752348
37
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
English
Krystal Clear
TM
Sand Filter Pump
16” (410mm) & Saltwater System
Model CS20110
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves the
right to change specifications and appearance, which may result in
updates to the instruction manual, without notice.
OWNER’S MANUAL
For illustrative purposes only.
159-***-R0-1307
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 2
English
TABLE OF CONTENTS
Warnings.......................................................................... 3
Parts List & References.................................................. 4-8
Setup Instructions ......................................................... 9-16
Product Specifications................................................... 11
Operating Instructions .................................................. 17-21
LED Code Chart.............................................................. 22
Salt & Pool Water Volumes............................................ 23
Intex Pools Salt Table...................................................... 24
Intex Pools Cyanuric Acid Table.................................... 25
Intex Pools Operating Time Table ................................. 26
Non-Intex Pools Salt Table.............................................. 27
Non-Intex Pools Cyanuric Acid Table............................ 27
Non-Intex Pools Operating Time Table.......................... 27
Maintenance.................................................................... 28-32
Long Term Storage.......................................................... 32
Troubleshooting Guide................................................... 33-35
Common Pool Problems................................................. 36
General Aquatic Safety................................................... 37
Limited Warranty............................................................. 38
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 3
English
SAFETY RULES
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
Children must stay away from this product and electrical cord(s).
Assembly and disassembly by adults only.
Risk of electric shock. Connect only to a grounding type receptacle, this product
is provided with a ground-fault circuit interrupter. If replacement of the plug or cord
is needed, use only identical replacement parts.
Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
•Theunitisprovidedwithaground-faultcircuitinterrupter(GFCI).TotesttheGFCI,
push the test button. TheGFCIshouldinterruptpower.Push the reset button,
powershouldberestored.IftheGFCIfailstooperateinthismanner.TheGFCIis
defective.IftheGFCIinterruptspowertothepumpwithoutthetestbuttonbeing
pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
To reduce the risk of electric shock, replace damaged cord immediately. Use a
qualified electrician to replace the cord.
To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
Donotuseanapplianceleakagecurrentinterrupter(ALCI)inplaceofaGFCI
since the ALCI will not protect people.
•Positionthisproductawayfrompool,soastopreventchildrenfromclimbingonit
and access the pool.
Do not operate this product when pool is occupied.
To reduce the risk of entrapment hazard, never enter the pool if suction strainer
component is loose, broken, cracked, damaged or missing. Replace loose, broken,
damaged, cracked or missing suction strainer components immediately.
•Neverplayorswimnearsuctionfittings.Yourbodyorhairmaybetrappedcausing
permanent injury or drowning.
•Topreventequipmentdamageandriskofinjury,alwaysturnpumpoffbefore
changing the filter control valve position.
•Neveroperatethisproductabovethemaximumworkingpressurestatedonthe
filter tank.
•HazardousPressure.Impropertankvalvecoverassemblycouldcausethevalve
cover to blow off and cause serious injury, property damage or death.
•Thisproductisintendedtobeusedonlyforthepurposesdescribedinthemanual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
This product is for use with storable pools only. Do not use with permanently-installed pools.
A storable pool is constructed so that it is capable of being readily disassembled for storage
and reassembled to its original integrity. A permanently-installed pool is constructed in or on
the ground or in a building such that it cannot be readily disassembled for storage.
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
CAUTION
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 4
English
PARTS LIST
PARTS LIST
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
7
1
9
45
2
6
3
8
10 11 12
13 14 15
16 17 18
19 20 21
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 5
English
PARTS LIST (continued)
PARTS LIST
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
22 2423
34 35 36
31 32 33
28 29 30
25 26 27
37
40
38 39
41
Optional
Optional Optional
42
51 52
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 6
English
PARTS REFERENCE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
1
5
9
10 11
21
2
13 14
20 19
3
6
7
4
12
15
16
17
18
8
22
23
24
25
26
27
41
18
50
43
47
44
45
49
48
46
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 7
English
NOTE:Drawingsforillustrationpurposeonly.Actualproductmayvary.Nottoscale.
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
PARTS REFERENCE
28
29
30 31 32 33 34
28
29
30 35 36 37
28
29
30 35 36 38
28
29
30 31 32 33 38
51
51
51
51
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 8
English
When ordering parts, be sure to quote the model number and part numbers.
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
PARTS REFERENCE
REF. NO. DESCRIPTION QTY. SPARE PART NO.
1PRESSUREGAUGE 1 11224
2 6-WAYVALVESET 1 11496
3 DRAINOUTLETCOVER 1 11131
4 TANKO-RING 1 11379
5 SCREW 2 11381
6 CLAMP 1 11380
7SANDSHIELD 1 11382
8CENTERPIPEHUB 1 11495
9DRAINVALVECAP 1 11456
10 DRAINVALVEO-RING 1 11385
11 LATERAL 10 11384
12 HOSEWITHNUTS 2 11009
13 SANDFILTERINTERCONNECTINGHOSE 1 11536
14 LEAFTRAPNUT 1 11479
15 LEAFTRAPO-RING 1 11232
16 BASKET 1 11260
17 FILTERHOUSINGNUT 1 11261
18 L-SHAPEO-RING 4 11228
19 SEDIMENTRELEASEVALVE 1 10460
20 VALVEO-RING 1 10264
21 FLOWSENSOR 1 11460
22 ELECTROLYTICCELL 1 11372
23 TITANIUMELECTRODE 1 11374
24 COPPER ELECTRODE 1 11234
25 PRE-FILTERASSEMBLY 1 11371
26 PUMPMOTOR&CONTROL 1 11377
27 L-SHAPEO-RING 1 11439
28
PLUNGERVALVE(HOSEO-RING&STEPWASHERINCLUDED)
2 10747E
29 HOSEO-RING 2 10262
30 STEPWASHER 2 10745
31 STRAINERNUT 2 10256
32 FLATSTRAINERRUBBERWASHER 2 10255
33
THREADEDSTRAINERCONNECTOR
2 10744
34 ADJUSTABLEPOOLINLETNOZZLE 1 11074
35 ADAPTORB 2 10722
36 STRAINERCONNECTOR(OPTIONAL) 2 11070
37 POOLINLETNOZZLE(OPTIONAL) 1 11071
38 STRAINERGRID(OPTIONAL) 1 11072
39 CHLORINETESTSTRIPS 1 19635
40 COPPER TEST STRIPS 1 11254
41 LEAFTRAPCOVER 1 11480
42 STRAINERGRID 1 10253
43 ELECTROLYTICCELLNUT 1 11432
44 COPPERELECTRODEO-RING 1 11440
45 COPPERELECTRODEHOUSING 1 11441
46 SANDFILTERPUMPMOTORINLETO-RING 2 11457
47 COPPERELECTRODENUT 1 11488
48 16"SANDFILTERPUMPANDCOMBOTANK 1 11497
49 16"SANDFILTERPUMPTANKBASE 1 11514
50 O-RINGONTITANIUMPLATES 1 11515
51 VACUUMRELEASEVALVE 2 11437
52 VACUUMRELEASEVALVECAP 2 11576
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS Page 9
English
SETUP INSTRUCTIONS
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. If your pool has an inflatable top ring, install the strainer, nozzle
and plunger valve before inflating the pool liner top ring. The part numbers
here onward refer to the parts depicted in the Parts List section of this
manual. To install, do the following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (33) (see drawing 1).
Becarefulnottolosethesteprubber
washer (30). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (31) from the threaded
connector (33). Leave the flat washer (32)
on the connector (33).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
Fromtheinsideofthepoollinerinsertthe
connector (33) into one of the pre-cut holes
with the washer remaining on the
connector to be placed against the inside
of the liner wall.
4. Beforeassembly,lubricatethethreadswith
a petroleum jelly. With the flat side of the
strainer nut (31) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (31) back onto the threaded
connector (33) (see drawing 2).
5. Fingertightenthestrainernut(31) onto the
threaded connector (33).
6. Grasptheplungervalveassembly.Make
sure the step washer (30) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (33) (see drawing 3).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during filling
of the pool (see drawing 4.1).
