12124
46
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
i400PRO
UHF TRANSCEIVER
INSTRUCTION MANUAL
IC-400PRO.qxd 03.6.19 6:13 PM Page a (1,1)
i
RWARNING! NEVER connect the transceiver to an
AC outlet. This may pose a fire hazard or result in an electric
shock.
RWARNING! NEVER operate the transceiver while
driving a vehicle. Safe driving requires your full attention—
anything less may result in an accident.
NEVER connect the transceiver to a power source of more
than 16 V DC. This will damage the transceiver.
NEVER cut the DC power cable between the DC plug and
fuse holder. If an incorrect connection is made after cutting,
the transceiver might be damaged.
NEVER place the transceiver where normal operation of
the vehicle may be hindered or where it could cause bodily
injury.
NEVER allow children to play with any radio equipment
containing a transmitter.
NEVER expose the transceiver to rain, snow or any liquids.
The transceiver may be damaged.
NEVER operate or touch the transceiver with wet hands.
This may result in an electric shock or damage the transceiv-
er.
PRECAUTION
Icom, Icom Inc. and the logo are registered trademarks of Icom
Incorporated (Japan) in the United states, the United Kingdom, Germany,
France, Spain, Russia and/or other countries.
SmarTrunk II™ is a trademark of the SmarTrunk Systems, Inc.
IMPORTANT
EXPLICIT DEFINITIONS
WORD DEFINITION
RWARNING
Personal injury, fire hazard or electric shock
may occur.
CAUTION
Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL This
instruction manual contains important operating instructions
for the IC-400PRO UHF TRANSCEIVER.
IC-400PRO.qxd 03.6.19 6:13 PM Page i (1,1)
ii
DO NOT push the PTT when not actually desiring to trans-
mit.
DO NOT use or place the transceiver in areas with tem-
peratures below –10°C or above +60°C, or in areas subject to
direct sunlight, such as the dashboard.
AVOID operating the transceiver without running the vehi-
cle’s engine. When the transceiver’s power is ON and your
vehicle’s engine is OFF, the vehicle’s battery will soon
become exhausted.
AVOID placing the transceiver in excessively dusty envi-
ronments.
AVOID placing the transceiver against walls. This will
obstruct heat dissipation.
AVOID setting the transceiver in a place without adequate
ventilation. Heat dissipation may be affected, and the trans-
ceiver may be damaged.
AVOID the use of chemical agents such as benzine or
alcohol when cleaning, as they damage the transceiver sur-
faces.
USE the specified microphone only (supplied or optional).
Other microphones have different pin assignments and may
damage the transceiver.
BE CAREFUL! The transceiver will become hot when
operating continuously for long periods.
This device complies with Standard
Australia Specification No. AS/NZS4365-
1996 and AS4295-1995.
IC-400PRO.qxd 03.6.19 6:13 PM Page ii (1,1)
iii
TABLE OF CONTENTS
IMPORTANT ........................................................................ i
EXPLICIT DEFINITIONS ..................................................... i
PRECAUTION ..................................................................... i
TABLE OF CONTENTS ...................................................... iii
SUPPLIED ACCESSORIES ............................................... iv
1 PANEL DESCRIPTION ............................................... 1–4
Front panel ................................................................... 1
Function display ........................................................... 4
2 BASIC OPERATION .................................................... 5–6
Turning power ON ........................................................ 5
Channel selection ......................................................... 5
Receiving and transmitting ........................................... 6
3 REPEATER OPERATION ............................................... 7
Repeater operation.........................................................7
Accessing a repeater......................................................7
4 SCAN OPERATION ................................................... 8–14
Scan types......................................................................8
Scanning preparation .....................................................9
Open scan ....................................................................11
Group and priority scans ..............................................12
Repeater search scan ..................................................13
5 GROUP MODE OPERATION .................................. 15–16
Group mode (CTCSS)..................................................15
6 SELCALL OPERATION .......................................... 17–21
General.........................................................................17
