565926
16
Verklein
Vergroot
Pagina terug
1/232
Pagina verder
16
GB
1. Squeeze and release trigger to unlatch it and take control of the throttle.
2. Let engine warm to operating temperature before doing any cutting.
3. Take cutting stance on left side of cutter. Never get any part of your body
behind the cutter. Hold the cutter fi rmly with both hands. Throttle up to
cutting speed and make gentle wheel contact with the work.
Stopping Engine
Move ignition switch down to “STOP” position. Keep wheel in the clear until
all movement stops.
If engine does not stop, pull choke control knob out fully to stop engine. The
choked engine will slow to a stop. Be sure to keep the wheel in the clear until
all movement stops.
WARNING
With trigger latched, wheel will rotate as soon as engine starts. Keep
wheel in the clear.
Wheel will rotate for some time after the trigger is released. Keep
wheel in the clear until all movement stops.
Restarting Warm Engine
When engine is warm from previous running, move ignition switch to
“RUN” position. And push choke control knob all the way in. Try cranking
at idle throttle without latching it. If this does not work, try again with throttle
latched. Choking may be needed if the engine has cooled. But, to avoid
the possibility of over-choking and fl ooding, always fi rst try to start a warm
engine without choking it.
Sequence after Starting Engine
Cutting Asphalt, Tar and Reinforced Materials
Old, cold and hardened asphalt paving can be cut with a masonry wheel with
good results and little trouble with tarring of the wheel. Fresh asphalt and
tarred surfaces can gum up the wheel and slow its cutting action. Some tar
or resin-impregnated materials also may present problems of this sort.
Masonry containing metal reinforcement is best cut with a masonry wheel
which can cut through the reinforcing steel better than a wheel designed for
metal can cut the masonry. Expect faster than normal wheel wear.
DANGER
z Do not raise cutter above chest height, because the cutter is hard
to control when held up high, and dust or sparks will fall on you.
z Wear hearing protection. Without it you risk hearing loss,
especially where bounce-back of sound waves off nearby surfaces
increases the noise.
z Do not take awkward or risky operating positions. Find solid
footing for both feet, and always hold the cutter fi rmly with both
hands. Never make one-handed cuts.
z When the wheel engages the work, the thrust will exert a forward
pull which you must be ready to control. Keep bystanders out of
the way.
Wheel Thrust
CM14E_WE_all.indb 16CM14E_WE_all.indb 16 2008/02/05 21:09:322008/02/05 21:09:32
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CM14E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CM14E in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans als bijlage per email.

De handleiding is 9,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info