9. NOTE: Nevercoverthevacuumrelease
valve (51) unless it is damaged or leaking.
Replace the vacuum release valve
immediately.
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
1
2
3
32 33
INSIDE
LINER WALL
31
4.2
2
1
1
2
4.1
INSIDE
LINER WALL
30
WATER
FLOW
POOL
51
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 10
English
SETUP INSTRUCTIONS
POOL INLET - NOZZLE & PLUNGER VALVE SETUP
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (33) (see drawing 5).
Becarefulnottolosethesteprubber
washer (30). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut (31) from the threaded
connector (33). Leave the flat washer (32)
on the connector (33).
3. Install the nozzle and plunger valve at the
upper position of pool inlet. Fromtheinside
of the pool liner insert the connector (33)
into one of the pre-cut holes with the
washer remaining on the connector to be
placed against the inside of the liner wall.
4. Beforeassembly,lubricatethethreadswith
a petroleum jelly. With the flat side of the
strainer nut (31) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut (31) back onto the threaded
connector (33) (see drawing 6).
5. Fingertightentheadjustablepoolinlet
nozzle (34) and the strainer nut (31) onto
the threaded connector (33).
6. Grasptheplungervalveassembly.Make
sure the step washer (30) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (33) (see drawing 7).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during filling
of the pool (see drawing 8).
9. NOTE: Nevercoverthevacuumrelease
valve (51) unless it is damaged or leaking.
Replace the vacuum release valve
immediately.
10. Adjust the direction of nozzle head pointing
away from the pool outlet for a better
circulation result (see drawing 9).
11. The pool liner is now ready to fill with
water. Consult the above-ground-pool
owner’s manual for filling instructions.
9
5
2
1
7
1
2
8
INSIDE
LINER WALL
6
32 33 34
INSIDE
LINER WALL
31
WATER
FLOW
POOL
51
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 11
English
PRODUCT SPECS & SETUP INSTRUCTIONS
PRODUCT SPECIFICATIONS
SETUP INSTRUCTIONS
Power: 110-120VoltAC
Amperage: SaltwaterSystem-1.1A;FilterPump-6A
Wattage: SaltwaterSystem-120W;FilterPump-650W
Ideal Salt Level: 3000 ppm (parts per million)
Maximum Sanitizer Output/hour: 11 grams/hour
Copper Ionizer Output Current: 175mA
Maximum working pressure: 3.5 bar (50 psi)
Effective filtering area: 0.13 m2 (1.44 ft2)
MaximumFlowRate: 10030 liters/hour (2650 gallons/hour)
Recommended filtering media:
No.20silicasandorglasssand.Particlesize
(Notincluded) range0.45to0.85mm(0.018to0.033inches).
Uniformity Coefficient less than 1.75.
Recommended filtering media quantity:
No.20silicasand
45Kg(100Lbs)
or glass sand
32Kg(70Lbs).
Limited Warranty: see “Limited Warranty”
The sand filter removes suspended particles and sanitize your pool. Pool
chemistry is a specialized area and you should consult your local pool
service specialist for details.
TOOLS REQUIRED: One (1) Phillips screwdriver
Pump location and mounting:
• Thesystemmustbeinstalledonasolidlevelandvibration-freebase.
• Providealocationprotectedfromtheweather,moisture,floodingand
freezing temperature.
• Provideadequateaccess,spaceandlightingforroutinemaintenance.
• Pumpmotorrequiresfreecirculationofairforcooling.Donotinstall
the pump in a damp or non-ventilated location.
A team of 2 or more people is recommended for setting up this product.
Motor pre-filtering assembly setup:
1. Remove the sand filter and its accessories
from the packaging carefully and inspect for
any visible damage. If parts are damaged
contact your local service center listed at the
back of this owner’s manual.
2. In a counter-clockwise motion unscrew the leaf
trap cover (14) from the pre-filter housing.
Take out the basket (16) and filter housing
nut (17) (see drawing 10).
3.
Connect the pre-filter housing to the motor
waterinlet.Note: Align the connector in the
pre-filter housing with the water inlet on the
motor (see drawing 11).
10
11
14
17
16
41
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 12
English
4. In a clockwise motion screw filter housing nut (17) onto the motor water inlet
(See drawings 12.1 & 12.2).
5. Replace the basket (16) and leaf trap cover (14) back to the pre-filter housing
(See drawings 13.1 & 13.2).
SETUP INSTRUCTIONS (continued)
SETUP INSTRUCTIONS
Sand tank installation:
1. Place the tank support base at the selected location.
2. Place the tank on the tank support base (See drawing 14.1).
3. Connect the motor pre-filtering assembly unit to the tank support base (See
drawing 14.2). NOTE: Ensure the pre-filter housing water inlet hose connection
is facing towards the pool.
IMPORTANT: Some countries, especially in the European community,
require the product to be secured to the ground or to a base in a
permanent upright position. Check your local authorities to determine if
there is a regulation in your area regarding above-the-ground swimming
pool filter-pumps. If yes, then the product can be mounted to a platform
using the two holes located in the base. See drawing 14.3.
The product can be mounted on a cement base or onto a wooden
plat form to prevent accidental falling over.
• Themountingholesare6.4mmindiameterandspaced177.4mm
apart.
• Usetwoboltsandlocknutswithamaximumof6.4mmindiameter.
13.1 13.2
14.1 14.2
177.4 mm
14.3
16
14
12.2
12.1
17 17
41
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 13
English
SETUP INSTRUCTIONS (continued)
SETUP INSTRUCTIONS
Sand loading:
IMPORTANT: Use No. 20 silica sand or glass sand with particle size range
0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less
than 1.75.
NOTE: Before loading the tank with sand, ensure the center pipe hub
assembly is securely in place at the bottom of the tank, and vertically
centered inside the tank.
1. Place the sand shield (7) over the top of the center pipe. Pour the sand into the
tank at a slow rate. (see drawing 15).
2. Fillthetankapproximatelyhalfway,removethesandshield (7). (see
drawing 16).
3. Evenly distribute the sand inside the tank, then fill the tank with some water to
provide a cushioning effect when the remaining sand is poured in. This
prevents the center pipe hub (8) from excessive shock (see drawing 17).
Place the sand shield (7) back and continue to pour the sand into the tank.
4. Sandshallbefilledbetweenthe“MAX”and“MIN”markedgaugeonthecenter
pipe. Evenly spread and level out the sand by hand (see drawings 17 & 18).
5. Remove the sand shield (7).
6. Wash away all sand around the top edge of the tank.
15 16
77
MAX
MIN
17
MAX
MIN
MAX
MIN
18
8
8
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 14
English
6-way valve installation:
1. Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding
underneath the 6-way valve fits securely into the center pipe hub (8) top opening (see
drawing 19).
IMPORTANT: There are three hose connection ports on the 6-way valve, ensure
the outlet connection (from filter to the pool) on the valve is facing towards the
pool, and the inlet connection (from motor to valve) is aligned with the motor
outlet (see drawing 20).
2. Remove the clamp bolt, and install the clamp around the tank and 6-way valve flanges,
then replace the clamp bolt and use a phillips screwdriver (not included) to tighten it.
(see drawing 21).
SETUP INSTRUCTIONS
SETUP INSTRUCTIONS (continued)
WARNING
Improper tank valve and clamp assembly could cause the valve and clamp
to blow off and cause serious injury, property damage or death.
3. Connect the sand filter interconnecting hose (13) between the 6-way valve inlet and
motor outlet, and insert the electrolytic cell (22)intothe6-wayvalveoutlet.Handtighten
them securely (see drawings 22 and 23).
22 23
4. Screw and tighten the flow sensor (21) to the electrolytic cell (22), then plug in the
electrolytic cell line cord and tighten the nut (see drawings 24 and 25).
24 25
13
21
22
22
6
19 20
WATER
INLET
WATER
OUTLET
21
8
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 15
English
SETUP INSTRUCTIONS
SAND FILTER PUMP HOSE CONNECTION SETUP
The 6-way valve has three hose connection ports.