Calling operation ..........................................................17
When receiving a call ...................................................20
Setting the silent stand-by condition.............................21
7 OTHER FUNCTIONS .............................................. 22–33
Smart-Ring and ATS
(Automatic Transponder System) .....22
Voice scrambler function ..............................................23
DTMF transmission ......................................................24
Channel lock function ...................................................24
RX frequency setting ....................................................25
Wide/Narrow function ...................................................26
Set mode ......................................................................27
8 PROGRAMMABLE FUNCTION KEYS ................... 34–36
9 CONNECTION AND MAINTENANCE .................... 37–40
Rear panel and connection ........................................ 37
Mounting the transceiver ............................................. 38
Optional UT-108 installation ....................................... 39
Optional UT-109 or UT-110 installation ...................... 39
Optional OPC-617 installation ..................................... 40
Antenna ....................................................................... 40
Fuse replacement ....................................................... 40
Cleaning ..................................................................... 40
10 SPECIFICATIONS ....................................................... 41
11 OPTIONS ..................................................................... 42
IC-400PRO.qxd 03.6.19 6:13 PM Page iii (1,1)
iv
q Microphone .................................................................. 1
w Microphone hanger and screw set .......................... 1 set
e Microphone hanger cable .............................................. 1
r DC power cable (OPC-1194) ..........................................1
t Function name stickers* (KEY STICKER) ......................1
y Mounting bracket ........................................................... 1
u Bracket bolts ................................................................. 4
i Mounting screws (M5×12) ............................................. 4
o Self-tapping screws (M5×20) ......................................... 4
!0 Flat washers .................................................................. 4
!1 Spring washers ............................................................. 4
!2 Nuts ............................................................................... 4
*Function name stickers
Function of keys can be changed. Stickers are supplied for
easy identification.
qw
e
ry
u
i
o
!0
!1
!2
t
KEY-STICKER
ICOM
SUPPLIED ACCESSORIES
IC-400PRO.qxd 03.6.19 6:13 PM Page iv (1,1)
1
1
PANEL DESCRIPTION
ie
q
Function Display (p. 4)
w
u y t r
Speaker
Front panel
q AF VOLUME CONTROL KNOB
Rotate the knob to adjust the audio output level.
Minimum audio level is pre-programmed.
w []/[ ] KEYS*
Push to select an operating channel.
After pushing [
O
], push to toggle between CB bank and
Private bank (user programmable channels).
e POWER SWITCH [ ]
Push to turn the power ON and OFF.
The Automatic scan start function and the password prompt are
available at power ON as optional settings. (The optional CS-
400PRO
CLONING SOFTWARE
is required.)
r [O] KEY*
Push to enter channel bank selection mode.
In channel bank selection mode, push []/[]to select the
desired channel bank.
Push for 1 sec. to toggle Function mode, Set mode or
Normal mode.
Returns to the Normal mode automatically after 30 sec. when
no key operations are performed in Function or Set mode.
Normal mode
Set mode Function mode
Push [
O
]
for 1 sec.
IC-400PRO.qxd 03.6.19 6:13 PM Page 1 (1,1)
2
1
PANEL DESCRIPTION
1
t [DUP] KEY*
NN
NN
Push to toggle the transmit frequency mode between
duplex and simplex. (CB channel 1 to 8 only)
Duplex: The set TX frequency is used for the transmission.
Simplex: The set RX frequency is used for the transmis-
sion.
NN
NN
Push and hold to set the selected channel to priority
or normal.
Priority channel is used for both group and priority scans.
FF
FF
Push to toggle the 5tone mute activity between CONT
(Continuous Tone) and SGL (Single Tone).
CONT: SelCall mute is released.
SGL: SelCall mute is activated. In this case, [PTT] switch
action is inhibited while SelCall mute is activated.
y [SCN] KEY*
NN
NN
Push to start or stop the scan.
NN
NN
Push and hold to enter the scan type selection mode.
Push []/[]to select the desired scan type.
Push [SCN] to set the channel as a tag channel.
-
S
appears for tag channels.
FF
FF
Push to recall the received ID code.
