686006
18
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
120A
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
OWNER’S MANUAL
IMPORTANT
SAFETY RULES
Please read, understand, and follow
all instructions carefully before
installing and using this product.
keep for future reference.
Don’t forget to try these other fine Intex products: Pools, Pool
Accessories, Inflatable Pools and In-Home Toys, Airbeds and
Boats available at fine retailers or visit our website listed below.
Due to a policy of continuous product improvement, Intex
reserves the right to change specifications and appearance,
which may result in updates to the instruction manual without
notice.
For illustrative purposes only. Accessories may not be provided with pool.
GRAPHITE GRAY PANEL POOL SET
TM
15’8” (478 cm) & 18’8” (569 cm) models
©2016 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/
Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801
Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/
Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
120-*A*-R0-1705
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 2
Warnings
/ Important safety rules
.................................................
3-4
Parts References
.............................................................................
5-6
Setup Instructions
...........................................................................
7-15
Pool Maintenance and Chemicals
.................................................
16-17
Common Pool Problems
................................................................
16
Pool Draining
...................................................................................
17
Storage
.............................................................................................
17-18
General Aquatic Safety
...................................................................
18
Limited Warranty
............................................................................
19
Special Introductory note:
Thanks for buying an Intex pool and enclosure. Please read this manual before setting up
your pool and enclosure. This information will help extend the pool life and make the pool safer
for your family's enjoyment. View the video included before installation. A team of 2-3 people is
recommended for pool and enclosure set up. Additional people will speed up the installation.
No tools are required for the assembly.
TABLE OF CONTENTS
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 3
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
Continuous and competent adult supervision of children and the disabled is required at all times.
Secure all doors, windows and safety barriers to prevent unauthorized, unintentional or unsupervised pool
entry.
Install a safety barrier that will eliminate access to the pool for young children and pets.
Pool and pool accessories are to be assembled and disassembled by adults only.
Never dive, jump or slide into an above-ground pool or any shallow body of water.
Failure to set up pool on flat, level, compact ground or over filling could result in the pool’s collapse and the
possibility that a person lounging in the pool could be swept out/ejected.
Do not lean, straddle, or exert pressure on the inflatable ring or top rim as injury or flooding could occur. Do
not allow anyone to sit on, climb, or straddle the sides of the pool.
Remove all toys and flotation devices from, in, and around the pool when it is not in use. Objects in the pool
attract young children.
Keep toys, chairs, tables, or any objects that a child could climb on at least four feet (1.22 meters) away
from the pool.
Keep rescue equipment by the pool and clearly post emergency numbers at the phone closest to the pool.
Examples of rescue equipment: coast guard approved ring buoy with attached rope, strong rigid pole not
less than twelve feet (12') [3.66m] long.
Never swim alone or allow others to swim alone.
Keep your pool clean and clear. The pool floor must be visible at all times from the outside barrier of the
pool.
If swimming at night use properly installed artificial lighting to illuminate all safety signs, ladders, pool floor
and walkways.
Stay away from the pool when using alcohol or drugs/medication.
Keep children away from pool covers to avoid entanglement, drowning, or other serious injury.
Pool covers must be completely removed before pool use. Children and adults cannot be seen under a pool
cover.
Do not cover the pool while you or anyone else is in the pool.
Keep the pool and pool area clean and clear to avoid slips and falls and objects that may cause injury.
Protect all pool occupants from recreational water illnesses by keeping the pool water sanitized. Don’t
swallow the pool water. Practice good hygiene.
All pools are subject to wear and deterioration. Certain types of excessive or accelerated deterioration can
lead to an operation failure, and can ultimately cause the loss of large quantities of water from your pool.
Therefore, it is very important that you properly maintain your pool on a regular basis.
This pool is for outdoor use only.
Empty pool completely when not in use for a longer period and safely store the empty pool in such a way
that it does not collect water from rain or any other source, and to prevent from being blown away by strong
wind. See storage instructions.
While the swimming pool is in use, you will need to operate the filter pump to ensure that there is at least
one complete change of water a day. Consult your pump’s manual to calculate the necessary
operating hours.
POOL BARRIERS AND COVERS ARE NOT SUBSTITUTES FOR CONTINUOUS AND COMPETENT
ADULT SUPERVISION. POOL DOES NOT COME WITH A LIFEGUARD. ADULTS ARE THEREFORE
REQUIRED TO ACT AS LIFEGUARDS OR WATER WATCHERS AND PROTECT THE LIVES OF ALL
POOL USERS, ESPECIALLY CHILDREN, IN AND AROUND THE POOL.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY OR DEATH.
