752348
38
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
English
Krystal Clear
TM
Sand Filter Pump
16” (410mm) & Saltwater System
Model CS20110
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual, without notice.
OWNER’S MANUAL
For illustrative purposes only.
159-***-R0-1307
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 2
English
TABLE OF CONTENTS
Warnings.......................................................................... 3
Parts List & References.................................................. 4-8
Setup Instructions ......................................................... 9-16
Product Specifications................................................... 11
Operating Instructions .................................................. 17-21
LED Code Chart.............................................................. 22
Salt & Pool Water Volumes............................................ 23
Intex Pools Salt Table...................................................... 24
Intex Pools Cyanuric Acid Table.................................... 25
Intex Pools Operating Time Table ................................. 26
Non-Intex Pools Salt Table.............................................. 27
Non-Intex Pools Cyanuric Acid Table............................ 27
Non-Intex Pools Operating Time Table.......................... 27
Maintenance.................................................................... 28-32
Long Term Storage.......................................................... 32
Troubleshooting Guide................................................... 33-35
Common Pool Problems................................................. 36
General Aquatic Safety................................................... 37
Limited Warranty............................................................. 38
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 3
English
SAFETY RULES
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
Children must stay away from this product and electrical cord(s).
Assembly and disassembly by adults only.
Risk of electric shock. Connect only to a grounding type receptacle, this product
is provided with a ground-fault circuit interrupter. If replacement of the plug or cord
is needed, use only identical replacement parts.
Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
•Theunitisprovidedwithaground-faultcircuitinterrupter(GFCI).TotesttheGFCI,
push the test button. TheGFCIshouldinterruptpower.Push the reset button,
powershouldberestored.IftheGFCIfailstooperateinthismanner.TheGFCIis
defective.IftheGFCIinterruptspowertothepumpwithoutthetestbuttonbeing
pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
To reduce the risk of electric shock, replace damaged cord immediately. Use a
qualified electrician to replace the cord.
To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
Donotuseanapplianceleakagecurrentinterrupter(ALCI)inplaceofaGFCI
since the ALCI will not protect people.
•Positionthisproductawayfrompool,soastopreventchildrenfromclimbingonit
and access the pool.
Do not operate this product when pool is occupied.
To reduce the risk of entrapment hazard, never enter the pool if suction strainer
component is loose, broken, cracked, damaged or missing. Replace loose, broken,
damaged, cracked or missing suction strainer components immediately.
•Neverplayorswimnearsuctionfittings.Yourbodyorhairmaybetrappedcausing
permanent injury or drowning.
•Topreventequipmentdamageandriskofinjury,alwaysturnpumpoffbefore
changing the filter control valve position.
•Neveroperatethisproductabovethemaximumworkingpressurestatedonthe
filter tank.
•HazardousPressure.Impropertankvalvecoverassemblycouldcausethevalve
cover to blow off and cause serious injury, property damage or death.
•Thisproductisintendedtobeusedonlyforthepurposesdescribedinthemanual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
This product is for use with storable pools only. Do not use with permanently-installed pools.
A storable pool is constructed so that it is capable of being readily disassembled for storage
and reassembled to its original integrity. A permanently-installed pool is constructed in or on
the ground or in a building such that it cannot be readily disassembled for storage.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
CAUTION
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 4
English
PARTS LIST
PARTS LIST
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
7
1
9
45
2
6
3
8
10 11 12
13 14 15
16 17 18
19 20 21
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 5
English
PARTS LIST (continued)
PARTS LIST
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
22 2423
34 35 36
31 32 33
28 29 30
25 26 27
37
40
38 39
41
Optional
Optional Optional
42
51 52
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 6
English
PARTS REFERENCE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
1
5
9
10 11
21
2
13 14
20 19
3
6
7
4
12
15
16
17
18
8
22
23
24
25
26
27
41
18
50
43
47
44
45
49
48
46
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 7
English
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
PARTS REFERENCE
28
29
30 31 32 33 34
28
29
30 35 36 37
28
29
30 35 36 38
28
29
30 31 32 33 38
51
51
51
51
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 8
English
When ordering parts, be sure to quote the model number and part numbers.
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
PARTS REFERENCE
REF. NO. DESCRIPTION QTY. SPARE PART NO.
