568912
14
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
13
English
NOTE:
In intermittent operation, you cannot drive nails with
the trigger still held down, by again pressing the
push-lever up against the target spot. To continually
drive nails one after another, release your finger
from the trigger and switch to “continuous operation”.
If a nail driver placed on the floor (push-lever pressed
against the floor) is picked up while pulling the trigger,
the nail driver will shift to single shot and it may be
impossible to shoot nails even if the push-lever is
pressed against something. If that happens, release
your finger from the trigger and then try driving nails
again.
CAUTION
Exercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
NOTE:
Precautions on no-load operation.
Sometimes nailing will continue after driving in all
nails previously contained in the magazine.
This is termed “no-load operation”. Such operation
may deteriorate the bumper, magazine, and nail feeder.
To avoid no-load operation, occasionally confirm the
amount of remaining nails. On the other hand, all
nails should be removed after using this nailer.
After completing operation, put into the body about 2
cc oil through the hose joint to protect the tool from
rust.
Under low temperature conditions, the machine
sometimes does not operate correctly. Always operate
the machine at the appropriate ambient temperature.
3. Driving nails into steel plating
CAUTION
Use C-beam steel with a thickness of 3.2 mm or less.
Use hardened nails designed for use with steel plating.
Place the nailer vertically over the location into which
the nail is to be driven.
When galvanized steel or other metal plates are to be
attached directly onto C-beam steel, make sure they
are 0.7 mm or less in thickness.
Also, make sure that nails designed for use with steel
plating with a length of 32 mm are used.
Do not use the nailer on roofs or ceilings.
Make sure that the thickness of the hardened nails
designed for use with steel plating are of the correct
thickness for the C-beam steel.
NOTE:
Use the single shot setting to improve the finish after
the nails have been driven in.
Refer to the following table to select the correct nail shaft
diameter and length.
[Selecting Nail Shaft Diameter]
[Selecting Nail Length]
57 mm and 65 mm nails cannot be used on C-beams
with a thickness of 3.2 mm.
Make sure C-beam steel with a thickness of 2.3 mm or
less is used.
NOTE:
Holding power will be greatly decreased if nails are
driven too hard into steel plating. Rotate the adjuster
downwards to adjust the depth of the nails.
There are cases in which the nails will not be driven
in sufficiently depending on a combination of the
hardness and thickness of the C-beam or material.
4. Driving nails into concrete
CAUTION
Use hardened nails designed for use with concrete.
Place the nailer vertically over the location into which
the nail is to be driven.
Do not drive nails directly into concrete or attach
metal plates directly onto it.
Do not drive nails into the edge of concrete.
Do not use the nailer in locations from which other
items are suspended (suspended pipes, etc.).
NOTE:
Only use the nailer on concrete that has not yet set,
soon after it has been poured.
Using the nailer on hardened concrete may result in
bent nails and nails being insufficiently driven in.
Use the single shot setting to improve the finish after
the nails have been driven in.
[Selecting hardened nails for use with concrete]
Select nails with a concrete intrusion depth of between
10 to 15 mm.
C-Beam Steel Thickness Nail Shaft Diameter
2.3 mm or less 2.8 to 3.0 mm
3.2 mm or less 3.0 mm
Material Thickness Nail Length
Galvanized iron and other metal plates
0.7 or less (direct attachment) 32 mm
1.8 to 22 mm
14 to 35 mm 45 mm
15 to 45 mm 50 mm
22 to 47 mm 57 mm
30 to 55 mm 65 mm
The external material
and steel plating is not
deformed.
The external material
and steel plating is
deformed.
C-beam Steel
(Thickness: 1.6 mm to a
maximum of 3.2 mm)
Material Thickness
Approximately
10 to 35 mm
01Eng_NV75HMC_WE 3/13/12, 10:3913
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi NV75HMC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi NV75HMC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info