Advisory:
Pool owners may need to comply with local or state laws relating to childproof fencing, safety barriers, lighting,
and other safety requirements. Customers should contact their local building code enforcement office for
further details.
WARNING
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 4
IMPORTANT SAFETY RULES
Please read, understand, and follow all instructions carefully before installing and using this product. These
warnings, instructions, and safety guidelines address some common risks of water recreation, but they cannot
cover all risks and dangers in all cases. Always use caution, common sense, and good judgment when
enjoying any water activity. Keep for future reference. Packaging must be read carefully and kept for future
reference. See product for additional warnings.
General
Check pins, bolts and screws for rust; splinters or any sharp edges regularly, especially accessible surfaces,
to avoid injuries.
Non swimmers safety
Continuous, active, and vigilant supervision of weak swimmers and non-swimmers by a competent adult is
required at all times (remembering that children under five are at the highest risk of drowning).
Designate a competent adult to supervise the pool each time it is being used.
Weak swimmers or non-swimmers should wear personal protection equipment when using the pool.
When the pool is not in use, or unsupervised, remove all toys from the swimming pool and its surrounding to
avoid attracting children to the pool.
Safety devices
It is recommended to install a barrier (and secure all doors and windows, where applicable) to prevent
unauthorized access to the swimming pool.
Barriers, pool covers, pool alarms, or similar safety devices are helpful aids, but they are not substitutes for
continuous and competent adult supervision.
Safety equipment
It is recommended to keep rescue equipment (e.g. a ring buoy) by the pool.
Keep a working phone and a list of emergency phone numbers near the pool.
Safe use of the pool
Encourage all users especially children to learn how to swim
Learn Basic Life Support (Cardiopulmonary Resuscitation - CPR) and refresh this knowledge regularly. This
can make a life-saving difference in the event of an emergency.
Instruct all pool users, including children, what to do in case of an emergency
Never dive into any shallow body of water. This can lead to serious injury or death.
Do not use the swimming pool when using alcohol or medication that may impair your ability to safely use
the pool.
When pool covers are used, remove them completely from the water surface before entering the pool.
Protect pool occupants from water related illnesses by keeping the pool water treated and practicing good
hygiene. Consult the water treatment guidelines in the user’s manual.
Store chemicals (e.g. water treatment, cleaning or disinfection products) out of the reach of children.
Removable ladders shall be placed on a horizontal surface.
Observe and follow the warnings and safety signs on the pool wall.
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 5
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
16'8'' (508 cm) model
NOTE:
Drawings for illustration purpose only. Actual product may vary. Not to scale.
26
12
13
14
15
16
17
18
19
22
20
21
23
24
25
1
2
3
4
5
6
7
8
9
10 11
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 6
REF. NO. DESCRIPTION
POOL SIZE & QUANTITIES
15'8" x 49"
(478 cm x124 cm)
18'8" x 53"
(569 cm x 135 cm)
1
PIN (WITH 2 EXTRA)
32
38
2
SEAL (WITH 2 EXTRA)
32
38
3
T - JOINT
15
18
4
SPRING PIN
15
18
5
VERTICAL LEG (SPRING PIN INCLUDED)
15
18
6
LEG CAP
15
18
7
HORIZONTAL BEAM
15
18
8
POOL LINER (DRAIN VALVE CAP INCLUDED)
1
1
9
DRAIN CONNECTOR
1
1
10
DRAIN VALVE CAP
1
1
11
GROUND CLOTH
1
1
12
WATERPROOF CAP (WITH 4 EXTRA)
34
40
13
BOLT (WITH 4 EXTRA)
34
40
14
TOP CLAMP COVER
15
18
15
TOP BOARD
15
18
16
TOP CLAMP
15
18
17
SUPPORT POST
15
18
18
PLUNGER VALVE CONNECTOR
2
2
19
STRAINER VALVE CAP
2
2
20
SIDE BOARD A
116
141
21
SIDE BOARD B
0
17
22
SIDE BOARD COMBINATION WITH TWO HOLES
1
1
23
SIDE BOARD COMBINATION WITH ONE HOLE
1
1
24
BOTTOM RAIL
15
18
25
BOTTOM CAP
15
18
26
BOLT WRENCH
2
2
REF. NO. DESCRIPTION
15'8" x 49"
(478 cm x124 cm)
18'8" x 53"
(569 cm x 135 cm)
SPARE PART NO.
