics. It can be used as a

decorative buttonhole.

Faux Chain Buttonhole

Resembles a “Hand Worked” buttonhole. Ideal on fine fabrics featured in Heirloom

sewing or for couture fashions.

Welted Buttonhole

This is a template pattern for the hand sewn welted (bound) buttonhole.

Square buttonhole

To sew

z Press the up/down needle position button to raise the

needle.

Attach the automatic buttonhole foot R snapping the

pin into the groove of the foot holder.

q Groove

w Pin

NOTE:

The size of the buttonhole is automatically set by placing a

button in the rear of automatic buttonhole foot R.

The button holder of the foot takes a button size of 1 cm

(3/8˝) to 2.5 cm (1˝) in diameter.

It is sometimes necessary to change buttonhole size to

match certain heavy or specific fabrics and threads.

Make a test buttonhole on an extra piece of the fabric to

check your settings.

The preset width of the buttonhole is suitable for ordinary

buttons.

Apply an interfacing to stretch or fine fabrics.

x Pull the button holder to the back, and place the

button in it. Push it together tightly to the button.

NOTE:

If the button is extremely thick, make a test buttonhole on

an extra piece of the fabric.

If it is difficult to fit the button through the test buttonhole,

you can lengthen the buttonhole by pulling the button

holder back a little. The length of the buttonhole will be

increased.

e Button holder

r Pull back a little

q Pattern: BH1

w Presser foot: Automatic buttonhole R

e Thread tension: AUTO

c Pull the buttonhole lever down as far as it will go.

q Buttonhole lever

NOTE:

If you start sewing without pulling down the buttonhole

lever, the LCD screen will show a warning and the

machine will stop after a few stitches. Pull the buttonhole

lever down and restart the machine.

v Insert the corner of the fabric under the foot. Press

the up/down needle button twice.

Remove the fabric to the left to draw the needle

thread through the hole of the foot.

Place the garment under the foot, and lower the

needle at the starting point of the buttonhole mark.

Then lower the automatic buttonhole foot R.

w Buttonhole mark

e Starting point

NOTE:

Make sure there is no gap between the slider and front

stopper, otherwise the left and right lengths will be

different.

r Slider

t Front stopper

y Difference

b Start the machine to sew the buttonhole.

The buttonhole will be automatically sewn.

Step 1: The machine will sew the front bartack and the left

row first.

Then it goes back o the starting point with straight

stitch.

Step 2: The machine will sew the right row.

Step 3: The machine will sew the back bartack, and the

machine will stop automatically.

n When buttonhole sewing is finished, push the buttonhole

lever upward as far as it will go.

NOTE:

To make a solid and sturdy buttonhole, sew another layer of

buttonhole over the previous stitches.

After the buttonhole is finished, simply start the machine

again.

Do not raise the foot or buttonhole lever.

The machine will sew another layer of buttonhole and stop

automatically when it is completed.

m Remove the fabric and place a pin just below the bartack

at each end to prevent accidentally cutting stitches.

Cut the opening with the seam ripper.

Use an Eyelet puncher to open a keyhole buttonhole

q Seam ripper

w Eyelet puncher

Step 3

Step 1

Step 2

Adjusting buttonhole width

Press the stitch width adjustment button to change the

buttonhole width

Press on “+“ to increase the buttonhole width.

Press on “–“ to decrease the buttonhole width.

The range of adjustment is 2.5 to 7.0.

q Stitch width adjustment button

w Narrower buttonhole

e Wider buttonhole

Adjusting stitch density

Press the stitch length adjustment button to change the

stitch density.

Press on “+” to make the buttonhole stitch coarser.

Press on “–“ to make the buttonhole stitch denser.

The range of adjustment is 0.2 to 0.8.

q Stitch length adjustment button

w Denser buttonhole

e Coarser buttonhole

NOTE:

To alter the buttonhole width and density while sewing a

test buttonhole, stop the machine at the left or right row of

the buttonhole then adjust the stitch width and density to

find the appropriate settings.

Press the memory button so that you can sew a buttonhole

with the new settings.

The setting will return to the preset value when the power

switch is turned off or selecting another stitch.