Push []/[]to select the record.
u [MONI] KEY*
NN
NN
Activates the following functions on each channel
independently:
Push and hold the key to release the mute to the channel
(audio is emitted; Audible condition).
- “” appears.
During “” appears, push the key to mute the channel
(sets to Inaudible).
NOTE: The unmute condition (Audiblecondition)
may automatically return to the mute condition
(Inaudiblecondition) after a specied time period
depending on the pre-setting.
FF
FF
Push to transmit the SelCall code on the selected
channel.
FF
FF
Push and hold to enter the SelCall code/code number
selection mode (p. 17).
Push []/[]to select the desired code/code number.
*Information
Up to two desired functions, one each for Normal and
Function mode, can be re-assigned to [], [], [
O
],
[DUP], [SCN] and [MONI] keys with the optional CS-
400PRO
CLONING SOFTWARE
. (p. 34)
The default setting is used in this instruction manual, for
description.
NN
NN
: Stands for Normal mode operation.
FF
FF
: Stands for Function mode operation.
IC-400PRO.qxd 03.6.19 6:13 PM Page 2 (1,1)
3
1
PANEL DESCRIPTION
Key flow chart for the default setting
i MICROPHONE CONNECTOR
Connect the supplied microphone or optional DTMF micro-
phone.
NEVER connect non-specified microphones. The pin
assignments may be different and the transceiver may
be damaged.
DD
MICROPHONE
The supplied microphone has a PTT switch and a hanger
hook.
The following functions are available when the microphone is on or
off hook:
(The optional CS-400PRO
CLONING SOFTWARE
is required.)
- Automatic scan start when on hook.
- Automatic priority channel selection when off hook.
- Sets to Inaudible condition (mute condition) when on hook.
- Sets to Audible condition (unmute condition) when off hook.
Normal mode
Function mode
Set mode
: Set the desired level/mode.
: Change the individual setting.
/
: Change the common setting.
: Push to enter channel bank selection mode.
Push for 1 sec. to enter Normal mode.
: Turn the function ON and OFF.
: [CH Up] : [ID-MR Select]
: [Bank/Func]
: [CONT/SGL]
: [Call]
: [CH Down]
: [CH Up] : [Scan Start/Stop]
: [Bank/Func]
: [Dup/Pri]
: [Moni(Audi)]
: [CH Down]
Push [
O
] for 1 sec.
Push [
O
] for 1 sec.
Push [ ] to turn power ON.
IC-400PRO.qxd 03.6.19 6:13 PM Page 3 (1,1)
4
1
PANEL DESCRIPTION
1
Function display
q TRANSMIT INDICATOR
Appears while transmitting.
w BUSY INDICATOR
Appears while receiving a signal or when the squelch is
open.
e SIGNAL STRENGTH METER
Indicates relative receive signal strength level.
r LOW POWER INDICATOR
Appears when low output power is selected.
[High/Low] must be assigned to the desired program-
mable key using the optional CS-400PRO
CLONING
SOFTWARE
when change the output power.
t SQUELCH INDICATOR
Appears when the channel is in Audible condition
(SelCall/CTCSS mute is released).
y DUPLEX INDICATOR
Appears when the duplex operation is selected.
u SCRAMBLER INDICATOR
Appears when the scrambler function is activated. (Optional
UT-109 (#02)/UT-110 (#02) SCRAMBLER UNIT is required.)
i SELCALL/5TONE INDICATOR
Appears when the specied Selcall/5-tone is received.
o SCAN CHANNEL INDICATOR
Appears when the selected memory channel is specied
as a scan channel.
!0 ALPHANUMERIC DISPLAY
Displays the operating channel number, channel names,
Set mode contents, DTMF numbers, etc.
!1 UNDER BAR INDICATOR
Shows the channel mute condition (Inaudiblecondi-
tion) as below.
The left under bar blinks in Function mode, and lights in
Set mode.
Appears in Set mode when the key under the indicator
can be activated.
During “” appears, the channel is
Audiblecondition
even if the channel is in mute condition.
The channel is in CTCSS mute condition.