1
PIN (WITH 2 EXTRA)
10312
10312
2
SEAL (WITH 2 EXTRA)
10648
10648
3
T - JOINT
10861
10862
4
SPRING PIN
10313
10313
5
VERTICAL LEG (SPRING PIN INCLUDED)
10864
10865
6
LEG CAP
10309
10309
7
HORIZONTAL BEAM
10414
10414
8
POOL LINER (DRAIN VALVE CAP INCLUDED)
11490
11110
9
DRAIN CONNECTOR
10201
10201
10
DRAIN VALVE CAP
11044
11044
11
GROUND CLOTH
18927
11290
12
WATERPROOF CAP (WITH 4 EXTRA)
12172
12172
13
BOLT (WITH 4 EXTRA)
12173
12173
14
TOP CLAMP COVER
12174
12174
15
TOP BOARD
12199
12199
16
TOP CLAMP
12200
12200
17
SUPPORT POST
12201
12202
18
PLUNGER VALVE CONNECTOR
11040
11040
19
STRAINER VALVE CAP
11240
11240
20
SIDE BOARD A
12203
12203
21
SIDE BOARD B
12204
12204
22
SIDE BOARD COMBINATION WITH TWO HOLES
12205
12205
23
SIDE BOARD COMBINATION WITH ONE HOLE
12206
12207
24
BOTTOM RAIL
12208
12208
25
BOTTOM CAP
12218
12218
26
BOLT WRENCH
11053
11053
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 7
POOL SETUP
WARNING
IMPORTANT SITE SELECTION AND GROUND
PREPARATION INFORMATION
• Thepoollocationmustallowyoutosecurealldoors,windows,andsafetybarrierstoprevent
unauthorized, unintentional or unsupervised pool entry.
• Installasafetybarrierthatwilleliminateaccesstothepoolforyoungchildrenandpets.
• Failuretosetupthepoolonflat,level,compactgroundandtoassembleandfillwithwater
in accordance with the following instructions could result in the pool’s collapse or the
possibility that a person lounging in the pool could be swept out/ejected, resulting in serious
injury or property damage.
• Riskofelectricshock:connectthefilterpumponlytoagroundingtypereceptacleprotected
by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). To reduce the risk
of an electrical shock, do not use extension cords, timers, plug adapters or converter plugs
to connect the pump to an electrical supply. Always provide a properly located outlet. Locate
the cord where it cannot be damaged by lawn mowers, hedge trimmers, and other equipment.
See the filter pump manual for additional warnings and instructions.
• Riskofseriousinjury:donotattempttoassemblepoolinhighwindconditions.
Select an outdoor location for the pool with the following requirements in mind:
1.
The area where the pool is to be set up must be
absolutely flat and level
.
Do not
set up the pool on a
slope or inclined surface.
2.
The ground surface must be compacted and firm enough to withstand the pressure and weight of a fully
set up pool.
Do not
set up the pool on mud, sand, soft or loose soil conditions.
3.
Do not
set up the pool on a deck, balcony or platform, which may collapse under the weight of the filled
pool.
4.
The pool requires at least 4 feet of space all around pool from objects that a child could climb on to gain
access to the pool.
5.
Grass under the pool will be damaged. Splash out chlorinated pool water could damage the surrounding
vegetation.
6.
Eliminate all aggressive grasses first. Certain types of grass such as St. Augustine and Bermuda, may
grow through the liner. Grass growing through the liner it is not a manufacture defect and is not covered
under warranty.
7.
The area shall facilitate drainage of the pool water after each use and/or for long term pool storage.
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 8
Unacceptable
Grade
Acceptable
Grade
Do not add
RemoveRemove
A
A
B
Always remove material from the top of the
slope rather than filling in the bottom.
2.1
GROUND PREPARATION
Select an outdoor location for the pool which should be on a level concrete pad. If there is no concrete pad
available, follow the instructions below to prepare the installation area. It is important you ask a professional
(builder or gardener) to perform the following ground preparation.
NOTE:
Tools are not included.
1.
Mark the installation area
Once the location area is chosen, drive stake at
center point of where you wish pool to be located.
Attach string to center stake. Measure the length
A on string, and attach marking stick, paint marker,
or funnel with flour to string. Mark circumference of
pool area using string and marker (see drawing 1.1).
For 15'8" (478 cm) pool, where
A = 8’3” (251.5 cm) = Radius of grass area need to
be removed and leveled.
For 16'8" (508 cm) pool, where
A = 8'9” (266.7 cm) = Radius of grass area need to
be removed and leveled.
For 18’8" (569 cm) pool, A = 9'9" (297.1 cm)
see drawing 1.2.
2. Clear the installation area
Remove all grass, stones and sticks from marked area. Also remove center stake and string.
3. Leveling
Establish lowest point in pool area. Level entire pool site by digging or scraping away uneven areas
to the level of the lowest point.
Always remove material from the top of the slope rather than
filling in the bottom
to ensure greater ground stability and firmness. When all the areas are level and
when excess ground is removed, you may fill any
small low areas
which are left to level (with fined
dirt). Always compact and level ground afterwards (see drawing 2.1).