Corded buttonhole

q Pattern: BH1

w Presser foot: Automatic buttonhole R

e Thread tension: AUTO

To sew a corded buttonhole, follow the same procedure as

for a square buttonhole.

With the automatic buttonhole foot R raised, hook the

filler cord on the spur at the back of the buttonhole foot.

Bring the ends of cord toward you under the buttonhole

foot clearing the front end.

Hook the ends of the filler cord into the forks on the front

of buttonhole foot to hold them tight.

q Spur

w Forks

Lower the needle into the garment where the buttonhole

will start and lower the foot.

Lower the buttonhole lever and buttonhole foot.

Start the machine and sew the buttonhole over the filler

cord.

The machine stops automatically when finished.

Remove the fabric from the machine and cut the sewing

threads.

Pull the end of the filler cord to tighten it.

Thread the end of the cord through a darning needle and

draw it to the wrong side of the fabric and cut.

NOTES:

Set the stitch width in accordance with the thickness of the

filler cord used.

To cut the buttonhole opening, refer to page 44.

If the filler cord is stitched to the fabric and cannot be

pulled, cut it at both ends.

Round-end buttonhole

q Pattern: BH2

w Presser foot: Automatic buttonhole R

e Thread tension: AUTO

Adjusting buttonhole width

Press the stitch width adjustment button to change the

buttonhole width.

Press “+” to make the buttonhole wider.

Press “–” to make the buttonhole narrower.

The range of adjustment is 2.5 to 5.5.

q Stitch width 2.5

w Stitch width 4.0

e Stitch width 5.5

Keyhole buttonhole

q Pattern: BH3

w Presser foot: Automatic buttonhole R

e Thread tension: AUTO

Adjusting buttonhole width

Press the stitch width adjustment button to change the

buttonhole width.

Press “+” to make the buttonhole wider.

Press “–” to make the buttonhole narrower.

The range of adjustment is 5.5 to 7.0.

q Stitch width 5.5

w Stitch width 6.5

e Stitch width 7.0

The sewing sequence is as shown.

The sewing sequence is same as that of square buttonhole

(see page 43).

Knit buttonhole

q Pattern: #20 (mode 2)

w Presser foot: Automatic buttonhole R

e Thread tension: AUTO

Faux chain buttonhole

q Pattern: #21 (mode 2)

w Presser foot: Automatic buttonhole R

e Thread tension: AUTO

The range of buttonhole width adjustment is 2.5 to 7.0.

The range of stitch density adjustment is 0.7 to 1.2.

The sewing sequence is as shown.

The range of buttonhole width adjustment is 2.5 to 7.0.

The range of stitch density adjustment is 0.5 to 2.5.

Eyelet

q Pattern: #26 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

The eyelet is used for belt holes etc.

To sew

Depress the foot control to sew.

The machine will sew an eyelet and stop automatically

when completed.

Open the eyelet with an awl, punch or pointed scissors.

Adjusting the shape of an eyelet

Correct the shape of the eyelet as follows:

q If the eyelet gap opens, press “–“ on the stitch length

adjustment button.

w If the eyelet overlaps, press “+“ on the stitch length

adjustment button.

NOTE:

The shape can be adjusted within L1 to L3 (default setting

is L2).

Darning

q Pattern: #24 (mode 2)

w Presser foot: Automatic buttonhole foot R

e Thread tension: AUTO

Pull the button holder to the rear as far as it will go.

q Button holder

Place the garment under the foot.

Press the up/down needle position button twice.

Remove the fabric to the left to draw both threads under

the foot and place the fabric back under the foot.

Lower the needle at the starting point, then lower the foot.

w Starting point

Depress the foot control and the machine will sew a

darning 2 cm (3/4˝) long and stop automatically.

Repeat sewing in a different direction until the darning

covers the rip or hole.

NOTE:

The maximum size of darning is 2 cm (3/4˝) long and 0.7

cm (1/4˝) wide.

e Maximum length 2 cm (3/4˝)

r Maximum width 0.7 cm (1/4˝)

t Starting point

To sew a shorter darning

To sew a darning shorter than 2 cm (3/4˝), first stop the

machine after sewing the required length, then press the

reverse button.

The required length has been determined.

Start the machine again and continue sewing until the

machine stops automatically.

q Required length

w Starting point

e Reverse stitch button

To sew the same size darning

Simply start the machine to sew another darning at the

same size.