1PRESSUREGAUGE 1 11224
2 6-WAYVALVESET 1 11496
3 DRAINOUTLETCOVER 1 11131
4 TANKO-RING 1 11379
5 SCREW 2 11381
6 CLAMP 1 11380
7SANDSHIELD 1 11382
8CENTERPIPEHUB 1 11495
9DRAINVALVECAP 1 11456
10 DRAINVALVEO-RING 1 11385
11 LATERAL 10 11384
12 HOSEWITHNUTS 2 11009
13 SANDFILTERINTERCONNECTINGHOSE 1 11536
14 LEAFTRAPNUT 1 11479
15 LEAFTRAPO-RING 1 11232
16 BASKET 1 11260
17 FILTERHOUSINGNUT 1 11261
18 L-SHAPEO-RING 4 11228
19 SEDIMENTRELEASEVALVE 1 10460
20 VALVEO-RING 1 10264
21 FLOWSENSOR 1 11460
22 ELECTROLYTICCELL 1 11372
23 TITANIUMELECTRODE 1 11374
24 COPPER ELECTRODE 1 11234
25 PRE-FILTERASSEMBLY 1 11371
26 PUMPMOTOR&CONTROL 1 11377
27 L-SHAPEO-RING 1 11439
28
PLUNGERVALVE(HOSEO-RING&STEPWASHERINCLUDED)
2 10747E
29 HOSEO-RING 2 10262
30 STEPWASHER 2 10745
31 STRAINERNUT 2 10256
32 FLATSTRAINERRUBBERWASHER 2 10255
33
THREADEDSTRAINERCONNECTOR
2 10744
34 ADJUSTABLEPOOLINLETNOZZLE 1 11074
35 ADAPTORB 2 10722
36 STRAINERCONNECTOR(OPTIONAL) 2 11070
37 POOLINLETNOZZLE(OPTIONAL) 1 11071
38 STRAINERGRID(OPTIONAL) 1 11072
39 CHLORINETESTSTRIPS 1 19635
40 COPPER TEST STRIPS 1 11254
41 LEAFTRAPCOVER 1 11480
42 STRAINERGRID 1 10253
43 ELECTROLYTICCELLNUT 1 11432
44 COPPERELECTRODEO-RING 1 11440
45 COPPERELECTRODEHOUSING 1 11441
46 SANDFILTERPUMPMOTORINLETO-RING 2 11457
47 COPPERELECTRODENUT 1 11488
48 16"SANDFILTERPUMPANDCOMBOTANK 1 11497
49 16"SANDFILTERPUMPTANKBASE 1 11514
50 O-RINGONTITANIUMPLATES 1 11515
51 VACUUMRELEASEVALVE 2 11437
52 VACUUMRELEASEVALVECAP 2 11576
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 9
English
SETUP INSTRUCTIONS
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. If your pool has an inflatable top ring, install the strainer, nozzle
and plunger valve before inflating the pool liner top ring. The part numbers
here onward refer to the parts depicted in the Parts List section of this
manual. To install, do the following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (33) (see drawing 1).
Becarefulnottolosethesteprubber
washer (30). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (31) from the threaded
connector (33). Leave the flat washer (32)
on the connector (33).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
Fromtheinsideofthepoollinerinsertthe
connector (33) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Beforeassembly,lubricatethethreadswith
a petroleum jelly. With the flat side of the
strainer nut (31) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (31) back onto the threaded
connector (33) (see drawing 2).
5. Fingertightenthestrainernut(31) onto the
threaded connector (33).
6. Grasptheplungervalveassembly.Make
sure the step washer (30) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (33) (see drawing 3).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during filling
of the pool (see drawing 4.1).
9. NOTE: Nevercoverthevacuumrelease
valve (51) unless it is damaged or leaking.
Replace the vacuum release valve
immediately.
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
1
2
3
32 33
INSIDE
LINER WALL
31
4.2
2
1
1
2
4.1
INSIDE
LINER WALL
30
WATER
FLOW
POOL
51
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 12
English
4. In a clockwise motion screw filter housing nut (17) onto the motor water inlet
(See drawings 12.1 & 12.2).
5. Replace the basket (16) and leaf trap cover (14) back to the pre-filter housing
(See drawings 13.1 & 13.2).
SETUP INSTRUCTIONS (continued)
SETUP INSTRUCTIONS
Sand tank installation:
1. Place the tank support base at the selected location.
2. Place the tank on the tank support base (See drawing 14.1).
3. Connect the motor pre-filtering assembly unit to the tank support base (See
drawing 14.2). NOTE: Ensure the pre-filter housing water inlet hose connection
is facing towards the pool.
IMPORTANT: Some countries, especially in the European community,
require the product to be secured to the ground or to a base in a
permanent upright position. Check your local authorities to determine if
there is a regulation in your area regarding above-the-ground swimming
pool filter-pumps. If yes, then the product can be mounted to a platform
using the two holes located in the base. See drawing 14.3.
The product can be mounted on a cement base or onto a wooden
plat form to prevent accidental falling over.
• Themountingholesare6.4mmindiameterandspaced177.4mm
apart.
• Usetwoboltsandlocknutswithamaximumof6.4mmindiameter.
13.1 13.2
14.1 14.2
177.4 mm
14.3
16
14
12.2
12.1
17 17
41
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 13
English
SETUP INSTRUCTIONS (continued)
SETUP INSTRUCTIONS
Sand loading:
IMPORTANT: Use No. 20 silica sand or glass sand with particle size range
0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less
than 1.75.
NOTE: Before loading the tank with sand, ensure the center pipe hub
assembly is securely in place at the bottom of the tank, and vertically
centered inside the tank.
1. Place the sand shield (7) over the top of the center pipe. Pour the sand into the
tank at a slow rate. (see drawing 15).
2. Fillthetankapproximatelyhalfway,removethesandshield (7). (see
drawing 16).