POOL SETUP (continued)
1.1
A
A
B
1.2
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 9
Use a large mason rule (aluminum or wood)
and a level. Level out the ground by cutting
rectangles (or squares), locating this rule in
the selected and cleaned area (see
drawing 2.2).
4. Finishing
On the cleaned and leveled ground, spread a light coat of sieved dirt to a maximum depth of 1/2 inch
(1 cm). Spray water and compact it (with a garden roller). Double check and ensure it is well leveled.
The ground has to be perfectly level in order to proceed further.
5. Patio block installation
Purchase 15 pieces of patio block for 15’8” pool or 16 pieces of patio block for 16’8” pool or 18 pieces
for 18’8” pool. The minimum dimensions of each block should be 18” x 18” x 2”. Mark the area where
the blocks will be buried (see drawing 3.1), then remove 2” (5.08 cm) of soil from the marked area (see
drawing 3.2).
For 15’8” (478 cm) pool, where
A = 8’3” (251.5 cm) = Radius of grass area need to be removed and leveled.
B = 3’5” (104.1 cm) = Distance between each Patio Block.
For 16’8” (508 cm) pool, where
A = 8’9” (266.7 cm) = Radius of grass area need to be removed and leveled.
B = 3’5” (104.1 cm) = Distance between each Patio Block.
For 18’8” (569 cm) pool, where
A = 9’9” (297.1 cm)
B = 3’5” (104.1 cm)
The top of blocks should be flush with soil surface and level with the area surface and with all patio
blocks around entire pool (see drawing 3.3).
POOL SETUP (continued)
2.2
A
A
B
3.1
3.2
18” (45.7 cm)
18” (45.7 cm)
2” (5.08 cm)
3.3
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 10
POOL SETUP (continued)
You may have purchased this pool with the Intex Krystal Clear™ filter pump. The pump has its
own separate set of installation instructions. First assemble your pool unit and then set up the
filter pump.
Estimated assembly time 120 minutes. (Note the assembly time is only approximate and
individual assembly experience may vary.)
1. Liner preparation
Open the carton containing the liner, joints, legs, etc., very carefully as this carton can be used to store
the pool during the winter months or when not in use.
Take out the ground cloth
(11)
and spread it over the
cleared area. Then take out the liner
(8)
and spread it out
over the ground cloth, with the drain valve directed towards
the draining area. Place the drain valve away from the
house. Allow the sun to warm up the liner before inserting
the beams
(7)
into the sleeve openings.
IMPORTANT: Always set up the pool unit with at least 2
persons. Do not drag the liner across the ground as this
can cause liner damage and pool leakage (see drawing 4).
During the set-up of the pool liner, point the hose connections or openings in the direction of the electric
power source. The outer edge of the pool should be within reach of the pump’s electrical connection.
2. Frame assembly
The frame pool’s legs
(5)
and beams
(7)
fall into two groups. The larger diameters are the horizontal
beams that are slid (pushed) into the sleeve openings at the top of the liner. The smaller diameters are
the vertical legs. Both these legs and beams fit into the T-joints
(3)
.
Starting at any location, but always working in the same direction, push
the horizontal beam into the sleeve. Once the beam is centered take one
of the T- joints and using the connection pin
(1)
, attach the joint to one
end of the beam by inserting the pin through the seal
(2)
and in the
pre-drilled holes. Repeat this procedure in a circular fashion until all the
beams and joints have been connected
(see drawing 5.1)
.
The last joint connection may be difficult to complete. You can do
it though, if you first simultaneously raisethe last joint and beam
about 2 inches (5 cm). Now, insert the beam into the joint while
lowering the pieces into position. The beam will easily slide into
the joint (see drawing 5.2). Ensure that the last joint is fully
connected before proceeding to connecting the legs.
8
4
1
2
7
3
5.1
5.2
3
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 11
POOL SETUP (continued)
Next slide the vertical legs into the belt loop located in the middle of
the pool liner. Carefully slide the leg into the belt loop and insert the
top of the leg into the bottom of the joint.
Snap the leg into the joint’s holes by aligning the holes and the
spring-loaded pin. Attach the leg’s end cap
(6)
to the bottom of the
leg
(see drawings 6.1 & 6.2)
.
Upon connecting the last leg, grab hold of the frame pool’s top beams
in 2 – 3 locations. Shake the pool to be sure that all the joints, legs
and beams fit into each other. Ensure that all pins are in position by
pushing them downwards through the holes
(see drawing 7.1)
.
Pull gently, in an outward direction, the bottom of the leg making sure
the leg is vertical and perpendicular to the level ground.