To sew the darning at a different size

Press the memory button and start sewing from the

beginning.

To adjust the evenness of darning

The evenness of darning may vary depending on the

sewing conditions, such as type of fabrics, number of

layers etc. You can correct the unevenness of darning with

the stitch length adjustment button.

If the left corner is lower than the right side, press “–” to

correct it.

If the right corner is lower than the left side, press “+” to

correct it.

NOTE:

The evenness can be adjusted within d1 to d9 (default

setting is d5).

Tacking

q Pattern: #25 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

Tacking is used to reinforce pockets, crotches and belt

carriers where extra strength is needed.

To sew

Depress the foot control until the machine stops

automatically.

The machine will sew a tacking 1.5 cm (9/16˝) long auto-

matically.

q 1.5 cm (9/16 ˝)

To sew a shorter tack

To sew a tack shorter than 1.5 cm (9/16˝), first stop the

machine after sewing the required length, and then press

the reverse stitch button.

The required length has been determined.

Start the machine and continue sewing until the machine

stops automatically.

w Starting point

e Required length

r Reverse stitch button

t Tack length

To sew the same size tack

To sew another tack at the same size, simply start the

machine and it will stop automatically when finished

sewing.

To sew a tack at a different size

To sew the next tack in a different size, press the memory

button and start sewing. Press the reverse stitch button

after sewing the required length.

The required length has been determined.

QUILTING AND DECORATIVE STITCHES

Quilting

q Pattern: #1 (mode 1)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

Attach the quilting bar (see page 27).

Sew while tracing the previous seam with the quilting

bar.

Free motion quilting

q Pattern: #4 (mode 1)

w Presser foot: Darning foot P

e Thread tension: AUTO

r Feed dog: Lowered

t Foot pressure: 1

Lower the feed dog (see page 25).

Attach the darning foot (see page 33) and reduce the

foot pressure (see page 25).

Baste or pin the quilt layers together.

Draw a design on the top fabric with a washable marker.

Move the quilt layers slowly and evenly while stitching

along the design marked on the fabric.

Seam the fabrics right sides together with straight stitch.

Press seam allowance open.

Select the desired stitch and sew on the right side of

garment centering over the seam line.

Patchwork

q Pattern: #71-#74 (mode 2)

#15, #65-#68, #71, #72 (mode 3)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

Pintucking

q Pattern: #4 (mode 1)

w Presser foot: Blind hem foot G

e Thread tension: AUTO

Fold a fabric with the right side together.

Place the folded fabric under the blind hem foot.

Align the edge of the fold with the guide on the foot, and

lower the foot.

Sew while guiding the edge of the fold along the guide.

Open the fabric and press the tuck to one side.

Applique

q Pattern: #35, #62-#68 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

r Foot pressure: 2

Place an applique on the fabric and baste or pin it in place.

Reduce the foot pressure.

Sew while guiding the fabric so the outer edge of the

applique aligns with the slit of the foot.

q Applique

w Slit

e Outer edge

Wen turning around a corner, stop the machine and press

the up/down needle position button to lower the needle at

the outer edge of the applique.

Raise the presser foot and pivot the fabric around te

needle to change the sewing direction.

NOTE;

The stitch width of patterns #65-67 is fixed, but the needle

drop position will move to the left or right by pressing the

stitch width adjusting button.

Smocking is a delicate decorative treatment used on

children’s wears or women’s blouses.

Choose a soft and lightweight fabric such as batiste,

gingham or challis. Cut the fabric three times wider than

the projected width.

Reduce the thread tension to “0” and set stitch length at

“5.0” .

Sew rows of straight stitches 1 cm (3/8”) apart across the

area to be smocked.

Knot the threads along one edge. From the other edge,

pull the bobbin threads (bottom threads) to distribute the

gathers evenly.

Sew the smocking stitches between the gathered rows.

Remove the straight stitches between the gathered rows.

Smocking

q Pattern: #52, #79, #80, #85, #86 (mode 2)

#15 (mode 3)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

Sew scallops 1 cm(3/8”) from folded edge.

Trim the allowance close to the stitches.

Make sure not to cut the stitches.