3. Evenly distribute the sand inside the tank, then fill the tank with some water to
provide a cushioning effect when the remaining sand is poured in. This
prevents the center pipe hub (8) from excessive shock (see drawing 17).
Place the sand shield (7) back and continue to pour the sand into the tank.
4. Sandshallbefilledbetweenthe“MAX”and“MIN”markedgaugeonthecenter
pipe. Evenly spread and level out the sand by hand (see drawings 17 & 18).
5. Remove the sand shield (7).
6. Wash away all sand around the top edge of the tank.
15 16
77
MAX
MIN
17
MAX
MIN
MAX
MIN
18
8
8
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 14
English
6-way valve installation:
1. Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding
underneath the 6-way valve fits securely into the center pipe hub (8) top opening (see
drawing 19).
IMPORTANT: There are three hose connection ports on the 6-way valve, ensure
the outlet connection (from filter to the pool) on the valve is facing towards the
pool, and the inlet connection (from motor to valve) is aligned with the motor
outlet (see drawing 20).
2. Remove the clamp bolt, and install the clamp around the tank and 6-way valve flanges,
then replace the clamp bolt and use a phillips screwdriver (not included) to tighten it.
(see drawing 21).
SETUP INSTRUCTIONS
SETUP INSTRUCTIONS (continued)
WARNING
Improper tank valve and clamp assembly could cause the valve and clamp
to blow off and cause serious injury, property damage or death.
3. Connect the sand filter interconnecting hose (13) between the 6-way valve inlet and
motor outlet, and insert the electrolytic cell (22)intothe6-wayvalveoutlet.Handtighten
them securely (see drawings 22 and 23).
22 23
4. Screw and tighten the flow sensor (21) to the electrolytic cell (22), then plug in the
electrolytic cell line cord and tighten the nut (see drawings 24 and 25).
24 25
13
21
22
22
6
19 20
WATER
INLET
WATER
OUTLET
21
8
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 15
English
SETUP INSTRUCTIONS
SAND FILTER PUMP HOSE CONNECTION SETUP
The 6-way valve has three hose connection ports.
1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose
to the lower plunger valve with the strainer. Ensure the hose nuts are securely
tighten.
2. Connect the second hose (12) between the electrolytic cell outlet and the
upper plunger valve with the inlet-nozzle. Ensure the hose nuts are securely
tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be
directed to a proper draining receptacle using a hose or pipe (not provided).
Remove the drain cap before attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.
WARNING
• Positionthisproductawayfromthepool,soastopreventchildrenfrom
climbing on it and accessing the pool.
6-WAY VALVE
WATER LEVEL
ADJUSTABLE
POOL INLET
NOZZLE
THREADED
STRAINER
CONNECTOR
OUTSIDE
LINER WALL
PLUNGER
VALVE
(ILLUSTRATION NOT TO SCALE)
TO
DRAIN
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 18
English
Initial startup and operation:
Before operating, be sure that:
• Allthehoseshavebeenconnectedandtightenedsecurely,andcorrectamount
of filter sand have been loaded.
• Theentiresystemisconnectedtoagroundingtypereceptacleprotectedbya
ground-faultcircuitinterrupter(GFCI)orresidualcurrentdevice(RCD).
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should never be
on when the valve is in the closed position. If the pump is operated with
the valve closed, and explosive situation could exist.
1. Turn both plunger valve handles fully counter-clockwise until they stop. This
opens the valves to allow water to flow into the sand filter pump.
NOTE: The plunger valve is equipped with a vacuum release valve that will
automatically activate to minimize the suction at the pool outlet if the outlet is
blocked. This is an additional safety feature to prevent suction entrapment.
The vacuum release valve will reset once the blockage is removed and the
pump is switched off. To restart the system the air must be removed from the
filter pump per previous step.
2. Ensure the drain/waste outlet on the 6-way valve is not covered and directed to
a proper draining receptacle.
3. Ensure the pump is off, depress the 6-way
valve and turn it to the “BACKWASH
position (see drawings 27 & 32).
IMPORTANT: To prevent damage to the
6-way valve, always depress the valve
handle before turning. Always switch off
pump before changing the 6-way valve
position.
4. Switch on the pump (see drawing 33). Water
is circulating backward through the sand
mediaandtowaste/drainoutlet.Backwash
until a clear flow of water is observed in the
waste/drain outlet or through the drain sediment
window.
NOTE: The initial backwash of the filter is
recommended to remove any impurities or fine
sand particles in the sand media.
32
1
2
33
OFF
ON
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
29
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
30
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
31
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 19
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (continued)
English
5. Switchoffthepump,changethe6-wayvalveto“RINSE”position(see
drawing 28).
6. Switch on the pump and run the pump for about one minute to level out the
sand bed after backwashing the sand media.
7. Switchoffthepump,changethe6-wayvalveto“FILTER”position(see
drawing 26).
8. Switch on the pump. The system is now operating in the normal filtering mode.
Run the pump until the desired pool water clearance is obtained and no more
than 12 hours per day.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash
frequently due to unusual heavy dirt present in the water and sand. After that,
as the filter removes dirt and impurities from the pool water, the accumulated
dirt in the sand media will cause the pressure to rise and the flow to diminish. If
there is no vacuuming device attached to the system and the pressure gauge
reading is in the yellow zone it is time to backwash the sand media, see
“BACKWASH”under“initialstartupandoperation”section.