3. Filling of the pool
See Krystal Clear™ filter pump manual, install the strainer nuts, flat
strainer rubber washers and threaded strainer connectors on the liner
pre-cut holes. Use strainer valve caps
(19)
and plug them into the
threaded strainer connectors from the inside of the pool so water will not run out while filling.
Before filling the pool with water, ensure that the drain plug inside the pool is closed and that the drain
cap on the outside is screwed on tightly. Fill the pool with no more than 1 inch (2.5 cm) of water. Check
to see whether the water is level.
IMPORTANT: If the water in the pool flows to one side, the pool is not completely level. Setting up
the pool on unlevel ground will cause the pool to tilt resulting in the sidewall material bulging and
a potential collapse of the pool. If the pool is not completely level, you must drain the pool, level
the area or move the pool to a different area that is level, and re-fill the pool, following the above
directions.
Smooth out the bottom liner wrinkles (from inside the pool) by pushing out where the pool floor and pool
sides meet. Or, (from outside pool) reach under the side of the pool, grasp the pool floor and pull in
an outward direction. If the ground cloth is causing the wrinkles, have 2 people pull from opposite sides to
remove all wrinkles. Use the properly assembled pool ladder when entering or exiting the pool during this
process.
4
. Fill the pool with water up to just below the sleeve line.
(see drawing 7.2)
.
6.1
5
6
3
6.2
4
7.1
7.2
WATER LEVEL
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 12
POOL ENCLOSURE SETUP
Once the pool has been filled with water, and it has been confirmed that it is completely level and that all
vertical legs are positioned in the middle of each patio block, proceed with the assembly of the pool
enclosure.
1. Top clamp installation
Fasten a top clamp
(16)
to the T-joint of the pool frame from the underneath. Ensure the two bolts on
top clamp are facing upward. Repeat the procedure until all the top clamps are fastened to the T joints
of the pool frame (see drawings 8.1 & 8.2).
2. Bottom cap and bottom rail installation
Place a bottom cap
(25)
on the ground and align it with the leg cap. Ensure that the threaded side hole
in the bottom cap is facing outward. Place all bottom caps in position.
Starting at any location, but always working in the same direction, connect a bottom rail
(24)
in between
two bottom caps
(25)
. Ensure the pre-drilled holes on the bottom rail hook through the knobs on the
bottom cap. Repeat this procedure in a circular fashion until all the bottom rails and bottom caps have
been connected. Adjust the distance of the bottom cap to the leg cap by estimating that the support
post
(17)
will stand vertical after it is installed (see drawings 9.1 & 9.2).
3. Support post installation
Remove the cardboard inserts from the both slides of each support post.
Insert the support post
(17)
into the bottom cap
(25)
. Lift up the support post slightly to let the slot on
the upper end of the support post hook onto the ridge at the top clamp. Push downward to ensure the
support post is connected firmly with the top clamp and inserted in the bottom cap (see drawings 10.1,
10.2 & 10.3).
Repeat these procedures until all the support posts are joined to the top clamps and bottom caps (see
drawing 10.4).
8.1 8.2
9.1
9.2
10.1
10.2
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 13
POOL ENCLOSURE SETUP (continued)
4. Side panel installation
The number of the side panels depends of the size of your pool. There are two side panels which need
special attention during installation: First, the side panel which needs to be installed outside the pool inlet
& outlet holes, and second, the side panel with the warning panel which needs to be installed in a location
that the warning display is easily seen by pool users before entering the pool. The side boards for these
two special panels are wrapped separately from others.
4a. Side panel with holes installation
Locate the side panel with holes outside the pool liner where the inlet & outlet holes are located.
Unwrap the side boards from pack and slide the side board combination with one hole
(23)
first down
the support posts and insert onto the vertical edge of the bottom rail. Follow with the number sequence
from bottom to top. The groove of the board needs to be inserted fully onto the tongue of previous
board. The printing on the side boards needs to be facing outward. Then slide the side board
combination with two holes
(22)
marked with number “5 & 6” through the support posts and insert onto
the tongue of side board marked with number “4” (see drawings 11.1 & 11.2).
In clockwise motion screw the plunger valve connectors
(18)
onto the threaded strainer connectors which
were already installed on the pool liner during the pool set up (see drawing 11.3). In a clockwise motion
screw the plunger valves onto the plunger valve connectors
(18)
. Close the plunger valves by pushing the
handle down and turn in a clockwise direction to lock as described in filter pump manual. Now, the
strainer valve caps
(19)
can be unplugged out of the threaded strainer connectors from the inside of the
pool (see drawings 11.4 & 11.5).