Scallop

q Pattern: #69 (mode 2)

w Presser foot: Zigzag foot A

e Thread tension: AUTO

Use a lightweight fabric (tricot, for example).

Fold the fabric in bias as shown and stitch on the fold.

Increase the thread tension.

Allow the needle to just clear the folded edge to create a

shelled edge.

If you sew rows of shell stitches, space the rows at least

1.5 cm (5/8”) apart. You can also sew shell stitches on

knits or soft silky woven fabrics, in any direction.

Shell Tuck

q Pattern: #15 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: 6-8

Cording

q Pattern: #29 (mode 2)

w Presser foot: Cording foot H

e Thread tension: AUTO

3-strand cording

Insert 3 strands of cording under the spring of the foot and

draw them under the foot to the rear.

Hold the three strands parallel for even sewing and be sure

to sew over the strands.

Stitch slowly and smoothly, guiding the fabric as you sew.

q Spring

1-strand cording

Insert 1 strand of cording under the spring of the foot and

draw it under the foot to the rear (use the center slot of the

spring).

Select pattern #6 (mode 1), then decrease the stitch width

and sew.

Use this stitch to join two pieces of fabric to create an open

work appearance and add design interest.

Fold under each fabric edge 5/8˝ (1.5 cm) and press. Pin

the two edges to paper or tear away backing 1/8˝ (0.3 cm)

apart. Sew slowly, guiding the fabric so the needle catches

the folded edge on each side.

After finishing sewing, tear away the paper.

Fagoting

q Pattern: #56, #77, #78, #85, #86 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

Satin Stitches

q Stitch pattern #28-#34 (mode 2)

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

Satin stitches can be elongated up to

five times their normal length by pressing the elongation

button.

The stitch width and length can also be changed.

Select the desired satin stitch.

Press the elongation button to change the elongation ratio.

Elongation ratio is indicated in multiples of the original

pattern length.

NOTE:

If you press the elongation button when any stitch other

than satin stitches, buzzer sounds and a warning message

will appear.

Twin Needle Sewing

Machine settings

q Pattern: See the list below.

w Presser foot: Satin stitch foot F

e Thread tension: AUTO

NOTES:

* When you sew patterns with the twin needle, press the

twin needle button and test the stitches first before you

begin to sew.

* Use the zigzag foot A or satin stitch foot F for twin needle

sewing.

* Turn off the machine before changing the needle.

Use the extra spool pin and spool stand.

Threading the machine for twin needle sewing

Place two spools of thread, one on the horizontal spool pin

and the other on the extra spool pin as shown.

Draw both threads from the spools and thread them

through the points from z to n.

Make sure that the two strands of thread do not get

tangled.

Turn the power switch on and press the twin needle button

Select a pattern and sew.

NOTES:

* The stitch width is limited to 3 mm or less.

* The stitch patterns shown to the left can be sewn with the

twin needle.

* If a selected pattern is not for twin needle, a buzzer

will sound and a message will appear on the LCD screen.

Mode 2

Mode 3

PROGRAMMING PATTERNS AND LETTERS

Programming the Pattern Combination

Example: Patterns #31 and #32 (mode 2)

Select pattern 31 (mode 2).

Press the memory button.

Select the pattern 32 (mode 2).

Press the memory button.

A series of pattern combination will be sewn.

NOTE:

If you press the memory button when the patter cannot be

programmed, a buzzer sounds and a waring message will

appear.

Programming the mirror image patterns

Example: Pattern #32 and its mirror image

Select pattern #32 (mode2).

Press the memory button.

Pattern #32 is memorized.

Select pattern #32 (mode 2) again.

Press the mirror image button.

Pattern #32 is turned over.

Press the memory button.

A mirror image of pattern #32 is memorized.

Programming the locking stitch

Example: Pattern #31 (mode 2) with locking stitch.

Select pattern #31 (mode 2).

Press the memory button.

Pattern #31 is memorized.

Select pattern #98 (mode 2)

Press memory button.

Pattern #98 (locking stitch) is memorized.

Press the start/stop button so the machine will sew pattern

#31 and lock the stitch off then stop automatically.

q Locking stitch

Sewing a pattern combination from the beginning

Sewing the current pattern from the beginning

If you have to stop sewing a pattern combination and wish

to sew it over again, press the memory button to sew the

pattern combination from the beginning.

q Pattern combination

w Stop sewing.

e Press the memory button.

r Sews the pattern combination from the beginning.