Vacuumingdevice(i.e.Intexautopoolcleaner)attachedtothesystemmay
also cause the flow to diminish and the pressure to rise. Remove any
vacuuming device from the system and check if the pressure gauge reading has
dropped from the yellow zone to the green zone.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassB
digitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedto
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 20
English
SALTWATER SYSTEM OPERATION
OPERATING INSTRUCTIONS
1. Start up the unit:
Plug the power cord into the electrical outlet and test
theGFCI/RCD(circuitbreaker).Switchontheunit.
WiththeFilterPumpturned“ON”andoperating.
Flashingcode“00”appearsontheelectroniccontrol
station’s LED, indicating that the unit is ready to be
programmed.
2. Set operating hours for Saltwater System:
With code “00” flashing, press button to
set the desired operating hours. See the
“Operating Time Table” for the required
operating hours related to each pool size.
Pressing will increase the time from 01
to 12 hours maximum. If you have selected
too many hours keep pressing to repeat
the cycle. The built-in timer will now activate
your Saltwater System, at the same time
each day, for the number of hours you have set.
NOTE: The Saltwater System will not operate if the filter pump is not operating.
3. Lock keypad controls:
With the desired hour value showing, press button until
youheara“beep”.Thegreen“WORKING”indicatoronthe
control panel will light up within a few seconds to indicate that
the saltwater system has started sanitizer production. Locking
the control buttons into this setting prevents unauthorized
changing of the operating cycle.
NOTE: If you forget to lock the keypad controls, the system
will automatically lock it and start working 1 minute later.
4. Readjust operating time if necessary:
The operating hours can be re-adjusted if necessary.
Press button until you hear a “beep” to unlock the
keypad and the current programmed time will flash.
Repeat steps 2 to 3.
5. Test the copper concentration in the
pool water.
The Saltwater System recommends a copper
level of 0.1 to 0.2 ppm.
This is easily tested by the copper ion test
strips provided. If the test result is
0.1~0.2ppm, go directly to step 7.
OK
0
Copper (ppm)
0.1 0.2 0.5 0.9 1.3
(1 to 12 hours max per cycle)
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 21
English
SALTWATER SYSTEM OPERATION (continued)
OPERATING INSTRUCTIONS
6. Boost cycle
Ifthetestresultisbelow0.1ppm,pressandhold“BOOST”
button for 5 seconds until the indicator lights up and the
LED display display “80”. This indicates that the saltwater
system has started copper ion and more chlorine sanitizer
production.Youcanpressandholdthe“BOOST”buttonfor
another 5 seconds until the indicator is off, which will cancel
theBoostcycle.
Note: Once the system has started copper ion and more
chlorine sanitizer production, the boost button can’t be re-set until the power
switch is off.
The boost operating hours is 8 times the amount of time programmed into the
system, i.e. if your saltwater system operating time is 2 hours, the boost procedure
will run 8 x 2 = 16 hours. After boost procedure has been completed, the system
will automatically switch to the normal working mode.
Afteraheavyrainorifthepoolisdirty,pressthe“BOOST”buttontoshockthe
pool again.
7. Test pool water regularly:
Once the copper level appears to be balanced, test the pool water every week
to maintain the proper sanitizer level.
It’s very important that the free chlorine is between 0.5-3 ppm and copper
ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1
ppm, repeat step 6.
NOTE:AHighcopperionconcentrationmaycauseblondehairtoexhibita
green hair. To prevent this, wear a swimming cap during swimming, and wash
hair with special shampoo after using the pool.
See“TroubleshootingGuide”.
8. Stand-by/power saving mode:
When the cycle ends, the green “SLEEP” indicator on the
control panel lights up and the LED display flashes “93”.
ThesystemisnowinStand-Bymode.Afterawhile,it
shuts down and sets itself in a Power Saving mode. The
system will automatically turn itself back on in 24 hours,
starting its daily cycle of chlorine production.
The “SLEEP” indicator stays on, while the system is in the
Power Saving mode. The LED display however, goes blank
after 1 hour. Press any button ( or ) to view the last LED
code.
9. Running the pump alone without the Saltwater System:
To run the pump alone without the Saltwater System function,
press and hold both ( ) and ( ) buttons for 5 seconds
untilyouheara“beep”andtheLEDdisplayshows“FP”.
The pump is now operating alone. To stop the pump,
manuallyturntheswitchOFF.NOTE: The pump cannot
be operated alone under an automatic timer mode.