The channel is in SelCall mute condition.
The channel is in both CTCSS/SelCall mute
condition.
t
q
w
e
r
u
i
!0
oy
!1
IC-400PRO.qxd 03.6.19 6:13 PM Page 4 (1,1)
5
2
BASIC OPERATION
Turning power ON
Push [ ] to turn the power ON.
Channel selection
Push []/[]to select the desired operating channel.
While pushing and holding []or [], the displayed channel
changes continuously until channel number 01 appears.
When displayed channel stops at channel number 01, beeps
are emitted.
D Private channel selection
q Push [
O
] (Bank/Func) to enter the channel bank selection
mode. Then select the desired bank with []/[]. Push
[
O
] (Bank/Func) again to set the bank.
w Push []/[]to select the desired operating channel in
sequence.
NOTE: The selected channel is retained even when the
transceiver is turned off.
Push [
O
]
Push [] or []
Push []
About the password prompt:
If the transceiver is programmed for a start up passcode,
enter the specied 4-digit code.
(The optional CS-400PRO
CLONING SOFTWARE
is required.)
The keys in the table below can be used for password input:
The transceiver detects numbers in the same block as identical.
Therefore 01234 and 56789 are the same.
When the PASSWORD indication does not clear after
entering 4 digit code, the enter code number is incorrect. In
this case, turn the power off and start over.
KEY
NUMBER
01234
56789
IC-400PRO.qxd 03.6.19 6:13 PM Page 5 (1,1)
41
10
SPECIFICATIONS
DD
GENERAL
Frequency coverage
CB : 476.425477.400 MHz
Private : 450.000500.000 MHz (RX only)
Mode
CB : 16K0F3E
Private : 16K0F3E (Wide)/8K50F3E (Narrow)
Number of channels
CB : 40 channels/1 bank
Private : 88 channels/7 banks
Channel spacing
CB : ±25 kHz
Private : ±25 kHz (Wide)/±12.5 kHz (Narrow)
Current drain (approx.)
TX : (at 5W) 4 A
RX : Max. audio 1200 mA
Stand-by 300 mA
Power supply voltage : 13.8 V DC
Frequency stability : ±2.5 ppm
Antenna connector : SO-239 (50 )
Usable temperature range : 10°C to +60°C
Dimensions : 150 (W) × 40(H) × 117.5(D) mm
(Projections not included)
Weight (approx.) : 800 g
DD
TRANSMITTER
Output power (at 13.8 V DC) : 5 W
Modulation system :
Variable reactance frequency
modulation
Max. frequency deviation : ±5 kHz
Spurious emissions : 30 dBm
Adjacent channel power : 22 dBm
DD
RECEIVER
Sensitivity (12 dB SINAD) : 0.25 µV typ.
Squelch sensitivity : 0.25 µV typ. (Threshold)
Intermodulation rejection ratio:
70 dB
Spurious response rejection ratio
: 75 dB
Adjacent channel selectivity : 73 dB (Wide)/65 dB (Narrow)
Audio output power : 4.0 W typ. at 10% distortion with a 4
load
All stated specications are subject to change without notice or
obligation.
DD
Channel frequency list
CH
1
2
3
4
5
6
7
8
9
10
Freq.
476.425
476.450
476.475
476.500
476.525
476.550
476.575
476.600
476.625
476.650
CH
31
32
33
34
35
36
37
38
39
40
Freq.
477.175
477.200
477.225
477.250
477.275
477.300
477.325
477.350
477.375
477.400
CH
21
22
23
24
25
26
27
28
29
30
Freq.
476.925
476.950
476.975
477.000
477.025
477.050
477.075
477.100
477.125
477.150
CH
11
12
13
14
15
16
17
18
19
20
Freq.
476.675
476.700
476.725
476.750
476.775
476.800
476.825
476.850
476.875
476.900
IC-400PRO.qxd 03.6.19 6:13 PM Page 41 (1,1)
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Icom IC-400PRO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Icom IC-400PRO in de taal/talen: Engels als bijlage per email.

De handleiding is 1,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info