1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose
to the lower plunger valve with the strainer. Ensure the hose nuts are securely
tighten.
2. Connect the second hose (12) between the electrolytic cell outlet and the
upper plunger valve with the inlet-nozzle. Ensure the hose nuts are securely
tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be
directed to a proper draining receptacle using a hose or pipe (not provided).
Remove the drain cap before attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.
WARNING
• Positionthisproductawayfromthepool,soastopreventchildrenfrom
climbing on it and accessing the pool.
6-WAY VALVE
WATER LEVEL
ADJUSTABLE
POOL INLET
NOZZLE
THREADED
STRAINER
CONNECTOR
OUTSIDE
LINER WALL
PLUNGER
VALVE
(ILLUSTRATION NOT TO SCALE)
TO
DRAIN
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 16
English
SAND FILTER PUMP HOSE CONNECTION SETUP (continued)
SETUP INSTRUCTIONS
For INTEX pool size 16' and below:
1. In a counter-clockwise motion unscrew plunger valve union from the threaded
strainer connector (25).Becarefulnottolosethesteprubberwasher(22).
2. Grasptheplungervalveassembly.Makesurethestepwasher(22) is in place.
ConnectadaptorB(35) to plunger valve union.
3. Remove wall plug and then insert the strainer (28 & 30) into the lower position
of protruding hose connection, and the nozzle (28 & 29) into the upper position
ofprotrudinghoseconnection.AdaptorB(35) fits over the strainer
connection (28) inserted into the connection. Tighten securely.
4. Remove the drain valve (3) from the 6-way valve outlet and connect the hose
to the outlet.
For NON-INTEX pool:
1. Connect the hose (12) to the pool inlet/outlet connection with a large hose
clamp. Tighten securely. Remove the drain valve (3) from the 6-way valve
outlet and connect the hose to the outlet.
POOL
LARGE HOSE
CLAMP
POOL
12
3
28 & 29
3
28 & 30
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 17
English
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
• Riskofelectricshock.Connectthisproductonlytoagroundingtype
receptacle protected by a ground-fault circuit interrupter (GFCI) or
residual current device (RCD). Contact a qualified electrician if you cannot
verify that the receptacle is protected by a GFCI/RCD. Use a qualified
electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
Do not use a portable residual current device (PRCD).
To reduce the risk of electric shock, do not use extension cords, timers,
plug adaptors or converter plugs to connect unit to electric supply;
provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water
or when your hands are wet.
• Neveroperatethisproductabovethemaximumworkingpressurestated
on the filter tank.
• Alwaysswitchoffpumpbeforechangingthe6-wayvalveposition.
• Operatingthisproductwithoutwaterflowingthroughthesystemcan
cause a build up of hazardous pressure which can result in an explosive
situation, serious injury, property damage or death.
• Nevertestthispumpwithcompressedair.Neveroperatethesystemwith
water temperature above 35° C (95° F).
Valve Position Function Water Flow Direction
FILTER
(see drawing 26)
Normalfiltrationandregular
vacuuming of pool
Frompumpthroughfiltermedia
to pool
BACKWASH
(see drawing 27)
Reverses water flow to clean
filter media
Frompumpthroughfiltermedia
to valve waste/drain outlet
RINSE
(see drawing 28)
Forinitialstartupcleaningofthesand,and
leveling the sand bed after backwashing
Frompumpthroughfiltermedia
to valve waste/drain outlet
WASTE
(see drawing 29)
Forvacuumingdirectlytowaste,
lowering pool level or to drain the pool
Frompumptovalvewaste/drain
outlet bypassing the filter media
RECIRCULATE
(see drawing 30)
Forcirculatingwaterbacktopool
without going through the filter media
Frompumpthroughvalveto
pool bypassing the filter media
CLOSED
(see drawing 31)
Shuts off all flow to filter and pool
“Do not use this setting with pump running”
6-way valve positions and function:
WARNING
RETLIF
ESNI
R
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
26
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
27
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
28
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 18
English
Initial startup and operation:
Before operating, be sure that:
• Allthehoseshavebeenconnectedandtightenedsecurely,andcorrectamount
of filter sand have been loaded.
• Theentiresystemisconnectedtoagroundingtypereceptacleprotectedbya
ground-faultcircuitinterrupter(GFCI)orresidualcurrentdevice(RCD).
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should never be
on when the valve is in the closed position. If the pump is operated with
the valve closed, and explosive situation could exist.
1. Turn both plunger valve handles fully counter-clockwise until they stop. This
opens the valves to allow water to flow into the sand filter pump.
NOTE: The plunger valve is equipped with a vacuum release valve that will
automatically activate to minimize the suction at the pool outlet if the outlet is
blocked. This is an additional safety feature to prevent suction entrapment.
The vacuum release valve will reset once the blockage is removed and the
pump is switched off. To restart the system the air must be removed from the
filter pump per previous step.
2. Ensure the drain/waste outlet on the 6-way valve is not covered and directed to
a proper draining receptacle.
3. Ensure the pump is off, depress the 6-way
valve and turn it to the “BACKWASH
position (see drawings 27 & 32).
IMPORTANT: To prevent damage to the
6-way valve, always depress the valve
handle before turning. Always switch off
pump before changing the 6-way valve
position.
4. Switch on the pump (see drawing 33). Water
is circulating backward through the sand
mediaandtowaste/drainoutlet.Backwash
until a clear flow of water is observed in the
waste/drain outlet or through the drain sediment
window.
NOTE: The initial backwash of the filter is
recommended to remove any impurities or fine
sand particles in the sand media.
32
1
2
33
OFF
ON
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
29
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
30
RETLIF
ESNIR
ETALUCRICER
ES
O
LC
ETSAW
ESN
IR
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ETSAW
R
ETLIF
ESNIR
ER
HSAWKCAB
ESOLC
ETSAW
RETLIF
ESNIR
ETALUCRICER
HSAWKCAB
ESOLC
R
ETLIF
ETALUCRICER
HSAWKCAB
ESOLC
ETSAW
B
31
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 19
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS (continued)
English
5. Switchoffthepump,changethe6-wayvalveto“RINSE”position(see
drawing 28).
6. Switch on the pump and run the pump for about one minute to level out the
sand bed after backwashing the sand media.
7. Switchoffthepump,changethe6-wayvalveto“FILTER”position(see
drawing 26).
8. Switch on the pump. The system is now operating in the normal filtering mode.
Run the pump until the desired pool water clearance is obtained and no more
than 12 hours per day.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash
frequently due to unusual heavy dirt present in the water and sand. After that,
as the filter removes dirt and impurities from the pool water, the accumulated
dirt in the sand media will cause the pressure to rise and the flow to diminish. If
there is no vacuuming device attached to the system and the pressure gauge
reading is in the yellow zone it is time to backwash the sand media, see
“BACKWASH”under“initialstartupandoperation”section.
Vacuumingdevice(i.e.Intexautopoolcleaner)attachedtothesystemmay
also cause the flow to diminish and the pressure to rise. Remove any
vacuuming device from the system and check if the pressure gauge reading has
dropped from the yellow zone to the green zone.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassB
digitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedto
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 20
English
SALTWATER SYSTEM OPERATION
OPERATING INSTRUCTIONS
1. Start up the unit:
Plug the power cord into the electrical outlet and test
theGFCI/RCD(circuitbreaker).Switchontheunit.
WiththeFilterPumpturned“ON”andoperating.
Flashingcode“00”appearsontheelectroniccontrol
station’s LED, indicating that the unit is ready to be
programmed.
2. Set operating hours for Saltwater System:
With code “00” flashing, press button to
set the desired operating hours. See the
“Operating Time Table” for the required
operating hours related to each pool size.
Pressing will increase the time from 01
to 12 hours maximum. If you have selected
too many hours keep pressing to repeat
the cycle. The built-in timer will now activate
your Saltwater System, at the same time
each day, for the number of hours you have set.
NOTE: The Saltwater System will not operate if the filter pump is not operating.