If you have to stop sewing a pattern combination and wish

to sew from the incomplete pattern, press the mirror image

button to sew from the beginning of the pattern last sewn.

q Pattern combination

w Stop sewing.

e Press the mirror image button.

r Sews the pattern combination from the pattern last

sewn.

Programming French knots

Select pattern #48 (mode 2).

Press the memory button.

A knot and 2 counts of straight stitch is memorized.

Select pattern #38 (mode 2).

Press the memory button.

Three counts of straight stitch is memorized.

French knots will be sewn after every 5 counts of straight

stitch.

q Pattern #48 (French knot and 2 counts of straight stitch)

w Pattern #38 (3 counts of straight stitch)

Extender Stitches

Patterns #44, #45 and #50 (mode 2) are extender stitches

which are used to insert straight stitches between stitch

patterns.

The extender stitches inherit the stitch length and needle

drop position of a previous pattern in the programmed

pattern combination.

Example: Inserting 2 counts of the straight stitch between

the blind stitches (pattern #09, mode 2)

Select pattern #09 (mode 2).

Press the memory button.

Pattern #09 is memorized.

Select pattern #44 (mode 2).

Press the memory button.

Pattern #44 (2 counts of straight stitch) is memorized.

Two counts of straight stitch are inserted between blind

stitches.

q Pattern #09 (blind stitch)

w Pattern #44 (2 counts of straight stitch)

NOTE:

Pattern #46 is an extender stitch for the triple stretch stitch

(#05).

Example: Inserting 4 counts of the straight stitch after

pattern 56 (mode 2)

Program pattern #56 and #45 (4 counts of straight stitch).

q Pattern #56

w Pattern #45 (4 counts of straight stitch)

Other extender stitches

The stitch length and needle drop position of patterns #36,

#37, #38, #40, #41 and #42 are independent from those of

the combined pattern.

Example: Inserting 3 counts of the straight stitch after

pattern 32 (mode 2)

Program pattern #32 and #42 (3 counts of straight stitch).

q Pattern #32

w Pattern #42 (3 counts of straight stitch)

To insert blank space, use pattern #99.

Trim the connecting thread after sewing.

e Connecting thread

Programming Letters

Selecting a letter style

Press the letter style button to choose one of the following

letter styles:

q Block

w Block (European letters)

e Script

r Script (European letters)

t Broadway

y Broadway (European letters)

u Decorative patterns

Each time you press the letter style button, the letter style

will change in the order above.

NOTE:

The stitch patterns in mode 2 and 3 cannot be programmed

with letters.

Use the decorative patterns in the lettering mode to

program a combination of letters and decorative patterns.

Programming letters

Example: To program “R&B” in Block style

z Press the letter style button to select Block style.

Select the uppercase letter “R” (pattern 28).

x Press the memory button.

Uppercase letter “R” will be memorized.

c Select letter “&” (pattern 64).

v Press the stitch width “–” button to reduce the letter size.

b Press the memory button.

Small “&” will be memorized.

n Select uppercase letter “B” (pattern 12).

m Press the memory button.

Uppercase letter “B” will be memorized.

Viewing a long text

The LCD screen shows up to 8 characters at a time.

If the entire text is not displayed, press the edit button or

help button to scroll the text.

Pressing the edit button shifts the cursor and scrolls the

text to the left.

Pressing the help button shifts the cursor and scrolls the

text to the right.

NOTE:

Arrows under a character indicate that there are

remaining characters in that direction.

q Arrow

Programming letters and decorative patterns

Example: To program “I



You”.

Select the uppercase Block style.

Select “I” (pattern #19) and memorize it.

Select the decorative patterns.

Select “



” (pattern #01) and memorize it.

Select the Block style.

Memorize “Y”, “o” and “u”.

Editing the Programmed Patterns

Deleting a letter (pattern)

Example: To delete “C” from “ABCD”

Press the edit button to shift the cursor under letter “C”.

q Cursor

Press the clear button. Letter “C” is deleted.

NOTE:

Pressing and holding the clear button will delete all the

programmed patterns and the LCD screen will return to the

initial display of the selected mode.