Continue to finish the side panel installation by installing the rest of the side boards marked with number “7”
and “8” (see drawing 11.6).
10.3
10.4
11.1
11.2
11.3
11.4 11.5
11.6
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 14
POOL ENCLOSURE SETUP (continued)
4b. Side panel with “warnings” installation
Locate the side panel with warnings such that the warnings will be easily seen by pool users before
entering the pool. Unwrap the side boards from pack and slide the side board first down the support
posts and insert onto the vertical edge of the bottom rail. Follow with the number sequence from bottom
to top. The groove of the board needs to be inserted fully onto the tongue of the previous board. The
printing on the side boards needs to be facing outward (see drawings 12.1 & 12.2).
12.1
12.2
15'8" x 49"
18’8” x 53”
11.7
8
7
6
5
4
3
2
1
11.8
8
7
6
5
4
3
2
1
0
15'8" x 49"
12.3
8
7
6
5
4
3
2
1
15'8" x 49"
18’8” x 53”
12.4
8
7
6
5
4
3
2
1
0
18’8” x 53”
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 15
POOL ENCLOSURE SETUP (continued)
4c. Other side panel installation
For 49” height pool, install the rest of the side panels by using eight pieces of side boards A
(20)
each.
For 53” height pool, install the rest of the side panels by using one piece of side board B
(21)
at the
bottom plus eight pieces of side boards A
(20)
each. Install the side boards one by one from bottom to
top. Insert the groove of the first side board onto the vertical edge of the bottom rail, and the groove
of the other side boards onto the tongue of each previous board. The side boards with wood veins
printed need to be faced outward (see drawings 13.1 & 13.2).
5. Top Board Installation
Attach the top board
(15)
on the top of the side panel, with the holes at its two ends aligning with the nuts
on the top clamps
(16)
. Make sure the groove underneath the top board fits firmly onto the tongue of the
top board
(15)
. Repeat this procedure until all the top boards are fixed to the top clamps and side boards.
NOTE:
There are four pieces of top board which are printed with warnings. Install those four top boards
three pieces apart from each other (see drawings 14.1, 14.2 & 14.3).
6. Top Clamp Cover Installation
Install the top clamp cover
(14)
where the two top boards meet. Insert the ridge of top clamp cover into
the slot on the top end of the support post. Align the top holes on top clamp cover with the nuts of the top
clamp. Insert and screw bolt
(13)
to each of the threaded holes by using the wrench
(26)
provided, and
then cover with the waterproof caps
(12)
. Repeat this procedure until all the top clamp covers are fixed to
the top clamps and support posts (see drawings 15.1, 15.2 & 15.3).
14.1
14.2
14.3
13.1
13.2
15.2
15.3
15.1
NOTE:
Drawings for illustration
purpose only.
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 16
TROUBLESHOOTING
PROBLEM
DESCRIPTION
CAUSE
SOLUTION
ALGAE
COLORED
WATER
FLOATING
MATTER IN
WATER
CHRONIC LOW
WATER LEVEL
SEDIMENT ON
POOL BOTTOM
SURFACE DEBRIS
Greenish water.
Green or black spots
on pool liner.
Pool liner is slippery
and/or has a bad odor.
Water turns blue,
brown, or black when
first treated with
chlorine.
Water is cloudy or
milky.
Level is lower than
on previous day.
Dirt or sand on pool
floor.
Leaves, insects etc.
Chlorine and pH level
need adjustment.
Copper, iron or
manganese in water
being oxidized by the
added chlorine.
"Hard water" caused by
a too high pH level.
Chlorine content is low.
Foreign matter in water.
Rip or hole in pool liner
or hoses.
Heavy use, getting in
and out of pool.
Pool too close to trees.
Super chlorinate with shock
treatment. Correct pH to your
pool store's recommended level.
Vacuum pool bottom.
Maintain proper chlorine level.
Adjust pH to recommended
level.
Run filter until water is clear.
Replace cartridge frequently.
Correct the pH level. Check with
your pool dealer for advice.
Check for proper chlorine level.
Clean or replace your filter
cartridge.
Repair with patch kit.
Finger tighten all caps.
Replace the hoses.
Use Intex pool vacuum to
clean bottom of pool.
Use Intex pool skimmer.
Water maintenance
The maintenance of a proper water balance through appropriate use of sanitizers is the single most
important factor in maximizing the life and appearance of the liner as well as ensuring clean, healthy
and safe water. Proper technique is important for water testing and treating the pool water. See your
pool professional for chemical, test kits and testing procedures. Be sure to read and follow the
written instructions from the chemical manufacturer.
