578941
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
RESETTING TEMPERATURE MEMORIES
Select the TEMPERATURE/HUMIDITY window.
Press and hold the MEM button for 3 seconds to clear all max/min memories.
COMFORT LEVEL INDICATION
The main unit is capable of detecting and displaying the current indoor comfort levels of
the room climate. The comfort level is based on the combination of the current indoor
temperature and humidity reading. The following comfort levels may be displayed:
COMFORT (comfortable); WET (wet) and DRY (dry)
Indicator
displayed
COM
WET
DRY
Temperature
Range
Humidity
Range
Shows current
condition
20°C to 25°C
(68°F to 77°F)
40%RH-
70%RH
Ideal relative humidity
and temperature
-5°C to 50°C
(23°F to122°F)
OVER
70%RH
Contains excess
moisture
5°C to 50°C
(23°F to122°F)
BELOW
40%RH
Contains inadequate
moisture
Note: If there is no comfort indication, this means that it is not wet and not dry, but
the temperature is higher or lower than the indicated comfort level.
4.3 CLOCK WINDOW
For all operations described in Chapter 4.5, press UP () or DOWN () until the
TIME icon, in the left corner of the time window, begins to flash.
4.3.1 TIME FUNCTION
The radio controlled time signal (DCF 77) is transmitted from the central atomic clock in
Frankfurt/Main. It has a reception range of approx. 1500 km. If the tower icon is not fully
lit, or if the time and date are not set automatically, please consider the following:
During night-time hours, atmospheric disturbances are typically less severe and radio
signal reception may improve. A single daily reception is sufficient enough to keep the
clock accuracy within 1 second.
Make sure the unit is positioned at least 2 meters (8 feet) distance from any interference
source such as a TV, computer monitor, microwave, etc.
Within concrete and /or metal wall rooms, such as basements or office buildings, the
signal may be weakened. In such a case, place the main unit near the window for better
reception. Sometimes it also helps to turn the unit by 90°
NOTE: In any of below described settings, the unit will automatically exit any
programming mode if it does not detect a button press for about 2 minutes. Any setting
made before this will not be taken over by the unit. Therefore, as long you are in a setting
and you have made changes, close the setting mode as described in below chapters.
HOW TO SET THE RADIO CONTROLLED CLOCK
1. After the batteries are installed. The clock will search the radio signal automatically
(DCF77 from Germany). It takes about 3-10 minutes to finish this process.
2. If you wish to disable the auto-reception feature, hold UP () for 3 seconds to disable
it. Having done that, the tower icon will disappear.
3. To enable the auto-reception feature again, hold UP () for 3 seconds again to start the
reception and the regular synchronization (daily at 0:00, 3:00, 6:00 and 12:00).
ICON Time Signal Reception Strength
Undefined data(Flashing)
No Reception for the past 24 hours
Weak signal, but can be decoded
Strong signal
4. If the radio signal is received, the date & time will be set automatically and the radio
control signal icon [ ] turns on.
5. If the clock fails to receive the time signal, it will show the [ ] icon. If the time is not
correct, you may set the time manually.
HOW TO SET THE CLOCK MANUALLY
To set the clock manually, make sure the display shows the time (not the ZONE) and then
press and hold MODE.
Now it will show the language. You may choose among English (En), German (DE),
French (Fr), Italian (IT), Spanish (SP), Dutch (Du) and Swedish (SW). Press UP () or
DOWN () to change it.
Press MODE to confirm. Repeat the same procedure to set the year, month, day,
day-month format, 12/24 hour format, hour and minute. During the setting, press and hold
will change the value rapidly.
If there is an item you do not wish to change, simply press MODE to bypass the item.
After the last setting, pressing MODE will exit the setting mode and return to the clock
mode.
HOW TO SET THE TIME ZONE
To set the time zone, make sure the display shows the time with the ZONE icon. Then
press and hold MODE.
Press UP () or DOWN () to adjust value in steps of 30 min. Press and hold either
button for fast advance. Press MODE to confirm your selection.
SELECT THE CLOCK/CALENDAR DISPLAY
Each time you press MODE, you may rotate from one of the following dispalys to the
next:
- Hour: Minute: Second
- Hour: Minute: Weekday
- Hour: Minute: Weekday of the Time Zone
- Hour: Minute: Second of the Time Zone
- Day: Month
4.3.2 WAKE-UP ALARM FUNCTION
There are three time alarms available on the main unit:
* Weekday Alarm
The alarm sound will be activated and the icon will flash on weekdays (Mo-Fr) when it
is armed and the alarm time is reached.
