555040
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
GSM car alarm CA-1802 „Athos“ 4/6 MHF57202
Factory default setting is SET 1001111101 (bold letters in the text).
If you want to change only particular DIP or SET parameters, enter x for the
others (i.e.
MASTER SET xx2xxxxxxx will set an extended locking signal for
closing the windows).
8. User instructions
8.1. Remote control arming and disarming
Button
is used to arm and lock the vehicle completely. Using the
button the car can be disarmed and unlocked. If you re-press the
button within 15 seconds after arming, partial arming occurs (confirmed
acoustically). In this mode, the internal wireless detectors are not active,
nor is the low voltage sensor. Also no voltage is supplied for external
sensors. Using the CR-11A module, pressing the buttons
and
together allows you to use additional functionality (e.g. switching
independent heating).
8.2. SMS control from an authorized phone
Text SMS Description
AM
ARM and lock the car
AM EXT
Partially ARM and lock the car
DM
DISARM and unlock the car
IMO
STOP (immobilize) the car (after turning ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
Car alarm will reply with status information, e.g. „car
reports: Time: 27.01.04 13:04, Status: Armed, Unblocked,
Ignition off“.
HELP
The car alarm will reply with a brief list of SMS instructions.
UC xxxx
To change the user code. xxxx is the new user code, 4 to 8
characters (A –Z & 0 – 9). Factory default user code is
USER
CREDIT
parameter
To obtain the balance of a prepaid SIM card if used. See
12.6-8 for details
AUX
parameter
To operate CR-11A output relays as well as the appliances
or circuits that are connected to these relays (see par. 13)
HF abcdef
Hands-free set adjustment:
a – enable calls (0= disabled, 1=enabled)
b – auto answer incoming calls (0= disabled, 1=enabled)
c – microphone sensitivity 0 to 9, (5)
d – speaker volume 0 to 9, (5)
e - ringing tone volume 0=mute to 9= max., (5)
f – ringing sound 0 to 9, (1)
SIREN
To activate the siren for 30 seconds
The instruction must contain spaces (e.g. HF 105551).
If an SMS instruction is sent from an unauthorized phone, it is
necessary to put a user code before the instruction (default is USER).
Again, a space is necessary. An example of arming from an
unauthorized phone: USER AM
SMS instructions are not case-sensitive. Only basic ASCII can be
used in the SMS instruction texts.
If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending an
SMS from an internet gateway which adds more text –
advertisements etc. When using the % character it is always
necessary to insert the Master or User code followed by a space
before the command itself.
SMS instructions can be renamed. Example: It is possible to replace
“AM“ by “LOCK“.
The parameters in bold are factory defaults.
8.3. Dialling-in remote control
Complete remote control by dialling-in from an authorized phone is
possible (see table DIP – parameter E). If you dial the car alarm number
from an authorized phone, it will cause a change of state (arming,
disarming, etc.). A call to the alarm is free of charge (the car alarm will not
answer the incoming call). If operated by dialling-in after an alarm has
been triggered, a slight delay can occur. If disarmed by dialling-in after
partial arming, then a subsequent dialling-in will cause complete arming.
Change of state after dialling-in can be confirmed via SMS (optional).
8.4. Phone calls by handsfree set (HF-03)
If the HF-03 hands free set is installed, it is possible to receive calls
and to dial pre-programmed phone numbers DIAL x. When the
ignition key is on, the remote control (RC-8x) allows you to operate
the hands free set. The call is done via the car alarm’s SIM, the
handsfree set is not usable for other phones.
Incoming calls – to answer them, press any button on the RC-8x
remote control. By pressing any button again, the call will be
terminated.
Calls can be automatically answered, see the HF instruction manual.
Outgoing calls – when the ignition key is on, the RC-8x allows you
to call up to 4 pre-programmed numbers (see chapter 5.1).
When armed, all incoming calls are automatically rejected. If the car
is immobilized or after an alarm has been triggered all calls are
automatically answered (it is possible to listen in).
8.5. Alarm
When an alarm is triggered, the siren will sound for 30 sec., warning
SMS messages will be sent to all phones (TEL1 to TEL4) and these
phones will also be called with the siren sound. If automatic location is
turned on, a request for location detection is sent. After the user stops the
alarm, all transmissions are terminated.
To stop the alarm, disarm the alarm by pressing the
button on
the remote control or by a disarm SMS instruction (DM). The DM
instruction unlocks the car at the same time. After the alarm has been
stopped by a user in a regular way, an SMS will be sent informing
about alarm termination.
Example of an alarm SMS:
Your car reports: Alarm, INP activation, Time 10.12.04 01:45
Mercedes reports: Alarm, FIRE, garage sensor activation, Time 11.02.04
01:12
8.6. Acoustic signalling of arming/disarming
If acoustic signalling is ON (see table 6), the arming is confirmed by
1 beep and disarming by 2 beeps. Partial arming is indicated by two
short beeps. Three beeps while disarming the car indicate that an
alarm was triggered during the armed state. If arming a car with an
active alarm input (e.g. open car boot) arming is supplemented by four
short beeps. The siren will also indicate triggering of a wireless
detector which provides an entrance delay (by a single beep).
9. Editing SMS texts
The SMS texts (alarm information and instructions) are factory pre-
programmed. However, it is possible to change these texts using a
mobile phone or via the www.GSMLink.cz
internet page. This makes
communication convenient for the user.
To change text by mobile phone, send an SMS as below. A single
SMS enables you to specify changes to several texts. Terminate each
text with a comma:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see following table)
text is your new text – up to 30 characters, full stop (dot)
or comma cannot be used in the text, spaces are
allowed
Example: MASTER TXT 01,LOCK PLEASE
Text numbers 01 to 26 are instructions requiring a MASTER code for
their modification. If you modify these texts, you change the
instructions which the car alarm will respond to. For example, replacing
“STATUS” with “STATE PASSWORD” will cause that state detection
will be obtainable by “STATE PASSWORD” only. This way you can
insert a “password” into the texts which prevents misuse. All other
texts are of informational character and correspond to particular
events, states and input names. This allows you to adjust the names to
a form which suits you well. For example, “INP 1” can be replaced with
“bonnet” etc. Texts can be replaced using the MASTER code as well
as the USER code (optional).
A convenient way for text modification is to use the GSMLink web
page, see paragraph 11.
SMS text table
zz Factory default text zz Factory default text
SMS commands: 48 Telephone 4
01 AM 49 Telephone UC
02 DM 50 Telephone – MC
03 IMO 51 Wireless detector 1
04 UNIMO 52 Wireless detector 2
05 STATUS 53 Wireless detector 3
06 HELP 54 Wireless detector 4
07 CREDIT 55 Wireless detector 5
08 DIAL 56 Wireless detector 6
09 HF 57 Wireless detector 7
10 LOCATOR 58 Wireless detector 8
11 MC 59 Wireless controller 1
12 UC 60 Wireless controller 2
13 DIP 61 Wireless controller 3
14 TEL 62 Wireless controller 4
15 LEARN Status information:
16 SIREN 64 Car alarm reports
17 SET 65 Status:
18 AUXA 66 Armed
19 AUXB 67 Disarmed
25 ON 68 Ignition key ON
26 OFF 69 Ignition key OFF
Events: 70 Engine is blocked
30 Alarm 71 Engine is unblocked
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-1802 - Athos GSM RESET 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-1802 - Athos GSM RESET 1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Jablotron CA-1802 - Athos GSM RESET 1

Jablotron CA-1802 - Athos GSM RESET 1 Gebruiksaanwijzing - English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info