3. Lock keypad controls:
With the desired hour value showing, press button until
youheara“beep”.Thegreen“WORKING”indicatoronthe
control panel will light up within a few seconds to indicate that
the saltwater system has started sanitizer production. Locking
the control buttons into this setting prevents unauthorized
changing of the operating cycle.
NOTE: If you forget to lock the keypad controls, the system
will automatically lock it and start working 1 minute later.
4. Readjust operating time if necessary:
The operating hours can be re-adjusted if necessary.
Press button until you hear a “beep” to unlock the
keypad and the current programmed time will flash.
Repeat steps 2 to 3.
5. Test the copper concentration in the
pool water.
The Saltwater System recommends a copper
level of 0.1 to 0.2 ppm.
This is easily tested by the copper ion test
strips provided. If the test result is
0.1~0.2ppm, go directly to step 7.
OK
0
Copper (ppm)
0.1 0.2 0.5 0.9 1.3
(1 to 12 hours max per cycle)
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 21
English
SALTWATER SYSTEM OPERATION (continued)
OPERATING INSTRUCTIONS
6. Boost cycle
Ifthetestresultisbelow0.1ppm,pressandhold“BOOST”
button for 5 seconds until the indicator lights up and the
LED display display “80”. This indicates that the saltwater
system has started copper ion and more chlorine sanitizer
production.Youcanpressandholdthe“BOOST”buttonfor
another 5 seconds until the indicator is off, which will cancel
theBoostcycle.
Note: Once the system has started copper ion and more
chlorine sanitizer production, the boost button can’t be re-set until the power
switch is off.
The boost operating hours is 8 times the amount of time programmed into the
system, i.e. if your saltwater system operating time is 2 hours, the boost procedure
will run 8 x 2 = 16 hours. After boost procedure has been completed, the system
will automatically switch to the normal working mode.
Afteraheavyrainorifthepoolisdirty,pressthe“BOOST”buttontoshockthe
pool again.
7. Test pool water regularly:
Once the copper level appears to be balanced, test the pool water every week
to maintain the proper sanitizer level.
It’s very important that the free chlorine is between 0.5-3 ppm and copper
ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1
ppm, repeat step 6.
NOTE:AHighcopperionconcentrationmaycauseblondehairtoexhibita
green hair. To prevent this, wear a swimming cap during swimming, and wash
hair with special shampoo after using the pool.
See“TroubleshootingGuide”.
8. Stand-by/power saving mode:
When the cycle ends, the green “SLEEP” indicator on the
control panel lights up and the LED display flashes “93”.
ThesystemisnowinStand-Bymode.Afterawhile,it
shuts down and sets itself in a Power Saving mode. The
system will automatically turn itself back on in 24 hours,
starting its daily cycle of chlorine production.
The “SLEEP” indicator stays on, while the system is in the
Power Saving mode. The LED display however, goes blank
after 1 hour. Press any button ( or ) to view the last LED
code.
9. Running the pump alone without the Saltwater System:
To run the pump alone without the Saltwater System function,
press and hold both ( ) and ( ) buttons for 5 seconds
untilyouheara“beep”andtheLEDdisplayshows“FP”.
The pump is now operating alone. To stop the pump,
manuallyturntheswitchOFF.NOTE: The pump cannot
be operated alone under an automatic timer mode.
IMPORTANT: To keep the initial automatic operating cycle
settingoftheSaltwaterSystem,turntheswitchON,the
LEDdisplayshows“FP”,thenunlockandlockthekeypad
controls again, see previous steps 2 and 3. The LED display shows
the initial input hours and the Saltwater System cycle repeats again.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 22
English
LED CODE CHART
LED CODE CHART
LED Reading Definitions
FP FilterPumpWorkingMode
80 BoostMode
00 Stand-ByMode(Start-up)
01 MinimumOperatingHour(1hourremaining)
02 OperatingHours(2hoursremaining)
03 OperatingHours(3hoursremaining)
04 OperatingHours(4hoursremaining)
05 OperatingHours(5hoursremaining)
06 OperatingHours(6hoursremaining)
07 OperatingHours(7hoursremaining)
08 OperatingHours(8hoursremaining)
09 OperatingHours(9hoursremaining)
10 OperatingHours(10hoursremaining)
11 OperatingHours(11hoursremaining)
12 MaximumOperatingHours(12hoursremaining)
90 AlarmCode(LowPumpFlow/NoFlow)
91 Alarm Code (Low Salt Level)
92 AlarmCode(HighSaltLevel)
93 Stand-ByMode(OperatingProcessfinished)
“BLANK” NoPoweror“PowerSavingMode”waitingtostartnext
Saltwater System cycle.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 23
English
SALT & POOL WATER VOLUMES
SALT & POOL WATER VOLUMES
• Whichkindofsalttouse:
Use only Sodium Chloride Salts
Useonlysodiumchloride(NaCl)saltthatisatleast99.8%pure.Itisalso
acceptable to use water conditioning salt pellets (the compressed forms of
evaporatedsalt).However,itwilltakealongertimeforthemtodissolve.Do not
use iodized or yellow (yellow prussiate of soda) colored salt. Salt is added to
the pool water and the electrolytic cell uses the salt to create the sanitizer. So, the
purer the salt the better the performance of the electrolytic cell.
• OptimumSaltLevels
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million).
The optimal level is 3000 ppm.
A too low salt level will reduce the efficiency of the saltwater system and result in
low sanitizer production. A high salt level may generate a salty taste to the pool
water (this may occur at a salt level above 3500-4000ppm). Too high of a salt level
may damage the power supply and cause corrosion to pool metal fixtures and
accessories. The Salt Table page of this manual, shows the correct dosage of salt
needed. The salt in the pool is constantly recycled. Salt loss occurs only when pool
water is physically removed from the pool. Salt is not lost due to evaporation.
• AddingSalt
1. Switch on the unit, then press and hold both and button for 5 seconds,
theLEDflashes“FP”.TheunitisnowinaFilterpumpworkingmodeand
switch the filter pump on to start the water circulation.
2. KeeptheSaltwaterSystemturnedoff.
3. Determine the amount of salt to be added (see “Salt Table”).
4. Evenly spread the proper amount of salt around the inside perimeter of the
pool.
5. Avoid clogging the filter by not adding salt through the skimmer.
6. Brushthepoolbottomtospeedupthedissolvingprocess.Donotallowsaltto
pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to
thoroughly dissolve the salt.
7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System,
press button until you hear a “beep”, code “00” flashing (see “System
Operation” section steps 2 to 4) and set the saltwater pool system to desired
operating time (see “Operating Time Table”).
• RemovingSalt
If too much salt has been added, the unit will beep and display “Code 92” (see “Alarm
Codes”).Youwillneedtolowerthesaltconcentration.Theonlywaytodoso,isto
partially drain the pool and refill it with fresh water. Drain and refill
approximately20%ofthepool’swateruntilthe“Code92”disappears.