Inserting a letter (pattern)

Example: To insert a blank space between “B” and “C” in

“ABCD”

Press the edit button to shift the cursor under letter “C”.

Select pattern 99 (blank space).

Press the memory button.

A space is inserted before letter “C”.

Duplicating a pattern (letter).

Example: To duplicate pattern #31of the pattern

combination

Press the edit button to shift the cursor under the pattern to

duplicate (#31).

Press the memory button.

Pattern #31 is duplicated.

Stitch adjustment of programmed patterns

The stitch width and length of the programmed stitch

patterns can be altered uniformly or individually.

Example: To alter the stitch width uniformly

Press the edit button to shift the cursor to the right of the

last programmed pattern.

Press the stitch width adjustment button to alter the stitch

width.

The stitch width of programmed patterns will be uniformly

altered.

NOTE:

Stitch length can also be uniformly altered when patterns

of the same category (satin stitches or stretch stitches)

have been programmed.

Example: To alter the stitch width individually

Press the edit button to shift the cursor under the pattern

you wish to alter.

Press the stitch width adjustment to alter the stitch width.

The stitch width of the desired pattern will be altered

individually.

NOTE:

To view the stitch setting of each pattern, shift the cursor

under the desired pattern then press the stitch width or

length adjustment button. The settings will be displayed on

the LCD screen.

Unified needle drop position

The needle drop position of the programmed patterns will

vary depending on the combination:

q Unified to the left when combining the patterns with

the left needle position and the center needle position.

w Unified to the right when combining the patterns with

the right needle position and the center needle position.

e Unified to the center when combining the patterns with

the left needle position and the right needle position.

r Unified to the center when combining the patterns with

the left, right and center needle positions.

Storing and Recalling the Pattern Combinations

A pattern combination can be stored in the memory for

future use even after turning the machine off.

The stored pattern combination can be recalled by pressing

the memory/call button.

You can store total 5 combinations in mode 2, mode 3 and

lettering mode.

NOTE:

Memory/call function is not available in mode 1.

Storing the pattern combinations

Program the desired pattern combination.

Press the memory/call button.

Press the memory button to store the stitch pattern

combination.

* The machine beeps and an hourglass appears on the

LCD screen while the machine is saving the stitch

pattern combination.

Do not turn the power switch off while the machine is

beeping or an hourglass is indicated on the LCD

screen.

* You can access other memory address (M2 to M5) by

pressing the memory/call button.

* To exit from the memory/call mode, press any key except

the memory, clear, turnover memory, edit or help button.

Overwriting a stored combination

Program the desired combination.

Press the memory/call button to select the desired memory

address.

The LCD screen will show the pattern combination already

stored.

Press the memory button and the stored combination will

be replaced with the new combination.

Recalling a stored combination

Select mode 2, 3 or lettering.

Press the memory/call button to select the desired memory

address.

Press the mirror image button to recall the stored

combination.

Deleting a stored combination

Press the memory/call button to select the desired memory

address.

Press and hold the clear button to delete the stored

combination.

Correcting Distorted Stitch Patterns

The sewing results of the stretch patterns may vary

depending upon the sewing conditions, such as sewing

speed, type of the fabric, number of layers etc.

Always test sew on a scrap piece of the fabric that you

wish to use.

If stretch patterns, letters or numbers are distorted, correct

it with the feed balancing dial.

q Feed balancing dial

Stretch stitch pattern

If the pattern is compressed, turn the feed balancing dial in

the direction of “+”.

If the pattern is drawn out, turn the feed balancing dial in

the direction of “–”.

Letters and numbers

If the pattern is compressed, turn the feed balancing dial in

the direction of “+”.

If the pattern is drawn out, turn the feed balancing dial in

the direction of “–”.

Stitch balance of buttonholes #19 and #21

(mode 2)

If the right row is denser, turn the feed balancing dial in the

direction of “+”.

If the left row is denser, turn the feed balancing dial in the

direction of “–”.

Evenness of bartacking

If the stitch does not meet start position, turn the feed

balancing dial in the direction of “+”.

If the stitch does not meet return position, turn the feed

balancing dial in the direction of “–”.