* Single Alarm
The alarm sound will be activated and the icon will flash when it is armed and the alarm
time is reached. Once it finished, it will be disabled automatically
* Pre-Alarm
The pre-alarm will be activated and the icon will flash if the temperature of channel 1 is
falling to +0 ºC or below.
It is programmable 15, 30, 45, 60 or 90 minutes earlier than the weekday alarm or single
alarm time.
ACTIVATING / DEACTIVATING THE TIME ALARMS
1. Press ALARM to rotate between:
- Weekday Alarm Time (displays OFF if weekday alarm deactivated)
- Single Alarm Time (displays OFF if single alarm deactivated)
- Pre-Alarm Time (displays OFF if pre-alarm deactivated)
2. When the above alarms are displayed, pressing UP () will activate, pressing
DOWN () will deactivate the corresponding alarm.
Note: Press MODE anytime during above alarm selection mode to return to normal clock
display.
SETTING THE TIME ALARMS
1. Press ALARM to select the alarm which you wish to configure.
2. Press and hold ALARM/ until hour starts flashing in the display
3. Set Alarm Hour:
Press UP () or DOWN () to adjust. Press and hold either button for fast changes.
Press ALARM to confirm your selection.
4. Set Alarm Minutes:
Press UP () or DOWN () to adjust. Press and hold either button for fast changes.
Press ALARM to confirm your selection
5. Upon completion the display will be returned to the alarm selection screen.
Note: Pre-alarm cannot be activated if weekday alarm or single alarm is not enabled.
STOP THE ALARM SOUND
The alarm will sound for 2 minutes with increasing intensity.
To stop it, press ALARM during the Alarm Sound to disable the alarm.
Note: For weekday alarm, pressing ALARM will only disable the alarm for the current
day. The alarm will be activated again the next day (if it falls within Monday to Friday).
If the Alarm is not interrupted by pressing the ALARM key, it will repeat itself after 8
minutes for 3 times.
Issue
Main unit
Radio Controlled
Time signal is not
received
Cannot locate
remote sensor
Place unit by the window and keep it there
overnight
Check batteries
Check location
Press and hold DOWN ( ) button on the
main unit to search for the signal form the
remote sensor
Remote sensor
Symptom Solution
6. BATTERY CHANGE
: BATTERY CHANGE DISPLAY
The batteries last for around 8-12 months. Depending on the usage of the unit and the
batteries used, this time can be slightly shorter or longer. In order to avoid a surprising
and unpleasant interruption to operations, a battery symbol may appear
- in the temperature window with the corresponding channel.
This means that batteries of the displayed sensor are becoming weak and need to be
replaced.
- in the time window
This means that batteries of the main unit are becoming weak and need to be replaced.
To change the batteries, please also consult Chapter 3 (Putting into operation).
Important:
- Insert batteries in the correct polarity
- Use only new batteries and never mix old and new batteries.
Please also remember that used batteries should not be thrown in the household rubbish
bin but handed in at the designated collection points. The environment will thank you for
it!
7. CARE INSTRUCTIONS
- Do not expose the device to extreme temperatures or direct sunlight over longer periods.
- Avoid blows and shocks of any kind to the device.
- For cleaning use a dry soft cloth that you have moistened with water and a mild cleaning
agent. Never use volatile substances such as benzene, thinner, cleansing agents in spray
cans etc.
- When the device is not being used store it in a dry area and out of the reach of small
children.
- If the device is activated under extreme coldness it may occur that the display becomes
illegible. As soon as it is returned to a warm environment the device will function
normally.
- Please keep the users manual and other documents delivered with the device stored
carefully so that you can reference them at a later point if necessary.
- Please use only new batteries and never mix old and new batteries.
- Please also remember that old batteries should not be disposed of with household waste
but should be handed in at the designated collection centres.
- Important: With all Irox appliances, all disposal fees in Switzerland (vRG; advance
recycling fee) and in the EU (WEEE) have been paid.
5. TROUBLESHOOTING
In case of a malfunction, always check the batteries and replace them in the main unit
and in the sensor(s) with new ones.
Please also check below issues before contacting customer service.
4746
4948
5150
5352
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Irox HBR636 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Irox HBR636 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Irox HBR636

Irox HBR636 Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info