• PoolVolumeCalculation
Rectangular
Length x Width x Average Depth x 7.5 Length x Width x Average Depth
Circular
Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79
Oval
Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80
Types of Pool Gallons
(pool size in feet)
Cubic Meters
(pool size in meters)
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 24
English
INTEX POOLS SALT TABLE
This table shows the dosage of salt needed to achieve and maintain the optimal 3000 ppm salt
level.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
Salt Needed for
Startup
3.0g/L (3000ppm)
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
18' x 42" (549cm x 107cm)
4786 18115 120 55 30 15
18' x 48" (549cm x 122cm)
5455 20647 135 60 35 15
CIRCULAR
METAL
FRAME POOL
18' x 48" (549cm x 122cm)
6423 24311 160 75 40 20
21' x 52" (640cm x 132cm)
9533 36082 240 110 60 30
24' x 52" (732cm x 132cm)
12481 47241 310 140 80 35
ULTRA FRAME
POOL
18’ x 48” (549cm x 122cm)
6423 24311 160 75 40 20
18' x 52" (549cm x 132cm)
6981 26423 175 80 45 20
20’ x 48” (610cm x 122cm)
7947 30079 210 90 50 25
22’ x 52” (671cm x 132cm)
10472 39637 260 120 65 30
24’ x 52” (732cm x 132cm)
12481 47241 310 140 80 35
26 ’x 52” (792cm x 132cm)
14667 55515 365 165 90 40
SEQUOIA SPIRIT™
POOL SET
15'8" x 49" (478cm x 124cm)
4440 16805 110 50 30 15
16’8” x 49” (508cm x 124cm)
5061 19156 125 55 35 15
18'8" x 53" (569cm x 135cm)
6981 26423 175 80 45 20
OVAL FRAME
POOL
10’ x 18’ x 42” (305cm x 549cm x 107cm)
2885 10920 70 30 20 10
12' x 20' x 48" (366cm x 610cm x 122cm)
4393 16628 110 50 30 15
RECT. ULTRA
FRAME POOL
9' x 18' x 52" (274cm x 549cm x 132cm)
4545 17203 115 50 30 15
10’ x 20’ x 52” (305cm x 610cm x 132cm)
5835 22085 145 65 40 20
12' x 24' x 52" (366cm x 732cm x 132cm)
8403 31805 210 95 55 25
16' x 32' x 52" (488cm x975cm x 132cm)
14364 54368 360 165 90 40
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 25
English
INTEX POOLS CYANURIC ACID TABLE
Cyanuric acid is a chemical that reduces the loss of chlorine in water due to ultraviolet rays. To
maintain the pool water clear and clean, and to maximize the performance of the device, add
cyanuric acid to the pool. We recommend that the cyanuric acid level be maintained at
approximately 1% of the salt, i.e. 100 Lbs (45 Kgs) salt x1% = 1 Lbs (0.45 Kgs) cyanuric acid.
If the pool water is dirty, filthy or grimy, DO NOT add chlorine stabilizer (cyanuric acid) as this
will slowdown the sanitation time of the device. Under this condition you must BOOST your
pool water, refer to BOOST cycle steps. Once the pool water has been restored to clear and
clean conditions you may add cyanuric acid.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80% for
Easy Set & Oval Pool)
Cyanuric Acid Needed for
Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
18' x 42" (549cm x 107cm)
4786 18115 1.2 0.5
18' x 48" (549cm x 122cm)
5455 20647 1.4 0.6
CIRCULAR
METAL
FRAME POOL
18' x 48" (549cm x 122cm)
6423 24311 1.6 0.7
21' x 52" (640cm x 132cm)
9533 36082 2.4 1.1
24' x 52" (732cm x 132cm)
12481 47241 3.1 1.4
ULTRA FRAME
POOL
18’ x 48” (549cm x 122cm)
6423 24311 1.6 0.7
18' x 52" (549cm x 132cm)
6981 26423 1.7 0.8
20’ x 48” (610cm x 122cm)
7947 30079 2.0 0.9
22’ x 52” (671cm x 132cm)
10472 39637 2.6 1.2
24’ x 52” (732cm x 132cm)
12481 47241 3.1 1.4
26 ’x 52” (792cm x 132cm)
14667 55515 3.7 1.7
SEQUOIA SPIRIT™
POOL SET
15'8" x 49" (478cm x 124cm)
4440 16805 1.1 0.5
16’8” x 49” (508cm x 124cm)
5061 19156 1.3 0.6
18'8" x 53" (569cm x 135cm)
6981 26423 1.7 0.8
OVAL FRAME
POOL
10’ x 18’ x 42” (305cm x 549cm x 107cm)
2885 10920 0.7 0.3
12' x 20' x 48" (366cm x 610cm x 122cm)
4393 16628 1.1 0.5
RECT. ULTRA
FRAME POOL
9' x 18' x 52" (274cm x 549cm x 132cm)
4545 17203 1.1 0.5
10’ x 20’ x 52” (305cm x 610cm x 132cm)
5835 22085 1.5 0.7
12' x 24' x 52" (366cm x 732cm x 132cm)
8403 31805 2.1 1.0
16' x 32' x 52" (488cm x975cm x 132cm)
14364 54368 3.6 1.6
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 26
English
INTEX POOLS OPERATING TIME TABLE (WITH CYANURIC ACID)
Pool Size
Water Capacity (Calculated at 90%
for Frame Pool and 80% for Easy
Set & Oval Pool)
Operating Time (hours)
at different ambient/air
temperatures
(Gals) (Liters)
10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
18' x 42" (549cm x 107cm)
4786 18115 2 2 3
18' x 48" (549cm x 122cm)
5455 20647 2 3 4
CIRCULAR
METAL
FRAME POOL
18' x 48" (549cm x 122cm)
6423 24311 3 3 4
21' x 52" (640cm x 132cm)
9533 36082 4 5 6
24' x 52" (732cm x 132cm)
12481 47241 6 6 7
ULTRA FRAME
POOL
18’ x 48” (549cm x 122cm)
6423 24311 3 3 4
18' x 52" (549cm x 132cm)
6981 26423 3 4 5
20’ x 48” (610cm x 122cm)
7947 30079 4 4 5
22’ x 52” (671cm x 132cm)
10472 39637 5 5 6
24’ x 52” (732cm x 132cm)
12481 47241 6 6 7
26 ’x 52” (792cm x 132cm)
14667 55515 7 8 8
SEQUOIA SPIRIT™
POOL SET
15'8" x 49" (478cm x 124cm)
4440 16805 2 2 3
16’8” x 49” (508cm x 124cm)
5061 19156 2 3 4
18'8" x 53" (569cm x 135cm)
6981 26423 3 4 5
OVAL FRAME
POOL
10’ x 18’ x 42” (305cm x 549cm x 107cm)
2885 10920 1 1 2
12' x 20' x 48" (366cm x 610cm x 122cm)
4393 16628 2 2 3
RECT. ULTRA
FRAME POOL
9' x 18' x 52" (274cm x 549cm x 132cm)
4545 17203 2 2 3
10’ x 20’ x 52” (305cm x 610cm x 132cm)
5835 22085 3 3 4
12' x 24' x 52" (366cm x 732cm x 132cm)
8403 31805 4 4 5
16' x 32' x 52" (488cm x975cm x 132cm)
14364 54368 7 7 8
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 27
English
SALT TABLE FOR COMMON NON-INTEX POOLS
SALT CALCULATION FORMULA FOR ALL POOLS
Water Capacity Salt Needed for Startup
Salt Needed when
Low Salt Detected
(CODE “91”)
(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)
2000 7500 50 20 10 5
4000 15000 100 45 25 10
6000 22500 150 65 40 20
8000 30000 200 90 55 25
10000 37500 250 110 70 30
12000 45500 300 135 80 35
14000 53000 350 160 95 45
Salt Needed for Startup
(Lbs)
Salt Needed for Startup
(Kgs)
Salt Needed when
Low Salt Detected (Lbs)
Salt Needed when
Low Salt Detected (Kgs)
WaterCapacity(Gals)x0.025
Water Capacity (Liters) x 0.003 WaterCapacity(Gals)x0.0067 Water Capacity (Liters) x 0.0008
OPERATING TIME TABLE FOR COMMON NON-INTEX POOLS
Water Capacity
Operating Time (hours)
at different ambient/air temperatures
(Gals) (Liters) 10 - 19°C
(50 - 66°F)
20 - 28°C
(68 - 82°F)
29 - 36°C
(84 - 97°F)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
1
2
3
4
5
6
7
1
3
4
5
6
7
8
1
2
3
1
5
6
7
CYANURIC ACID TABLE FOR COMMON NON-INTEX POOLS
Water Capacity
Cyanuric Acid Needed for Startup
0.03g/L (30ppm)
(Gals) (Liters) (Lbs) (Kgs)
2000
4000
6000
8000
10000
12000
14000
7500
15000
22500
30000
37500
45500
53000
0.23
0.45
0.68
0.90
1.13
1.37
1.59
0.5
1.0
1.5
2.0
2.5
3.0
3.5
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 28
English
MAINTENANCE
MOTOR PRE-FILTER CLEANING AND MAINTENANCE
1. Make sure the filter pump is switched off, then disconnect the power cord from
the electrical outlet.
2. Turn both plunger valve handles fully clockwise until they stop. This closes the
valve, prevents the water from flowing out of the pool.
