ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
1. Please read all instructions before using this fan.
2. Only use this fan as described in this manual. Other non-
recommended use may cause fire, electric shock, or injury.
3. Only connect the fan to a single-phase power socket with the
current as stated on its type plate.
4. Connect power after the fan has been fully assembled. Unplug
from outlet when moving fan from one location to another,
before putting on or taking off parts and before cleaning.
Disconnect the fan when not in use. Do not tug at the power cord
to disconnect the plug.
5. Supervision is needed when the fan is used anywhere near
children. This appliance is not intended for use by children or
other persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it safely.
6. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
7. Unwind the power cord completely. An incompletely unwound
power cord can lead to overheating and cause a fire. Do not touch
the power cord with wet hands. Position the power cord so that
nobody can trip over it and where the socket can be reached
easily.
8. Do not use an infinitely variable speed controller. This can lead
to overheating, fire, electric shock or faults in the appliance.
9. Do not operate the fan without the protective front and rear
grilles in position. Do not touch the rotating fan blades with any
part of the body. This can cause personal injury and damage.
10. Never insert fingers, pencils, or any other object through the
grille when fan is running.
11. Do not operate the fan if it is damaged or might be defective,
or if it is not working properly. Remove the power plug from the
socket.
12. Do not use the fan anywhere near easily inflammable gases or
substances such as solvents, lacquers, glues etc.
13. The fan is only designed for private use in indoor rooms and
is not intended for outdoor or for commercial use. Do not use the
fan anywhere near a bathtub, a shower or a swimming pool, or
anywhere else where water could splash.
14. Do not plunge the fan into water or any other liquids and do
not pour water or any other liquids over the fan.
15. Place the fan on a firm, even, dry surface. Be sure the fan is on
a stable surface when operating to avoid overturning. Make sure
the fan is standing securely so that it cannot tip over or fall down.
Maintain a safety distance of at least 50 cm from other objects.
16. Clean the fan regularly by following the cleaning instructions.
COMPONENTS
1. Front Grille
2. Spinner
3. Blades
4. Plastic Nut
5. Rear Grille
6. Motor Shaft
7. Speed Knob
8. Oscillating Clutch Knob
9. Motor Housing
10. Tilt Adjustment Knob
11. Power Supply Cord with Plug
12. Pedestal
13. Chassis
ASSEMBLY INSTRUCTIONS
Assembly of Fan Pedestal onto Chassis
1. Take the chassis and pedestal parts from the packing box
and unscrew the plastic nut on the pedestal (Fig. 1).
2. Insert the pedestal into the chassis by pushing
down until it locks into the chassis (Fig. 2).
3. Tighten the screw from the chassis to lock the
pedestal (Fig. 3).
Assembly of Blade and Grilles
1. Unscrew the spinner clockwise and the nut counter-clockwise,
then remove both of them (Fig. 4).
2. Place the rear grille on the motor shaft so that the handle is at
the top
3. Screw on plastic nut clockwise to attach rear grille tightly.
4. Remove and discard the small plastic sleeve on the motor shaft.
5. Install the blade onto the motor shaft until it reaches the
retaining pin (Fig. 5).
6. Make sure the fan blade slot fits into the retaining pin of the
motor shaft, then tighten the spinner counter-clockwise.
7. Secure both grilles firmly by tightening the screws. 1 Screw and
2 clips for HT-112E, 1 screw and 4 clips for HT-116E (Fig. 6).