533227
11
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
EN
11
OFF
(
CHARGE
)
PLAY
w
$
t y
r
180°
90°
o
20
5
m
h
1h30m
1h29m
0h03m
1h30m
0h02m (Blinking)
0h01m (Blinking)
0h00m (Blinking)
( )
Now
calculating
During shooting
Basic Recording
Perform the procedures listed below before continuing.
Power ( pg. 7)
Grip Adjustment ( pg. 8)
Viewfinder Adjustment (
pg. 8)
Load A Cassette (
pg. 9)
Recording Mode Setting ( pg. 10)
1 Remove the lens cap.
Pull on bottom end o of LCD monitor to open.
2 Set the Power Switch y to “ or ” while
pressing down the Lock Button
t located on the
switch.
Shooting while using the LCD monitor: Open the
LCD monitor fully.
Shooting while using the viewfinder: Pull out the
viewfinder fully.
The POWER/CHARGE lamp r lights and the
camcorder enters the Record-Standby mode. “PAUSE”
^ is displayed.
The image will not appear simultaneously on the LCD
monitor and the viewfinder. See “PRIORITY” in the
SYSTEM Menu ( pg. 23).
3 Press the Recording Start/Stop Button w. “
%, ^ appears and the tally lamp 3 lights while
recording is in progress.
To Stop Recording, press the Recording Start/Stop
Button w. The camcorder re-enters the Record-
Standby mode.
To Adjust The Brightness Of The Display
1. Make sure the Power Switch y is set to ” and
open the LCD monitor fully, then press the MENU/
VOLUME wheel $ in. The Menu Screen appears.
2. Rotate the MENU/VOLUME wheel $ to select
(CAMERA DISPLAY)” and press it.
3. Rotate the MENU/VOLUME wheel $ to select
“BRIGHT” and press it. The Menu Screen closes and
the bright level indicator 7 appears on the display.
To cancel, press the MENU/VOLUME wheel $
again so that the bright level indicator 7 disap-
pears.
4. Rotate the MENU/VOLUME wheel $ until the bright
level indicator 7 moves and the appropriate
brightness is reached, then press it. The bright level
indicator 7 disappears.
It is also possible to adjust the brightness of the
viewfinder by closing the LCD monitor, pulling out
the viewfinder and adjusting as described above.
TAPE RECORDING
NOTES:
If the Record-Standby mode continues for 5 minutes, the
camcorder’s power shuts off automatically. To turn the
camcorder on again, push back and pull out the
viewfinder again or close and re-open the LCD monitor.
When a blank portion is left between recorded scenes on
the tape, the time code is interrupted and errors may
occur when editing the tape. To avoid this, refer to
“RECORDING FROM THE MIDDLE OF A TAPE”
(
pg. 13).
To turn the tally lamp
3 or beep sounds off,
pg. 23.
When you use the LCD monitor outdoors in direct
sunlight, the LCD monitor may be difficult to see. If this
happens, use the viewfinder instead.
Black spots or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor or the
viewfinder (
pg. 35).
When the Recording Start/Stop button
w is pressed, it
may take a few seconds before actual recording starts.
% starts rotating when the camcorder actually
starts recording.
The time required to calculate and display the remaining
tape length, and the accuracy of the calculation, may vary
according to the type of tape used.
“TAPE END” appears when the tape reaches its end, and
the power goes off automatically if left in this condition for
5 minutes. “TAPE END” also appears when a cassette at
its end is loaded.
Tape remaining time
indicator (Approximate)
Display
01 D50/40/30/20EK 11-15 02.12.4, 19:0911
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JVC GR-D40 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JVC GR-D40 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van JVC GR-D40

JVC GR-D40 Gebruiksaanwijzing - Nederlands - 48 pagina's

JVC GR-D40 Gebruiksaanwijzing - Deutsch - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info