3. Release the pressure first by opening the
sediment release valve (19) located
on the lower side of the pre-filter housing
(see drawing 34).
4. In a counter-clockwise motion unscrew the
leaf trap cover (14), then remove the
basket (16) and leaf trap o-ring (15) from the
pre-filter housing (see drawing 35).
5. Empty and flush the basket using a garden
hose, may use a plastic brush to remove
deposits from the basket. Do not use metal
brush.
6. Clean and rinse the inside of the pre-filter
housing and the leaf trap O-ring with
a garden hose.
7. Reinstall the leaf trap O-ring, basket and leaf
trap cover to the pre-filter housing.
8. Close the sediment release valve (19) back.
FLOW SENSOR CLEANING
1. In a counter-clockwise motion unscrew the collar of the flow sensor (21)
and remove it from the electrolytic cell conduit (22). See “Part Reference”.
2. If deposits and debris are seen on the surface of the flow sensor, then use
a garden hose to wash it off.
3. If flushing with water does not remove the deposits, use a plastic brush to
clean the surface and the hinge if necessary. Do not use a metal brush.
4. After the flow sensor has been inspected and cleaned, align the locator
notchontheflowsensortotheconnectionridgeintheconduit.Nowturn
the collar in a clockwise motion, tightening the sensor back into its position.
Do not overtighten.
Connection Ridge
LocatorNotch
Hinge
35
14
16
15
1
2
34
19
41
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 29
English
MAINTENANCE
ELECTROLYTIC CELL CLEANING
COPPER ELECTRODE CLEANING
If the pool water is hard (high mineral content) the cell may require periodic manual
cleaning. To maintain maximum performance, we recommend that you open and
visually inspect the electrolytic cell (22) once every month.
The following steps are some instructions on how to clean your cell.
1. Switch off the unit, unplug the power cord from the electrical socket.
2. Disconnect the hose (12) from the electrolytic cell (22) outlet and cover the
outlet with the drain outlet cover (3) from the 6-way valve (see drawings 36
and 37).
3. Remove the electrolytic cell from the 6-way valve outlet by unscrewing the
electrolytic cell (22) collar (see drawing 38).
4. Pour kitchen grade vinegar into the cell to immerse the titanium plates (see
drawing 39). Soak for about 1 hour and then flush with a high-pressure
garden hose.
5. Reverse steps 2 to 4 to reconnect the electrolytic cell.
1. Switch off the unit, unplug the power cord from the electrical socket.
2. In a counter-clockwise motion, unscrew the electrical plug collar from the
copper electrode cell, and remove the electrical plug from electrode cell (see
drawings 40 and 41).
3. Unscrew the copper electrode cell collar, then remove the electrode cell and
place it on a bucket.
4. Pour kitchen grade vinegar into the bucket until the copper electrode cell is
immersed (see drawing 43). Soak for 1 hour and then flush with a
high-pressure garden hose.
5. Reverse steps 2 to 4 to reconnect the copper electrode cell.
37
36 39
3
22
38
22
41 42
40 43
24
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 30
English
POOL CARE & CHEMICALS
• Allpoolsrequirecaretokeepthewaterclearandhygienicallyclean.Withproper
chemical control, your filter will help attain this objective. Consult your pool supply dealer
for instructions regarding the proper use of chlorine, algaecide and other chemical
agents required for sparkling clear water.
• Keeppoolchemicalsawayfromchildren.
• Donotreplenishchemicalsinpoolwhilepoolisoccupied.Skinoreyeirritationscould
occur.
• DailypHcheckingandchemicaltreatmentofthewaterisveryimportantandcannotbe
overemphasized.MaintenanceofproperpHlevelsarerequiredwhenfillingthepoolas
well as during the season. Consult your local swimming pool supply store for
instructions.
• Theseason'sfirstfillingofthepoolmayhavebrackishwaterrequiringextrawater
additivesandextrafilteringtime.DonotallowswimminginpooluntilthepHlevelis
balanced. Consult your local swimming pool supply store for instructions.
• Chlorinatedwatermaydamagelawns,gardensorshrubberyaschildrenplayinthepool
and splash water outside the pool. Lawn areas underneath the pool liner will be
destroyed.Notethatsometypesofgrassmaygrowthroughtheliner.
• Filterruntimedependsonpoolsize,weatherandusagelevel.Experimentwithvarious
run times so as to produce clean clear water.
MAINTENANCE
MAINTENANCE (continued)
The3-WayTestStripscantestthe“FreeChlorine”,“pH”,and“TotalAlkalinity”levelsatthe
same time. We recommend that you test the water chemistry weekly, and maintain the
chlorine concentration at 0.5-3 ppm.
Directions and Use
1. Dip the entire strip into the water and remove immediately.
2. Holdthestriplevelfor15seconds.Donotshakeexcesswaterfromthestrip.
3. Nowcomparethestrippadtothecolorchartonthepackaginglabel.Ifnecessary,
adjust the chemical level in the pool water. It is very important, to use the proper
techniquewhentestingthewater'schemicallevel.Readandfollowthewrittenstrip
instructions carefully.
INTEX
®
3-WAY TEST STRIPS (PACKED WITH THE PRODUCT)
The Copper Ion Test Strips can be used to test the copper ion concentration in the water.
Directions and Use
1. Dip the entire strip into the water for 3 seconds, then remove it.
2. Holdthestriplevelfor15seconds.Donotshakeexcesswaterfromthestrip.
3. Nowcomparethecopperionstrippadtothecolorchartonthepackaginglabel.
INTEX
®
COPPER ION TEST STRIPS (PACKED WITH THE PRODUCT)
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 31
English
POOL MAINTENANCE & CHEMICAL DEFINITIONS
MAINTENANCE
Free Chlorine - Is the chlorine residual present in pool water.
Combined Chlorine - Is formed by the reaction of free chlorine with ammonia
wastes.
Result if too high - Sharp chlorinous odor, eye irritation.
pH
- A value that indicates how acidic or basic a solution is.
Result if too low - Corroded metals, eye & skin irritation,
destruction of total alkalinity.
Result if too high - Scale formation, cloudy water, shorter
filter runs, eye & skin irritation, poor
chlorine efficiency.
Total Alkalinity - Indicatesthedegreeofthewater'sresistancetochange
inpH.ItdeterminesthespeedandeaseofpHchange,
soalwaysadjusttotalalkalinitybeforeadjustingthepH
level.
Result if too low - Corroded metals, eye & skin irritation.
LowalkalinitywillcausethepHtobe
unstable. Any chemical added to the
waterwillhaveanaffectonpH.
Result if too high - Scale formation, cloudy water,
eye & skin irritation, poor chlorine
efficiency.
Calcium Hardness - Refers to the amount of calcium and magnesium
dissolved in the water.
Result if too high - Scale will form and will cause the
water to become cloudy.
Stabilizer - Stabilizers extend the life of chlorine in swimming pools.
(Cyanuric Acid)
Consult with local swimming pool dealer for water treatment.
• Donotaddpoolchemicalsdirectlytotheskimmer.Thismaydamagethecell.
•Maintainingasaltandsanitizerlevelabovetherecommendedrangecan
contribute to the corrosion of the pool equipment.
• Checktheexpirydateofthetestkitasthetestresultsmaybeinaccurateifthe
kit is used after that date.
• If,duetoheavypoolusage,itisrequiredtoincreasethesanitizerlevel,thenuse
a chemical based on trichlor, TCCA or dichloro.
Preferred Water Chemistry Reading
Minimum Ideal Maximum
Copper Ions 0 0.1 - 0.2 ppm 0.2 ppm
Free Chlorine 0 0.5 - 3.0 ppm 5.0 ppm
Combined Chlorine 0 0 ppm 0.2 ppm
pH 7.2 7.4 - 7.6 7.8
Total Alkalinity 100 ppm 100 - 140 ppm 140 ppm
Calcium Hardness 150 ppm 200 - 400 ppm 500 - 1000 ppm
Stabilizer (Cyanuric Acid) 10 ppm 20 - 40 ppm 50 ppm
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 32
English
MAINTENANCE
1. Beforeemptyingyourpoolforlongtermstorage,orrelocation,besurethe
water is directed towards an acceptable drain water receptacle away from the
house. Check local regulations for specific directions regarding disposal of
swimming pool water.