1
. Never let chlorine come in contact with the liner if it is not completely dissolved. Dissolve granular or
tablet chlorine first in a bucket of water, then add it to the pool water. Likewise with liquid chlorine; mix it
immediately and thoroughly with the pool water.
2
. Never mix chemicals together. Add the chemicals to the pool water separately. Thoroughly dissolve each
chemical before adding another one to the water.
3
. An Intex pool skimmer and an Intex pool vacuum are available to assist in maintaining clean pool water.
See your pool dealer for these pool accessories.
4
. Do not use a pressure washer to clean the pool.
POOL MAINTENANCE & CHEMICALS
REMEMBER TO
• Protect all pool occupants from possible water-related illnesses by keeping the pool water
clean and sanitized. Do not swallow the pool water. Always practice good hygiene.
• Keepyourpoolcleanandclear.Thepoolfloormustbevisibleatalltimesfromtheoutside
barrier of the pool.
• Keepchildrenawayfrompoolcoverstoavoidentanglement,drowning,orotherserious
injury.
WARNING
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 17
EXCESSIVE RAIN: To avoid damage to the pool and over filling, immediately drain rain water that
causes the water level to be higher than the maximum.
How to Drain Your Pool and Long Term Storage
1
. Check local regulations for specific directions regarding disposal of swimming pool water.
2
. Check to make sure that the drain plug inside the pool is plugged in place.
3
. Remove the cap from the drain valve on the outside pool wall.
4
. Attach the female end of the garden hose to the drain connector.
5
. Place the other end of the hose in an area where the water can be safely drained away from the house
and other nearby structures.
6
. Attach the drain connector to the drain valve.
NOTE: The drain connector will push the drain plug
open inside the pool and water will start to drain immediately.
7.
When the water stops draining, start lifting the pool from the side opposite the drain, leading any
remaining water to the drain and emptying the pool completely.
8
. Disconnect hose and adapter when finished.
9
. Re-insert drain plug in drain valve on inside of pool for storage.
10
. Replace drain cap on outside of pool.
11
. Reverse set-up instructions to disassemble the enclosure and pool, and remove all connecting parts.
12
. Be sure that the pool and all parts are completely dry before storage. Air dry the liner in the sun until
completely dry before folding
(see drawing 20)
. Sprinkle some talcum powder to prevent the vinyl from
sticking together and to absorb any residual missed.
13
. Create a square shape. Starting at one side, fold one-sixth of liner in on itself twice. Do the same on the
opposite side
(see drawings 21.1 & 21.2)
.
14
. Once you have created two opposing folded sides, simply fold one over the other like closing a book
(see drawings 22.1 & 22.2)
.
15
. Fold the two long ends to the middle
(see drawing 23)
.
16
. Fold one over the other like closing a book and finally compact the liner
(see drawing 24)
.
17
. Store the liner and accessories in a dry, temperature controlled, between 32 degrees Fahrenheit
(0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius), storage location.
18
. The original packing can be used for storage.
22.1
20
21.1
21.2
22.2
23 24
POOL MAINTENANCE & DRAINAGE
Do not add chemicals if the pool is occupied. This can cause skin or eye irritation.
Concentrated
chlorine solutions can damage the pool liner. In no event is Intex Recreation Corp., Intex Development Co.
Ltd., their related companies, authorized agents and service centers, retailers or employees liable to the
buyer or any other party for costs associated with the loss of pool water, chemicals or water damage.
Keep
spare filter cartridges on hand. Replace cartridges every two weeks.
We recommend the use of a
Krystal Clear™ Intex Filter Pump with all of our above-ground-pools.
CAUTION
ALWAYS FOLLOW THE CHEMICAL MANUFACTURER'S
DIRECTIONS, AND THE HEALTH AND HAZARD WARNINGS.
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 18
WINTER PREPARATIONS
Winterizing your Above Ground Pool
After usage, you can easily empty and store away your pool in a safe place. You must
drain, disassemble and properly store the pool when the temperature drops below 41
degrees Fahrenheit (5 degrees Celsius) to prevent ice damage to the pool and related
components. Ice damage can result in sudden liner failure or pool collapse. Also see the
section ‘’How To Drain Your Pool’’.
Should temperatures in your area not drop below 41 degrees Fahrenheit (5 degrees
Celsius), and you choose to leave your pool out, prepare it as follows:
1.
Clean the pool water thoroughly. If the type is an Easy Set Pool or an Oval Frame Pool,
make sure that the top ring is properly inflated.
2.
Remove the skimmer (if applicable) or any accessories attached to the threaded strainer
connector. Replace strainer grid if necessary. Be sure all accessories parts are clean and
completely dry before storage.
3.