IMPORTANT: To keep the initial automatic operating cycle
settingoftheSaltwaterSystem,turntheswitchON,the
LEDdisplayshows“FP”,thenunlockandlockthekeypad
controls again, see previous steps 2 and 3. The LED display shows
the initial input hours and the Saltwater System cycle repeats again.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 22
English
LED CODE CHART
LED CODE CHART
LED Reading Definitions
FP FilterPumpWorkingMode
80 BoostMode
00 Stand-ByMode(Start-up)
01 MinimumOperatingHour(1hourremaining)
02 OperatingHours(2hoursremaining)
03 OperatingHours(3hoursremaining)
04 OperatingHours(4hoursremaining)
05 OperatingHours(5hoursremaining)
06 OperatingHours(6hoursremaining)
07 OperatingHours(7hoursremaining)
08 OperatingHours(8hoursremaining)
09 OperatingHours(9hoursremaining)
10 OperatingHours(10hoursremaining)
11 OperatingHours(11hoursremaining)
12 MaximumOperatingHours(12hoursremaining)
90 AlarmCode(LowPumpFlow/NoFlow)
91 Alarm Code (Low Salt Level)
92 AlarmCode(HighSaltLevel)
93 Stand-ByMode(OperatingProcessfinished)
“BLANK” NoPoweror“PowerSavingMode”waitingtostartnext
Saltwater System cycle.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 25
English
INTEX POOLS CYANURIC ACID TABLE
Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet rays. To
maintain the pool water clear and clean, and to maximize the performance of the device, add
cyanuric acid to the pool. We recommend that the cyanuric acid level be maintained at
approximately 1% of the salt, i.e. 100 Lbs (45 Kgs) salt x1% = 1 Lbs (0.45 Kgs) cyanuric acid.
If the pool water is dirty, filthy or grimy, DO NOT add chlorine stabilizer (cyanuric acid) as this
will slowdown the sanitation time of the device. Under this condition you must BOOST your
pool water, refer to BOOST cycle steps. Once the pool water has been restored to clear and
clean conditions you may add cyanuric acid.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80% for
Easy Set & Oval Pool)
Cyanuric Acid Needed for
Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
18' x 42" (549cm x 107cm)
4786 18115 1.2 0.5
18' x 48" (549cm x 122cm)
5455 20647 1.4 0.6
CIRCULAR
METAL
FRAME POOL
18' x 48" (549cm x 122cm)
6423 24311 1.6 0.7
21' x 52" (640cm x 132cm)
9533 36082 2.4 1.1
24' x 52" (732cm x 132cm)
12481 47241 3.1 1.4
ULTRA FRAME
POOL
18’ x 48” (549cm x 122cm)
6423 24311 1.6 0.7
18' x 52" (549cm x 132cm)
6981 26423 1.7 0.8
20’ x 48” (610cm x 122cm)
7947 30079 2.0 0.9
22’ x 52” (671cm x 132cm)
10472 39637 2.6 1.2
24’ x 52” (732cm x 132cm)
12481 47241 3.1 1.4
26 ’x 52” (792cm x 132cm)
14667 55515 3.7 1.7
SEQUOIA SPIRIT™
POOL SET
15'8" x 49" (478cm x 124cm)
4440 16805 1.1 0.5
16’8” x 49” (508cm x 124cm)
5061 19156 1.3 0.6
18'8" x 53" (569cm x 135cm)
6981 26423 1.7 0.8
OVAL FRAME
POOL
10’ x 18’ x 42” (305cm x 549cm x 107cm)
2885 10920 0.7 0.3
12' x 20' x 48" (366cm x 610cm x 122cm)
4393 16628 1.1 0.5
RECT. ULTRA
FRAME POOL
9' x 18' x 52" (274cm x 549cm x 132cm)
4545 17203 1.1 0.5
10’ x 20’ x 52” (305cm x 610cm x 132cm)
5835 22085 1.5 0.7
12' x 24' x 52" (366cm x 732cm x 132cm)
8403 31805 2.1 1.0
16' x 32' x 52" (488cm x975cm x 132cm)
14364 54368 3.6 1.6
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 26
English
INTEX POOLS OPERATING TIME TABLE (WITH CYANURIC ACID)
Pool Size
Water Capacity (Calculated at 90%
for Frame Pool and 80% for Easy
Set & Oval Pool)
Operating Time (hours)
at different ambient/air
temperatures
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
18' x 42" (549cm x 107cm)
4786 18115 2 2 3
18' x 48" (549cm x 122cm)
5455 20647 2 3 4
CIRCULAR
METAL
FRAME POOL
18' x 48" (549cm x 122cm)
6423 24311 3 3 4
21' x 52" (640cm x 132cm)
9533 36082 4 5 6
24' x 52" (732cm x 132cm)
12481 47241 6 6 7
ULTRA FRAME
POOL
18’ x 48” (549cm x 122cm)
6423 24311 3 3 4
18' x 52" (549cm x 132cm)
6981 26423 3 4 5
20’ x 48” (610cm x 122cm)
7947 30079 4 4 5
22’ x 52” (671cm x 132cm)
10472 39637 5 5 6
24’ x 52” (732cm x 132cm)
12481 47241 6 6 7
26 ’x 52” (792cm x 132cm)
14667 55515 7 8 8
SEQUOIA SPIRIT™
POOL SET
15'8" x 49" (478cm x 124cm)
4440 16805 2 2 3
16’8” x 49” (508cm x 124cm)
5061 19156 2 3 4
18'8" x 53" (569cm x 135cm)
6981 26423 3 4 5
OVAL FRAME
POOL
10’ x 18’ x 42” (305cm x 549cm x 107cm)
2885 10920 1 1 2
12' x 20' x 48" (366cm x 610cm x 122cm)
4393 16628 2 2 3
RECT. ULTRA
FRAME POOL
9' x 18' x 52" (274cm x 549cm x 132cm)
4545 17203 2 2 3
10’ x 20’ x 52” (305cm x 610cm x 132cm)
5835 22085 3 3 4
12' x 24' x 52" (366cm x 732cm x 132cm)
8403 31805 4 4 5
16' x 32' x 52" (488cm x975cm x 132cm)
14364 54368 7 7 8
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 30
English
POOL CARE & CHEMICALS
• Allpoolsrequirecaretokeepthewaterclearandhygienicallyclean.Withproper
chemical control, your filter will help attain this objective. Consult your pool supply dealer
for instructions regarding the proper use of chlorine, algaecide and other chemical
agents required for sparkling clear water.