(+)

(–)

(+)

(–)

(+)

(–)

(+)

(–)

CARE AND MAINTENANCE

CAUTION:

Press button to open the sub needle plate and turn the

power switch off and unplug the machine before cleaning.

NOTE:

Do not dismantle the machine in any way other than what

is explained in this section.

Cleaning the Hook Race and Feed Dog

z Remove the needle and presser foot. Remove the

setscrew and remove the needle plate.

q Screwdriver

w Setscrew

e Needle plate

x Take out the bobbin. Lift up the bobbin holder and

remove it.

r Bobbin holder

c Clean the bobbin holder with a lint brush and soft dry

cloth.

t Lint brush

v Clean the feed dog and hook race with the lint brush.

y Feed dog

u Hook race

b Clean the hook race with a dry cloth. (You may also

use a vacuum cleaner.)

i Soft dry cloth

Inserting the bobbin holder

z Insert the bobbin holder.

x The knob of the bobbin holder should fit next to the

stopper on the hook race.

q Knob

w Stopper

c Reattach the needle plate and tighten the screws.

NOTE:

After cleaning the machine, attach the needle and presser

foot.

Replacing the Light Bulb

WARNING:

Turn the power off before replacing the light bulb.

The bulb could be HOT, wait until it has cooled down before

touching it.

To remove:

Open the face cover.

Pull out the bulb from the lamp socket.

To replace:

Insert a new bulb into the opening of the socket.

Close the face cover.

q Face cover

w Bulb

e Lamp socket

Replace the bulb with the same type, rated 12 V, 5 W.

Replacing the light bulb on the underside of the sewing

arm

z Lay the machine on its back.

x Remove the clear window with the screwdriver as shown.

q Clear window

c Pull out the lamp holder from the opening by hooking the

holder plate with your fingertip.

w Holder plate

v Pull out the light bulb from the lamp socket.

e Light bulb

r Lamp socket

b Insert a new bulb into the socket.

n Push the lamp holder back into the opening.

m Attach the window into the opening on the machine.

Replace the bulb with the same type, rated 12 V, 5 W.

Warning Messages

Message Problem/Cause

If a buzzer sounds and the LCD screen shows one of these messages, follow the guidance below.

• The machine will stop after several stitches if the

buttonhole is sewn without lowering the

buttonhole lever.

• The machine is started with the presser foot up.

• The machine will stop if the presser foot is raised

while sewing.

• The machine is stopped while sewing a locking

stitch.

• The twin needle button is pressed when a pattern

unsuitable for twin needle sewing has been

selected.

• An unsuitable pattern is selected when the twin

needle mode has been activated.

Lower the presser

foot and start the

machine again.

Lower the buttonhole

lever and start the

machine again.

Cancel the twin needle

mode, and sew with a

single needle.

Sew until it automatically

stops.

Remedy

• The machine is started soon after it has

halted due to overloading.

• Bobbin winder spindle locks during bobbin

winding.

Wait for at least 15

seconds to restart.

If thread jamming causes

overload, remove the

tangled threads.

Turn off the power and

remove tangled thread.

• The machine is turned on when the needle is in

the down position.

Press the up/down needle

position button to raise the

needle.

• The machine is turned on when the needle is in

the down position and the bobbin winder spindle

is shifted to the left.

Turn the hand wheel to

raise the needle.

• The elongation button is pressed when a pattern

that cannot be elongated has been selected.

• The memory button is pressed when a pattern that

cannot be programmed has been selected.

Select satin stitches to

be elongated.

Select the equivalent

patterns from mode 2.

• The LCD screen shows an abnormal display.

• Power switch is turned on while depressing

the foot control.

• The machine is malfunctioning due to a

problem in its electronic components.

The foot control is disconnected while sewing.

• The start/stop button is pressed after the foot

control has been connected.

Turn OFF the power and

connect the foot control.

Disconnect the foot control

and restart the machine.

Release the foot control.

Contact the service center or

the store from where the

machine was

purchased.

Turn the power switch

off and turn it on

again.

Audible Signals

BEEP Beep sounds during:

pip

pip-pip-pip

Normal operation

Invalid operation

Message Problem/Cause

Remedy

F1 ERROR

• The sub needle plate mechanism fails to

operate properly.

