568912
13
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
12
English
does not exceed the specified limit. Note that
excessive pressure may affect overall performance,
service life, and safety.
2. Lock mechanism of the trigger
This device has a lock mechanism to prevent the
trigger from pulling.
Set the lock lever to “Lock” position to lock the trigger
in place.
To drive a nail, turn the lock lever to the “Free”
position. When not driving nails set the lever to the
“Lock” position (Fig. 2).
CAUTION
Keep the trigger locked at all times except when
driving nails.
3. Lubrication
(1) Be sure to lubricate this nailer at least twice a day. To
lubricate, pour 10 to 15 drops of oil into the air plug
before and after using this nailer. The oil applied
before use lubricates this nailer; the oil applied after
use prevents rust.
(2) It is recommended using the recommended oil (SHELL
TONNA). Other applicable oils are listed. Never mix
two or more types of different oils.
4. Nose Selection and Switching
This nailer allows you to switch the nail outlet between
two sizes to extend the range of usable types and
sizes of nails. Set the nose switch lever to select the
outlet size matching the head diameter of the nail to
be used as shown below (Fig. 3).
CAUTION
Be sure to disconnect the air hose before operating
the nose switch lever.
NOTE:
Be sure to switch to the appropriate nose for the nails
to be used. Selecting an inappropriate nose may
cause defective nailing or sparking. It may also cause
a nail jam, damage to this nailer or personal injury.
5. Load Nails
(1) Grip the nail guide and knob with finger.
Press the knob down and swing the nail guide open.
And open the magazine cover (Fig. 4).
(2) Adjust the position of the nail holder according to the
nail length (Fig. 5).
The nail will not feed smoothly if the nail holder is
not correctly adjusted (Fig. 6).
a. Turn the nail holder about 90 degrees
counterclockwise.
b. Slide in vertical direction possible.
Lift or lower the nail holder to accept different
length nails.
c. Adjust the plate to the nail length reference points
on the magazine cover and turn the nail holder 90
degrees clockwise until you hear “click”.
(3) Place the nail coil into the magazine.
Uncoil enough nails to reach the driving hole (Fig. 7).
When using wire collated nails
Insert the first nail into the driving hole and the
second nail between the two pawls of the feeder.
Fit the nail head in the guide slot (Fig. 8).
When using plastic sheet collated nails
Insert the first nail into the driving hole and the
second nail between the two pawls of the feeder.
Fit the nail head and upper side of the plastic sheet in
the guide slot.
Fit the lower side of the plastic sheet in the guide slot
for plastic sheets (Fig. 9).
(4) Close the magazine cover first and swing the nail
guide closed (Fig. 10).
(5) Lock the knob correctly.
NOTE:
Be careful not to deform the collated wires and not to
disengage the nails with the guide surface.
Otherwise, the nail guide will not close correctly.
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a
work bench or floor. Also, never face the nail outlet
toward any part of a person.
NOTE:
Before loading the nails in the magazine, position the
nail holder according to the length of the nail. If the
nail holder position is not adjusted properly, nail
feed may jam. If the cover is forcibly closed without
adjusting the position of the nail holder, the nail
holder may be damaged.
HOW TO USE THE NAILER
CAUTION
Never use the head or body of this device as a hammer.
Take precautions to ensure the safety of persons in
the vicinity during operation.
1. Set the lock lever to “Free” position
Turn the lock lever and align it with the “Free” position
(Fig. 11).
2. How to drive nails
This device is equipped with a mechanism allowing
“intermittent operation” or “continuous operation”
for most effective use according to the type material
the nails will be driven into.
(1) Intermittent operation
Intermittent operation nail driving is used when the
finished appearance is important and when driving a
nail in a particular spot.
Press the push-lever up
against the spot where you will drive the nail.
Drive the nails one at a time by pulling the trigger
(Fig. 12).
NOTE:
Use “intermittent operation” when you are aiming at
a particular spot to drive the nail.
(2) Continuous operation
To drive nails with contact drive:
First, pull the
trigger.
Then press the nail dispenser up against
the spots you want, to drive the nails one after another
at those spots (Fig. 13).
Head Diameter Outlet size
ø 5.6 mm – ø 7.5 mm
Small
(0.220" – 0.295")
ø 7.5 mm – ø 7.9 mm
Large
(0.295" – 0.311")
01Eng_NV75HMC_WE 3/13/12, 9:0812
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi NV75HMC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi NV75HMC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info