• Keeppoolchemicalsawayfromchildren.
• Donotreplenishchemicalsinpoolwhilepoolisoccupied.Skinoreyeirritationscould
occur.
• DailypHcheckingandchemicaltreatmentofthewaterisveryimportantandcannotbe
overemphasized.MaintenanceofproperpHlevelsarerequiredwhenfillingthepoolas
well as during the season. Consult your local swimming pool supply store for
instructions.
• Theseason'sfirstfillingofthepoolmayhavebrackishwaterrequiringextrawater
additivesandextrafilteringtime.DonotallowswimminginpooluntilthepHlevelis
balanced. Consult your local swimming pool supply store for instructions.
• Chlorinatedwatermaydamagelawns,gardensorshrubberyaschildrenplayinthepool
and splash water outside the pool. Lawn areas underneath the pool liner will be
destroyed.Notethatsometypesofgrassmaygrowthroughtheliner.
• Filterruntimedependsonpoolsize,weatherandusagelevel.Experimentwithvarious
run times so as to produce clean clear water.
MAINTENANCE
MAINTENANCE (continued)
The3-WayTestStripscantestthe“FreeChlorine”,“pH”,and“TotalAlkalinity”levelsatthe
same time. We recommend that you test the water chemistry weekly, and maintain the
chlorine concentration at 0.5-3 ppm.
Directions and Use
1. Dip the entire strip into the water and remove immediately.
2. Holdthestriplevelfor15seconds.Donotshakeexcesswaterfromthestrip.
3. Nowcomparethestrippadtothecolorchartonthepackaginglabel.Ifnecessary,
adjust the chemical level in the pool water. It is very important, to use the proper
techniquewhentestingthewater'schemicallevel.Readandfollowthewrittenstrip
instructions carefully.
INTEX
®
3-WAY TEST STRIPS (PACKED WITH THE PRODUCT)
The Copper Ion Test Strips can be used to test the copper ion concentration in the water.
Directions and Use
1. Dip the entire strip into the water for 3 seconds, then remove it.
2. Holdthestriplevelfor15seconds.Donotshakeexcesswaterfromthestrip.
3. Nowcomparethecopperionstrippadtothecolorchartonthepackaginglabel.
INTEX
®
COPPER ION TEST STRIPS (PACKED WITH THE PRODUCT)
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 31
English
POOL MAINTENANCE & CHEMICAL DEFINITIONS
MAINTENANCE
Free Chlorine - Is the chlorine residual present in pool water.
Combined Chlorine - Is formed by the reaction of free chlorine with ammonia
wastes.
Result if too high - Sharp chlorinous odor, eye irritation.
pH
- A value that indicates how acidic or basic a solution is.
Result if too low - Corroded metals, eye & skin irritation,
destruction of total alkalinity.
Result if too high - Scale formation, cloudy water, shorter
filter runs, eye & skin irritation, poor
chlorine efficiency.
Total Alkalinity - Indicatesthedegreeofthewater'sresistancetochange
inpH.ItdeterminesthespeedandeaseofpHchange,
soalwaysadjusttotalalkalinitybeforeadjustingthepH
level.
Result if too low - Corroded metals, eye & skin irritation.
LowalkalinitywillcausethepHtobe
unstable. Any chemical added to the
waterwillhaveanaffectonpH.
Result if too high - Scale formation, cloudy water,
eye & skin irritation, poor chlorine
efficiency.
Calcium Hardness - Refers to the amount of calcium and magnesium
dissolved in the water.
Result if too high - Scale will form and will cause the
water to become cloudy.
Stabilizer - Stabilizers extend the life of chlorine in swimming pools.
(Cyanuric Acid)
Consult with local swimming pool dealer for water treatment.
• Donotaddpoolchemicalsdirectlytotheskimmer.Thismaydamagethecell.
•Maintainingasaltandsanitizerlevelabovetherecommendedrangecan
contribute to the corrosion of the pool equipment.
• Checktheexpirydateofthetestkitasthetestresultsmaybeinaccurateifthe
kit is used after that date.
