756980
7
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
ENGLISH USER MANUAL
JB SYSTEMS® 5/12 EZ-CON 192
32. [DMX OUTPUT]: Sends DMX-signals to the connected fixtures
33. [M-DMX OUTPUT]: Please note that this USB-connector is NOT used for updates or to connect the
unit to a PC! Instead this USB-connector makes it very easy to add wireless DMX to the unit! Just
add the (optional) WTR-DMX DONGLE from BRITEQ® and you will get wireless DMX! No extra
settings to be made in the setup menu, just follow the procedure in the user manual supplied with
the WTR-DMX DONGLE from BRITEQ®. The separate WTR-DMX DONGLE is available from
WWW.BRITEQ-LIGHTING.COM (order code: B04645)
34. USB A-PORT: Used to insert a memory stick for recording the programmed shows. Can also be
used to put in a USB LED light (5V)
35. POWER SWITCH: Used to switch the unit ON/OFF
36. MAINS INPUT: with IEC14 socket and integrated fuse holder, connect the supplied mains cable
here.
SET UP
1. [FIXTURE SETUP]: The EZ-CON 192 has 12 [FIXTURES] (1) buttons”. Each fixture button
represents 16 DMX channels. (8 faders on page A and 8 faders on page B)
The following chart helps you to set up the DMX-start address on your fixtures:
Digital Setting
Dip Switch Setting
1
1 “On”
17
1 and 5 “On”
33
1 and 6 “On”
49
1,5 and 6 “On
65
1 and 7 “On”
81
1,5 and 7 “On”
97
1,6 and 7 “On”
113
1,5,6 and 7 “On”
129
1 and 8 “On”
145
1,5 and 8 “On”
161
1,6 and 8 “On”
177
1,5,6 and 8 “On”
2. [JOGWHEEL SETUP]: For each fixture any 2 addresses can be assigned to the PAN (19) and TILT
(18) jogwheels:
Press and hold the [PROGRAM] (25) button until its LED blinks.
Press 2 times the [MODE] (21) and [FINE] (20) buttons at the same time. The assign LED (10)
should light up. (if reverse LED (22) is lit, press both buttons a second time together)
Use the [BANK ] (14) and [BANK ] (14) buttons to select the axis you wish to assign (PAN or
TILT).
If your fixture has more than 8 DMX addresses, you can use the [TAP/DISPLAY] (16) button to
select 16 or 8 channel mode.
Press the button (1) corresponding to the fixture you wish to edit.
While holding the [MODE] (21) button press the scene number (6) corresponding to the fader
which controls the movement. (Example: If PAN is controlled by fader number 4, press and hold
the [MODE] (21) button while pressing scene (6) button 4).
When both PAN and TILT are assigned, press the [MODE] (21) and [FINE] (20) buttons at the
same time again to exit ASSIGN mode.
Note: you can still use the channel faders instead of the jog wheels to control the movements of the
fixture.
1. DELETE JOGWHEEL SETUP FOR A FIXTURE:
Enable Programming Mode. (Press and hold the [PROGRAM] (25) button until its LED blinks)
Press 2 times the [MODE] (21) and [FINE] (20) buttons at the same time. The ASSIGN LED (10)
should light up. (if the REVERSE LED (22) is lit, press both buttons a second time together)
If your fixture has more than 8 DMX addresses, you can use the [TAP/DISPLAY] (16) button to
select 16 or 8 channel mode.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JB systems EZ-CON 192 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JB systems EZ-CON 192 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van JB systems EZ-CON 192

JB systems EZ-CON 192 Gebruiksaanwijzing - Nederlands - 20 pagina's

JB systems EZ-CON 192 Gebruiksaanwijzing - Deutsch - 20 pagina's

JB systems EZ-CON 192 Gebruiksaanwijzing - Français - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info