Raise the presser foot and turn

the power switch off.

Clean the hook area, then turn

the power on again.

It is normal that a faint humming sound is coming out from the internal motors.

1. The needle thread is not threaded properly.

2. The needle thread tension is too tight.

3. The needle is bent or blunt.

4. The needle is incorrectly inserted.

5. The needle thread and the bobbin thread are not set under the

presser foot when starting sewing.

6. The thread is either too heavy or too fine for the needle.

1. The bobbin thread is not threaded properly in the bobbin holder.

2. Lint has collected in the bobbin holder.

3. The bobbin is damaged and doesn't turn smoothly.

1. The needle is incorrectly inserted.

2. The needle clamp screw is loose.

3. The threads are not drawn to the rear after sewing.

4. The needle is too fine for the fabric being used.

1. The needle is bent, blunt or incorrectly inserted.

2. The needle and/or fabrics are not suitable for the work being

sewn.

4. The needle thread is not threaded properly.

5. A poor quality needle is being used.

1. The needle thread tension is too tight.

2. The needle thread is not threaded properly.

3. The needle is too heavy for the fabric being sewn.

4. The stitch length is too long for the fabric.

1. The feed dog is packed with lint.

2. The stitches are too fine.

3. The feed dog is not raised after "drop feed" sewing.

1. The needle thread tension is too loose.

2. The needle is either too heavy or too fine for the thread.

1. The machine is not plugged in.

2. Thread has been caught in the hook race.

3. The bobbin winder spindle is not returned to the left after bobbin

winding.

1. The stitch density is not suitable for the fabric being sewn.

2. A suitable interface material has not been used for stretch or

synthetic fabric.

1. Thread has been caught in the hook race.

2. Lint has built up in the hook race or bobbin holder.

Troubleshooting

Condition

The needle thread

breaks.

The bobbin thread

breaks.

The needle breaks.

Skipped stitches

Seam puckering

The cloth is not

feeding smoothly.

Stitches form loops

below the fabric.

The machine does not

work.

Buttonhole is not sewn

properly.

The machine does not

run smoothly and is

noisy.

Reference

Cause

See page 20

See page 24

See page 23

See page 26

See page 23

See page 19

See page 74

Replace bobbin.

See page 23

See page 26

See page 23

See page 20

Change the needle.

See page 24

See page 20

See page 23

Make the stitch coarser

See page 74

Make the stitch coarser.

See page 25

See page 24

See page 36

See page 5

See page 74

See page 18

See page 44

See page 41

See page 74

844-800-020 (E)

MIJN JANOME 5200 GEEFT IN DE DISPLAY AAN EROR 3 STAAT NIET IN BOEK WAT DIT BETEKEND, ALLES DOET HET BEHALVE NAAIEN Gesteld op 3-12-2020 om 10:02
Reageer op deze vraag Misbruik melden
Ik ben mijn stekentabel kwijt en dat is heel vervelend, kan ik deze opnieuw bij u bestellen?
Ik zou er heel erg mee geholpen zijn.
Zeg maar wat de kosten zijn zo dat ik ze over kan maken,
m v g Gerrie Hoekstra Gesteld op 20-10-2020 om 14:21
Reageer op deze vraag Misbruik melden
Spel dr uit gehaald stof eruit gehaald wiel werkt niet
Gesteld op 31-3-2020 om 12:58
Reageer op deze vraag Misbruik melden
Heb de spoel eruit gehaald schoon gemaakt maar Mn wiel draait niet
Gesteld op 31-3-2020 om 12:48
Reageer op deze vraag Misbruik melden
Ben aan het naaien maar ik trek de draad er zo weer uit

Gesteld op 20-10-2019 om 09:55
Reageer op deze vraag Misbruik melden
- Het wiel draait niet
  Geantwoord op 31-3-2020 om 12:57
  Waardeer dit antwoord (1) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Janome Memory Craft 5200 bij:

nieuwe vragen en antwoorden
nieuwe handleidingen

U ontvangt een email met instructies om u voor één of beide opties in te schrijven.

Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Janome Memory Craft 5200 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,93 mb groot.

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.

Janome Memory Craft 5200 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info

Janome Memory Craft 5200 Handleiding

Hulp nodig? Stel uw vraag in het forum

Forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info