• If,duetoheavypoolusage,itisrequiredtoincreasethesanitizerlevel,thenuse
a chemical based on trichlor, TCCA or dichloro.
Preferred Water Chemistry Reading
Minimum Ideal Maximum
Copper Ions 0 0.1 - 0.2 ppm 0.2 ppm
Free Chlorine 0 0.5 - 3.0 ppm 5.0 ppm
Combined Chlorine 0 0 ppm 0.2 ppm
pH 7.2 7.4 - 7.6 7.8
Total Alkalinity 100 ppm 100 - 140 ppm 140 ppm
Calcium Hardness 150 ppm 200 - 400 ppm 500 - 1000 ppm
Stabilizer (Cyanuric Acid) 10 ppm 20 - 40 ppm 50 ppm
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 32
English
MAINTENANCE
1. Beforeemptyingyourpoolforlongtermstorage,orrelocation,besurethe
water is directed towards an acceptable drain water receptacle away from the
house. Check local regulations for specific directions regarding disposal of
swimming pool water.
2. Switch off the unit, and disconnect power cord from electrical outlet.
3. When the pool is empty, disconnect all hoses from pump and plunger valves
and remove the strainers/plunger valves from the pool wall.
4. In a counter clockwise motion unscrew the drain valve cap (9) from the drain
valve to thoroughly drain the tank. The drain valve is located at the bottom of
the filter tank.
5. Disassemble the pump motor from the tank base.
6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.
7. Coat the following o-rings and washers with petroleum jelly for long term
storage:
• L-shapeo-ring(27).
• o-ringA(18).
• PumphoseO-rings(29).
• Strainervalveassemblystepwashers(30).
• Flatstrainerrubberwashers(32).
8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve
top“N”position.Thisallowsthewatertodrainfromthevalve.Leavethe6-way
valve in this inactive position.
9.
It is best to place all dry pieces and pump motor in the original packaging for
storage. To avoid condensation or corrosion problem, do not cover or wrap pump
motor with plastic bags.
10. Storethepumpmotorandaccessoriesinadryplace.Thestorage's
temperature should be controlled, between 0 degrees Celsius (32 degrees
Fahrenheit)and40degreesCelsius(104degreesFahrenheit).
LONG TERM STORAGE & WINTERIZATION
CAUTION
Allowing the water to freeze will damage the sand filter and void the warranty.
If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is
non-toxic and will not damage plastic system components; other anti-freezes
are highly toxic and may damage plastic components in the system.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 33
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
English
• Linecordmustbepluggedintoa3wire
outletthatisprotectedbyaClassAGround
FaultCircuitInterrupter,orRCD.
• Resetcircuitbreaker.Ifcircuitbreakertrips
repeatedly, your electrical system may have
a defect. Turn off circuit breaker and call an
electrician to correct the problem.
• Letthemotorcooldownandrestartagain.
• See“Saltwatersystemoperation”.
• See“Cyanuricacidtable”.
• AdjustthechlorineandpHlevel.Consultyour
local swimming pool supply stores.
• Loadwithfiltersand,see“sandloading
instructions”.
• Setvalveto“FILTER”position.
• Operatethefilterforlongerperiods.
• UseIntexpoolvacuumtocleanbottomofpool.
• Cleanthebasket.
• Clearanyobstructionsintheintakehosebydischargingit
inside pool wall.
• Tightenhosenuts,checkhosesfordamage,checkpoolwater
level.
• Cleanthepre-filteringbasketmoreoften.
• Backwashfilter.
• Installthenozzleattheupperpositionofthepoolinlet,and
the strainer at the lower position of the pool outlet.
• Removeabout1”ofsandifnecessary.
• Removeanypoolvacuumingdeviceattachedtothesystem
line.
• Turnoffpump,clearanydebrisorobstructionintheoutlet,
remove all air from the filter pump and turn pump on again.
• Turnoffpump,ifwaterleakingfromthevacuumrelease
valve, then release valve needs to be replaced. Contact
Intex Service Center immediately to order replacement.
Youmaycoverreleasevalvewiththecaptemporarilyifyou
ensure that the strainer cover / strainer grid is installed and
you Do Not run the pump while pool is occupied.
• Fillpooltocorrectwaterlevel.
• Cleanstrainerscreensatpoolinlet.
• Tightenhosenuts,checkhosefor
damage.
• ContactIntexservicecenter.
•
Remove 6-way valve cover and ensure the
o-ring is in place.
Clean sand tank o-ring with garden hose water.
Tighten the clamp with wrench supplied.
Contact Intex service center.
• Tighten/reinstallhosenut.
• Ensureo-ring/L-shapeo-ringisinplace
and not damaged.
• Clearanyobstructionsintheintakeby
unscrewing it from the 6-way valve.
• ContactIntexservicecenter.
• UseonlyNo.20silicasandwithparticlesize
range 0.45 to 0.85 mm (0.018 to 0.033 inches)
and a Uniformity Coefficient less than 1.75.
• Changesand.