2. Switch off the unit, and disconnect power cord from electrical outlet.
3. When the pool is empty, disconnect all hoses from pump and plunger valves
and remove the strainers/plunger valves from the pool wall.
4. In a counter clockwise motion unscrew the drain valve cap (9) from the drain
valve to thoroughly drain the tank. The drain valve is located at the bottom of
the filter tank.
5. Disassemble the pump motor from the tank base.
6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.
7. Coat the following o-rings and washers with petroleum jelly for long term
storage:
• L-shapeo-ring(27).
• o-ringA(18).
• PumphoseO-rings(29).
• Strainervalveassemblystepwashers(30).
• Flatstrainerrubberwashers(32).
8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve
top“N”position.Thisallowsthewatertodrainfromthevalve.Leavethe6-way
valve in this inactive position.
9.
It is best to place all dry pieces and pump motor in the original packaging for
storage. To avoid condensation or corrosion problem, do not cover or wrap pump
motor with plastic bags.
10. Storethepumpmotorandaccessoriesinadryplace.Thestorage's
temperature should be controlled, between 0 degrees Celsius (32 degrees
Fahrenheit)and40degreesCelsius(104degreesFahrenheit).
LONG TERM STORAGE & WINTERIZATION
CAUTION
Allowing the water to freeze will damage the sand filter and void the warranty.
If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is
non-toxic and will not damage plastic system components; other anti-freezes
are highly toxic and may damage plastic components in the system.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 33
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
English
• Linecordmustbepluggedintoa3wire
outletthatisprotectedbyaClassAGround
FaultCircuitInterrupter,orRCD.
• Resetcircuitbreaker.Ifcircuitbreakertrips
repeatedly, your electrical system may have
a defect. Turn off circuit breaker and call an
electrician to correct the problem.
• Letthemotorcooldownandrestartagain.
• See“Saltwatersystemoperation”.
• See“Cyanuricacidtable”.
• AdjustthechlorineandpHlevel.Consultyour
local swimming pool supply stores.
• Loadwithfiltersand,see“sandloading
instructions”.
• Setvalveto“FILTER”position.
• Operatethefilterforlongerperiods.
• UseIntexpoolvacuumtocleanbottomofpool.
• Cleanthebasket.
• Clearanyobstructionsintheintakehosebydischargingit
inside pool wall.
• Tightenhosenuts,checkhosesfordamage,checkpoolwater
level.
• Cleanthepre-filteringbasketmoreoften.
• Backwashfilter.
• Installthenozzleattheupperpositionofthepoolinlet,and
the strainer at the lower position of the pool outlet.
• Removeabout1”ofsandifnecessary.
• Removeanypoolvacuumingdeviceattachedtothesystem
line.
• Turnoffpump,clearanydebrisorobstructionintheoutlet,
remove all air from the filter pump and turn pump on again.
• Turnoffpump,ifwaterleakingfromthevacuumrelease
valve, then release valve needs to be replaced. Contact
Intex Service Center immediately to order replacement.
Youmaycoverreleasevalvewiththecaptemporarilyifyou
ensure that the strainer cover / strainer grid is installed and
you Do Not run the pump while pool is occupied.
• Fillpooltocorrectwaterlevel.
• Cleanstrainerscreensatpoolinlet.
• Tightenhosenuts,checkhosefor
damage.
• ContactIntexservicecenter.
•
Remove 6-way valve cover and ensure the
o-ring is in place.
Clean sand tank o-ring with garden hose water.
Tighten the clamp with wrench supplied.
Contact Intex service center.
• Tighten/reinstallhosenut.
• Ensureo-ring/L-shapeo-ringisinplace
and not damaged.
• Clearanyobstructionsintheintakeby
unscrewing it from the 6-way valve.
• ContactIntexservicecenter.
• UseonlyNo.20silicasandwithparticlesize
range 0.45 to 0.85 mm (0.018 to 0.033 inches)
and a Uniformity Coefficient less than 1.75.
• Changesand.
FILTERMOTOR
FAILSTOSTART
FILTERDOESN’T
CLEANPOOL
FILTERDOESN’T
PUMP WATER OR
FLOWISVERY
SLOW
PUMPDOESN’T
WORK
6-WAYVALVE/
COVERLEAKING
HOSELEAKING
PRESSUREGAUGE
DOESN’TWORK
SANDISFLOWING
BACKINTOTHE
POOL
• Thepowercordisloose.
• TheGFCI/RCDcircuitbreaker
is tripped.
• Motortoohotandoverload
protection is shut off.
• Stand-by/powersavingmode.
• Withoutcyanuricacid.
• ImproperchlorineorpHlevels.
• Nofilteringmediaintank.
• Wrong6-wayvalvesetting
position.
• Excessivelydirtypool.
• Dirtorsandon poolfloor.
• Thebasketisrestrictingthewater
flow.
• Cloggedinletordischarge.
• Anairleakontheintakeline.
• Excessivelydirtypool.
• Sandmediacloggedwithdirt.
• Nozzleandstrainer
connections are reversed.
• Crustingorcakingonthe
filtering sand surface.
• Poolvacuumingdevice
attached to the system.
• Thevacuumreleasevalveonthe
plunger valve is activated.
• Thevacuumreleasevalveonthe
plunger valve is leaking.
• Lowwaterlevel.
• Strainerscreencloggedup.
• Anairleakontheintakehose.
• Faultymotorortheimpeller
is jammed.
• Sandtanko-ringmissing.
• Sandtanko-ringdirty.
• Flangeclampnottight.
• 6-wayvalvedamage.
• Hosenutnotsecurelytight.
• Hoseconnectionfitting
o-ring/L-shape o-ring missing.
• Cloggedinletofthepressure
gauge.
• Pressuregaugedamage.
• Sandistoosmall.
• Sandbediscalcified.
TROUBLE CAUSE SOLUTION
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 34
English
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE (continued)
INSUFFICIENT
CHLORINE
INSUFFICIENT
COPPERION
LEVEL
POOLISSTAINED
WHITEFLAKESIN
THEWATER
NOLEDDISPLAY
GREENHAIR
Without cyanuric acid.
• Insufficient operating hours of
the Saltwater System.
• The salt level in the pool water
is less than 2000ppm. This is
insufficient.
• Chlorine loss due to intense
sunlight exposure.
• The bather load has increased.
• Clogged or dirty electrolytic cell.
• HighUVlevelexposure.
• Insufficient operating hours.
• The PHistoohigh.
• The bather load has increased.
• Clogged or dirty electrolytic cell.
• Copper electrode defective.
• Highcopperionconcentration.
• Excessive calcium hardness is
present in pool water.
Nopowersupply.
• RCD/GFCIhasnotreseted.
• A power fuse has blown.
• LED failure.
• Highcopperionconcentration.
• See “Cyanuric acid table”.
•
Increase the daily Saltwater System
operating time. See “Operating Instructions”.
CheckthesaltlevelwiththeTestKit.Adjust
asneeded.See“Salt&PoolWaterVolumes”.
Use a pool cover when the pool is not in use
and/or when the unit is operating.
Increase the daily Saltwater System operating
time. See “Operating Instructions”.
Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
• Coverthepoolwithapoolcoverfor2dayswith
the device running and then test the water
using the test strips.
• Ifthepooliscleanandclear,addstabilizerto
the water and then test the water.
Increase operating time per day. See
“Operating Instructions”.
UsePHdecreasechemicaltoadjust,
contact your local pool chemical store.
Increase the operating time per day.
See “Operating Instructions”.
Remove the cell for inspection, clean it
if necessary. See “Maintenance”.
Contact Intex Service Center.
•
Drainabout20%ofthepoolwaterandadd
fresh water to decrease the copper ion
concentration below 0.2ppm.