Plug the Inlet and Outlet fitting from the inside of the pool with the plug provided (sizes 16'
and below). Close the Inlet and Outlet Plunger Valve (sizes 17' and above).
4.
Remove the ladder (if applicable) and store in a safe place. Be sure the ladder is completely
dry before storage.
5.
Remove the hoses that connect the pump and filter to the pool.
6.
Add the appropriate chemicals for the winter period. Consult your local pool dealer as to
which chemicals you should use and how to use them. This can vary greatly by region.
7.
Cover pool with Intex Pool Cover.
IMPORTANT NOTE: INTEX POOL COVER IS NOT A
SAFETY COVER.
8.
Clean and drain the pump, filter housing and hoses. Remove and discard the old filter
cartridge. Keep a spare cartridge for the next season.
9.
Bring pump and filter parts indoors and store in a safe and dry area, preferably between 32
degrees Fahrenheit (0 degrees Celsius) and 104 degrees Fahrenheit (40 degrees Celsius).
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves inherent risks of
injury and death. To reduce your risk of injury, read and follow all product, package and
package insert warnings and instructions. Remember, however, that product warnings,
instructions and safety guidelines cover some common risks of water recreation, but do
not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following general guidelines
as well as guidelines provided by nationally recognized Safety Organizations:
Demand constant supervision. A competent adult should be appointed as a “lifeguard” or
water watcher, especially when children are in and around the pool.
Learn to swim.
Take the time to learn CPR and first aid.
Instruct anyone who is supervising pool users about potential pool hazards and about the use
of protective devices such as locked doors, barriers, etc.
Instruct all pool users, including children what to do in case of an emergency.
Always use common sense and good judgement when enjoying any water activity.
Supervise, supervise, supervise.
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2016
English
Page 19
LIMITED WARRANTY
Your Intex Pool has been manufactured using the highest quality materials and
workmanship. All Intex products have been inspected and found free of defects prior to
leaving the factory. This Limited Warranty applies to the Intex Pool only.
This limited warranty is in addition to, and not a substitute for, your legal rights and
remedies. To the extent that this warranty is inconsistent with any of your legal rights, they
take priority. For example, consumer laws across the European Union provide statutory
warranty rights in addition to the coverage you receive from this limited warranty: for
information on EU-wide consumer laws, please visit the European Consumer Center
website at http://ec.europa.eu/consumers/ecc/contact_en/htm.
The provisions of this Limited Warranty apply only to the original purchaser and are not
transferable. This Limited Warranty is valid for a period of 90 days from the date of the
initial retail purchase. Keep your original sales receipt with this document, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty
will be invalid.
If you find a manufacturing defect in the Intex Pool during the warranty period, please
contact the appropriate Intex Service Center listed in the separate “Authorized Service
Centers” sheet. If the item is returned as directed by the Intex Service Center, the Service
Center will inspect the item and determine the validity of the claim. If the item is covered by
the provisions of the warranty, the item will be repaired or replaced, with the same or
comparable item (at Intex’s choice) at no charge to you.
Other than this warranty, and other legal rights in your country, no further warranties are
implied. To the extent possibly in your country, in no event shall Intex be liable to you or
any third party for direct or consequential damages arising out of the use of your Intex Pool,
or Intex or its agents’ and employees’ actions (including the manufacture of the product).
If your country does not allow the exclusion or limitation of incidental or consequential
damages, this limitation or exclusion does not apply to you.
You should note that this limited warranty does not apply in the following circumstances:
If the Intex Pool is subject to negligence, abnormal use or application, accident,
improper operation, improper maintenance or storage.
If the Intex Pool is subject to damage by circumstances beyond Intex’s control, including
but not limited to, punctures, tears, abrasions, ordinary wear and tear and damage
caused by exposure to fire, flood, freezing, rain, or other external environmental forces;
To parts and components not sold by Intex; and/or
To unauthorized alterations, repairs or disassembly to the Intex Pool by anyone other
than Intex Service Center personnel.
The costs associated with the loss of pool water, chemicals or water damages are not
covered by this warranty. Injury or damage to any property or person is not covered by this
warranty.
Read the owner’s manual carefully and follow all instructions regarding proper operation
and maintenance of your Intex Pool. Always inspect your product prior to use. This limited
warranty will be void if use instructions are not followed.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex Graphite Gray Panel - 26384NP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex Graphite Gray Panel - 26384NP in de taal/talen: Engels als bijlage per email.

De handleiding is 3,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Intex Graphite Gray Panel - 26384NP

Intex Graphite Gray Panel - 26384NP Gebruiksaanwijzing - Nederlands - 20 pagina's

Intex Graphite Gray Panel - 26384NP Gebruiksaanwijzing - Deutsch - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info