FILTERMOTOR
FAILSTOSTART
FILTERDOESN’T
CLEANPOOL
FILTERDOESN’T
PUMP WATER OR
FLOWISVERY
SLOW
PUMPDOESN’T
WORK
6-WAYVALVE/
COVERLEAKING
HOSELEAKING
PRESSUREGAUGE
DOESN’TWORK
SANDISFLOWING
BACKINTOTHE
POOL
• Thepowercordisloose.
• TheGFCI/RCDcircuitbreaker
is tripped.
• Motortoohotandoverload
protection is shut off.
• Stand-by/powersavingmode.
• Withoutcyanuricacid.
• ImproperchlorineorpHlevels.
• Nofilteringmediaintank.
• Wrong6-wayvalvesetting
position.
• Excessivelydirtypool.
• Dirtorsandon poolfloor.
• Thebasketisrestrictingthewater
flow.
• Cloggedinletordischarge.
• Anairleakontheintakeline.
• Excessivelydirtypool.
• Sandmediacloggedwithdirt.
• Nozzleandstrainer
connections are reversed.
• Crustingorcakingonthe
filtering sand surface.
• Poolvacuumingdevice
attached to the system.
• Thevacuumreleasevalveonthe
plunger valve is activated.
• Thevacuumreleasevalveonthe
plunger valve is leaking.
• Lowwaterlevel.
• Strainerscreencloggedup.
• Anairleakontheintakehose.
• Faultymotorortheimpeller
is jammed.
• Sandtanko-ringmissing.
• Sandtanko-ringdirty.
• Flangeclampnottight.
• 6-wayvalvedamage.
• Hosenutnotsecurelytight.
• Hoseconnectionfitting
o-ring/L-shape o-ring missing.
• Cloggedinletofthepressure
gauge.
• Pressuregaugedamage.
• Sandistoosmall.
• Sandbediscalcified.
TROUBLE CAUSE SOLUTION
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 37
SAFETY GUIDELINES
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demandconstantsupervision.Acompetentadultshouldbeappointedas
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learntoswim.
• TakethetimetolearnCPRandfirstaid.
• Instructanyonewhoissupervisingpoolusersaboutpotentialpool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instructallpoolusers,includingchildrenwhattodoincaseofan
emergency.
• Alwaysusecommonsenseandgoodjudgementwhenenjoyingany
water activity.
• Supervise,supervise,supervise.
For additional information on safety, please visit
•TheAssociationofPoolandSpaProfessionals:TheSensibleWay
to Enjoy Your Aboveground/Onground Swimming Pool
www.nspi.org
• AmericanAcademyofPediatrics:PoolSafetyforChildren
www.aap.org
• RedCrosswww.redcross.org
• SafeKidswww.safekids.org
• HomeSafetyCouncil:SafetyGuidewww.homesafetycouncil.org
• ToyIndustryAssociation:ToySafetywww.toy-tia.org
English
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 38
English
LIMITED WARRANTY
YourSandFilterPump&Saltwatersystemhasbeenmanufacturedusingthehighestquality
materials and workmanship. All Intex products have been inspected and found free of defects
priortoleavingthefactory.ThisLimitedWarrantyappliesonlytotheSandFilterPump&
Saltwater system and accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initialretailpurchase.Keepyouroriginalsalesreceiptwiththismanual,asproofofpurchase
will be required and must accompany warranty claims or the Limited Warranty is invalid.
SandFilterPump&SaltwatersystemWarranty2Years
TitaniumElectrodeWarranty–1Year
Hoses,PlungerValves&FittingsWarranty–180days 
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim. If the Service Center directs you
to return the product, please carefully package the product and send with shipping and
insurance prepaid to the Service Center. Upon receipt of the returned product, the Intex
Service Center will inspect the item and determine the validity of the claim. If the provisions
of this warranty cover the item, the item will be repaired or replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought before
an informal dispute settlement board and unless and until the provisions of these paragraphs
are carried forth, no civil action may be instituted. The methods and procedures of this
settlementboardshallbesubjecttotherulesandregulationssetforthbytheFederalTrade
Commission(F.T.C.).IMPLIEDWARRANTIESARELIMITEDTOTHETERMSOFTHIS
WARRANTYANDINNOEVENTSHALLINTEX,THEIRAUTHORIZEDAGENTSOR
EMPLOYEESBELIABLETOTHEBUYERORANYOTHERPARTYFORDIRECTOR
CONSEQUENTIALDAMAGESORLIABILITIES.Somestates,orjurisdictionsdonotallow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This Limited Warranty does not apply if products are subject to negligence, abnormal use
or operation, accident, improper operation, improper voltage or current contrary to operating
instructions, or to damage by circumstances beyond Intex’s control, including but not limited
to, ordinary wear and tear and damage caused by exposure to fire, flood, freezing, rain, or
other external environmental forces. This Limited Warranty applies only to those parts and
components sold by Intex. The Limited Warranty does not cover unauthorized alterations,
repairs or disassembly by anyone other than Intex Service Center personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN
OR REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex CS20110 Krystal Clear bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex CS20110 Krystal Clear in de taal/talen: Engels als bijlage per email.

De handleiding is 12,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info