Add aluminum sulfate: 1000 liters water need
around 2g (1000 gals need 0.27 ounce) or
aluminum potassium sulfate: 1000 liters water
need around 3g (1000 gals need 0.4 ounce)
to pool.
Use a lemon based cleaning product
(preferably containing citric acid). Don’t scrub
with aggressive cleaning products because
this might etch the underlying surface.
Drainabout20to25%ofthepool
water and add fresh water to decrease
the calcium hardness. Inspect the
electrolytic cell for scale buildup. Clean
the electrolytic cell if necessary.
Plug the cell cord firmly into the cell
housing receptacle.
ResettheRCD/GFCI.
Contact Intex Service Center.
Contact Intex Service Center.
• Drainabout20%ofthepoolwaterand
add fresh water to decrease the copper
ion concentration below 0.2ppm.
• Add aluminum sulfate: 1000 liters
water need around 2g (1000 gals need
0.27 ounce) or aluminum potassium
sulfate: 1000 liters water need around
3g (1000 gals need 0.4 ounce) to pool.
Use ‘Ultra-Swim’ shampoo, or shampoo
containing chelating agents.
PROBLEM CAUSE SOLUTION
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 35
English
TROUBLESHOOTING GUIDE (continued)
1. Circulation line is blocked.
2. Incorrect inlet and outlet hose
direction.
3. Scale on the flow sensor.
4.Flowsensorcordisloose.
5. Device is set and operating in
backwash, rinse or waste mode.
6.Flowsensorfailure.
1. Dirt or scale on titanium plates.
2.Lowsaltlevel/Nosalt.
3. Electrolytic cell cord is loose.
4. Possible electrolytic cell failure.
1.Highsaltlevel.
2. Possible electrolytic cell failure.
1. Display and all lights are off - the
system does not power up.
• If your unit has plunger valves, ensure
that they are open.
• Clear your basket and cell from
debris and dirt. See “Maintenance”.
• Depress the 6-way valve, release all
trapped air in the circulation line.
• Check the direction of the inlet and the
outlet hose. Reverse the hoses if
necessary. See “Set Up Instructions”.
• Clean the flow sensor, paying special
attention to the hinge. See
“Maintenance”.
Plug the flow sensor firmly into the flow
sensor receptacle.
• Ignorethealarm,finishthebackwash,rinse
or waste operation then turn the power
switchOFFandONagaintoresetthealarm.
Contact Intex Service Center.
Remove the electrolytic cell for
inspection. Clean it if necessary.
See “Maintenance”.
Add salt. See “Salt & Pool Water
Volumes”.
Ensure that the cell cord is plugged
firmly into the cell housing receptacle.
Contact Intex Service Center. Replace
the cell if needed.
Partially drain the pool and refill it with
fresh water. See “Salt & Pool Water
Volumes”.
Contact Intex Service Center. Replace
the cell if needed.
Householdvoltageistoohighortoolow
(+20%).Checkthevoltageiswithinthe
range stated on the device housing.
Contact Intex Service Center.
LED PANEL
CODE PROBLEM SOLUTION
LEDPanelCodeFlash&AlarmOn(NOTE: Always turn off the power before cleaning and servicing).
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 36
COMMON POOL PROBLEMS
COMMON PROBLEMS
English
PROBLEM DESCRIPTION CAUSE SOLUTION
ALGAE
COLORED
WATER
FLOATING
MATTERIN
WATER
CHRONIC
LOW WATER
LEVEL
SEDIMENT
ONPOOL
BOTTOM
SURFACE
DEBRIS
•ChlorineandpHlevels
need adjustment.
•Copper,ironor
maganese in water
being oxidized by the
added chlorine.
This is Common.
•"Hardwater"caused
byatoohighpHlevel.
•Chlorinecontentislow.
•Foreignmatterin
water.
•Riporholeinpool
liner or hoses.
•Thedrainvalvesare
loose.
•Heavyuse,gettingin
and out of pool.
•Pooltoocloseto
trees.
• Superchlorinatewithshock
treatment.CorrectpHtoyour
poolstore'srecommended
level.
• Vacuumpoolbottom.
• Maintainproperchlorine
level.
• AdjustpHleveltothe
recommended level.
• Runfilteruntilwaterisclear.
• CorrectthepHlevel.Check
with your pool dealer for
advice.
• Adjustthechlorinelevel.
• Repairwithapatchkit.
• Fingertightenallcaps.
• UseIntexpoolvacuumto
clean bottom of pool.
• UseIntexpoolskimmer.
•Greenishwater.
•Greenorblack
spots on pool liner.
•Poollineris
slippery and/or has
a bad odor.
•Waterturnsblue,
brown, or black
when first treated
with chlorine.
•Wateriscloudyor
milky.
•Levelislowerthan
on previous day.
•Dirtorsandon
pool floor.
•Leaves,insects
etc.
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 37
SAFETY GUIDELINES
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demandconstantsupervision.Acompetentadultshouldbeappointedas
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learntoswim.
• TakethetimetolearnCPRandfirstaid.
• Instructanyonewhoissupervisingpoolusersaboutpotentialpool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instructallpoolusers,includingchildrenwhattodoincaseofan
emergency.
• Alwaysusecommonsenseandgoodjudgementwhenenjoyingany
water activity.
• Supervise,supervise,supervise.
For additional information on safety, please visit
•TheAssociationofPoolandSpaProfessionals:TheSensibleWay
to Enjoy Your Aboveground/Onground Swimming Pool
www.nspi.org
• AmericanAcademyofPediatrics:PoolSafetyforChildren
www.aap.org
• RedCrosswww.redcross.org
• SafeKidswww.safekids.org
• HomeSafetyCouncil:SafetyGuidewww.homesafetycouncil.org
• ToyIndustryAssociation:ToySafetywww.toy-tia.org
English
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 38
English
LIMITED WARRANTY
YourSandFilterPump&Saltwatersystemhasbeenmanufacturedusingthehighestquality
materials and workmanship. All Intex products have been inspected and found free of defects
priortoleavingthefactory.ThisLimitedWarrantyappliesonlytotheSandFilterPump&
Saltwater system and accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initialretailpurchase.Keepyouroriginalsalesreceiptwiththismanual,asproofofpurchase
will be required and must accompany warranty claims or the Limited Warranty is invalid.
SandFilterPump&SaltwatersystemWarranty2Years
TitaniumElectrodeWarranty–1Year
Hoses,PlungerValves&FittingsWarranty–180days 
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in the separate “Authorized Service Centers” sheet.
The Service Center will determine the validity of the claim. If the Service Center directs you
to return the product, please carefully package the product and send with shipping and
insurance prepaid to the Service Center. Upon receipt of the returned product, the Intex
Service Center will inspect the item and determine the validity of the claim. If the provisions
of this warranty cover the item, the item will be repaired or replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought before
an informal dispute settlement board and unless and until the provisions of these paragraphs
are carried forth, no civil action may be instituted. The methods and procedures of this
settlementboardshallbesubjecttotherulesandregulationssetforthbytheFederalTrade
Commission(F.T.C.).IMPLIEDWARRANTIESARELIMITEDTOTHETERMSOFTHIS
WARRANTYANDINNOEVENTSHALLINTEX,THEIRAUTHORIZEDAGENTSOR
EMPLOYEESBELIABLETOTHEBUYERORANYOTHERPARTYFORDIRECTOR
CONSEQUENTIALDAMAGESORLIABILITIES.Somestates,orjurisdictionsdonotallow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This Limited Warranty does not apply if products are subject to negligence, abnormal use
or operation, accident, improper operation, improper voltage or current contrary to operating
instructions, or to damage by circumstances beyond Intex’s control, including but not limited
to, ordinary wear and tear and damage caused by exposure to fire, flood, freezing, rain, or
other external environmental forces. This Limited Warranty applies only to those parts and
components sold by Intex. The Limited Warranty does not cover unauthorized alterations,
repairs or disassembly by anyone other than Intex Service Center personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN
OR REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex CS20110 Krystal Clear bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex CS20110 Krystal Clear in de taal/talen: Engels als bijlage per email.

De handleiding is 12,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info